iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 573-3:2019+A2:2024

(Main)

Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products

Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products

This document specifies the chemical composition limits of wrought aluminium and wrought
aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely
identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington,
VA 22209, USA, for the corresponding alloys.

Aluminium und Aluminiumlegierungen - Chemische Zusammensetzung und Form von Halbzeug - Teil 3: Chemische Zusammensetzung und Erzeugnisformen

Aluminium et alliages d'aluminium - Composition chimique et forme des produits corroyés - Partie 3 : Composition chimique et forme des produits

Le présent document spécifie les limites de composition chimique des aluminiums et alliages d’aluminium corroyés et les formes de produits.
NOTE   Les limites de composition chimique de l’aluminium et des alliages d’aluminium spécifiées ici sont strictement identiques à celles enregistrées auprès de l’Aluminium Association, 1525 Wilson Boulevard, Suite 600, Arlington, VA 22209, États-Unis, pour les alliages correspondants.

Aluminij in aluminijeve zlitine - Kemična sestava in oblika gnetenih izdelkov - 3. del: Kemična sestava in oblika izdelkov (vključno z dopolnilom A2)

Ta dokument določa mejne vrednosti kemične sestave gnetenega aluminija in gnetenih
aluminijevih zlitin ter obliko izdelkov.
OPOMBA: Omejitve kemijske sestave aluminija in aluminijevih zlitin, navedene v tem dokumentu, so popolnoma enake omejitvam, ki so za ustrezne zlitine registrirane pri združenju Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, ZDA.

General Information

Status
Published
Publication Date
17-Mar-2024
ICS
77.040.30 - Chemical analysis of metals
77.120.10 - Aluminium and aluminium alloys
77.150.10 - Aluminium products
Technical Committee
INEK - Nonferrous metals
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
03-Jan-2024
Due Date
09-Mar-2024
Completion Date
18-Mar-2024
Ref Project
EN 573-3:2019+A2:2023 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products

Relations

Merged From
SIST EN 573-3:2019+A1:2022 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
Effective Date
25-Oct-2023
Merged From
SIST EN 573-3:2019+A1:2022/oprA2:2023 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
Effective Date
25-Oct-2023

Buy Standard

EN 573-3:2019+A2:2024EN 573-3:2019+A2:2024
PreviousNext
Standard
EN 573-3:2019+A2:2024
English language
57 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 573-3:2019+A2:2024
01-maj-2024
Aluminij in aluminijeve zlitine - Kemična sestava in oblika gnetenih izdelkov - 3.
del: Kemična sestava in oblika izdelkov (vključno z dopolnilom A2)
Aluminium and aluminium alloys - Chemical composition and form of wrought products -
Part 3: Chemical composition and form of products
Aluminium und Aluminiumlegierungen - Chemische Zusammensetzung und Form von
Halbzeug - Teil 3: Chemische Zusammensetzung und Erzeugnisformen
Aluminium et alliages d'aluminium - Composition chimique et forme des produits
corroyés - Partie 3 : Composition chimique et forme des produits
Ta slovenski standard je istoveten z: EN 573-3:2019+A2:2023
ICS:
77.040.30 Kemijska analiza kovin Chemical analysis of metals
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 573-3:2019+A2:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 573-3:2019+A2:2024

---------------------- Page: 2 ----------------------
SIST EN 573-3:2019+A2:2024


EN 573-3:2019+A2
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2023
EUROPÄISCHE NORM
ICS 77.120.10 Supersedes EN 573-3:2019+A1:2022
English Version

Aluminium and aluminium alloys - Chemical composition
and form of wrought products - Part 3: Chemical
composition and form of products
Aluminium et alliages d'aluminium - Composition Aluminium und Aluminiumlegierungen - Chemische
chimique et forme des produits corroyés - Partie 3 : Zusammensetzung und Form von Halbzeug - Teil 3:
Composition chimique et forme des produits Chemische Zusammensetzung und Erzeugnisformen
This European Standard was approved by CEN on 31 January 2022 and includes Amendment approved by CEN on 17 November
2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 573-3:2019+A2:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 573-3:2019+A2:2024
EN 573-3:2019+A2:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Chemical composition limits . 6
5 Writing rules . 6
6 Alloy designations . 7
7 Sequence of elements . 7
8 Rounding rules for determination of compliance . 7
Annex A (normative) Form of products . 32
A.1 General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 573-3:2019/oprA1:2021(Amendment)
Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
EN 573-3:2019/FprA1

This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 573-3:2019+A1:2022/oprA2:2023(Amendment)
Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
EN 573-3:2019+A1:2022/prA2

This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 573-3:2019/oprA1:2021(Amendment)
Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
EN 573-3:2019/FprA1

This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 573-3:2019+A1:2022/oprA2:2023(Amendment)
Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
EN 573-3:2019+A1:2022/prA2

This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 6185-3:2024(Main)
Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater (ISO 6185-3:2024)
EN ISO 6185-3:2024

This document specifies the minimum safety characteristics required for the design, materials, manufacture and testing of inflatable boats and rigid inflatable boats with a length of the hull LH in accordance with ISO 8666 less than 8 m with a motor power rating of 15 kW and greater.
This document is applicable to the following types of boats intended for use within the operating temperatures of –20 °C to +60 °C:
—     Type VII: Powered boats, fitted with a buoyancy tube on the port and starboard sides, suitable for navigation in conditions of design categories C and D.
—     Type VIII: Powered boats, fitted with a buoyancy tube on the port and starboard sides, suitable for navigation in conditions of design category B.
This document excludes single-chambered boats and boats with tubes made from unsupported materials, and does not apply to aquatic toys and inflatable liferafts.
Boats with tubes made from aluminium, roto-moulded polyethylene, fibre reinforced plastic or other rigid materials are excluded from this document.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28139:2021/A1:2024(Amendment)
Equipment for crop protection - Knapsack combustion engine-driven airblast sprayers - Safety and environmental requirements and test methods - Amendment 1 (ISO 28139:2019/Amd 1:2024)
EN ISO 28139:2021/A1:2024
  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17821:2023/AC:2024(Corrigendum)
Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification
EN 17821:2023/AC:2024

This document specifies:
- general construction, performance and material requirements for Frost Resistant Taps for outdoor use (FRT), PN 10.
- the application in the potable water installation with a static pressure of maximum 1,0 MPa (10 bar) and a distribution temperature of maximum 25 °C (PWC).
FRT valves shall consist of the 3 areas shown in Figure 1.
The conditions of use are according to the following Table 1.
The requirements with regard to the potable water quality are specified in national regulations.

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 21068-1:2024(Main)
Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 1: General information, terminology and sample preparation (ISO 21068-1:2024)
EN ISO 21068-1:2024

This part of ISO 21068 gives definitions and specifies techniques for the preparation of samples for the chemical analysis of silicon-carbide-containing raw materials and refractory products including:
a)   SiC raw materials;
b)   graphite brick containing silicon carbide;
c)   silicon carbide brick (includes the bricks containing silicon nitride, silicon oxynitride, sialon);
d)   refractories containing carbon and/or silicon carbide mixed with clay;
e)   refractories containing carbon and/or silicon carbide mixed with silica (and fused silica);
f)   refractories containing carbon and/or silicon carbide mixed with high alumina material;
g)   refractories containing carbon and/or silicon carbide mixed with magnesia (and dolomite);
h)   refractories containing carbon and/or silicon carbide mixed with chrome mineral or magnesia-chrome materials;
i)   refractories containing carbon and/or silicon carbide except those described in a) to g) above.
The items of chemical analysis described in ISO 21068, Parts 1 to 4 are as follows:
1)   loss on drying (LOD);
2)   loss on ignition (LOI);
3)   total carbon, Ctotal;
4)   free carbon, Cfree;
5)   silicon carbide, SiC;
6)   free silicon (Sifree);
7)   free aluminium (Alfree);
8)   free magnesium (Mgfree);
9)   free iron (Fefree);
10)   silicon(IV) dioxide (SiO2);
11)   aluminium oxide (Al2O3);
12)   iron(III) oxide (total iron oxide calculated as Fe2O3);
13)   titanium(IV) oxide (TiO2);
14)   calcium oxide (CaO);
15)   magnesium oxide (MgO);
16)   sodium oxide (Na2O);
17)   potassium oxide (K2O);
18)   chromium(III) oxide (Cr2O3);
19)   zirconium oxide (ZrO2);
20)   boron oxide (total boron calculated as B2O3);
21)   nitrogen;
22)   oxygen;
23)   nitrides (undifferentiated: Si3N4, AlN, BN, sialon, oxy-nitrides, etc.);
24)   XRD-methods.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1570-1:2024(Main)
Safety requirements for lifting tables - Part 1: Lifting tables serving up to two fixed landings
EN 1570-1:2024

1.1   This document specifies the safety requirements for lifting tables with the following properties:
-   serving no more than 2 fixed landings but are able to pass a fixed landing and,
-   having a vertical travel speed of no more than 0,15 m/s, unless safe by position and,
-   for raising or lowering goods (with or without operator(s) and/or authorised person(s)), or;
-   for raising or lowering operator(s) and/or authorised person(s) with or without goods, to positions where they can carry out work from a fixed or movable lifting table that is guided throughout its vertical travel only.
1.2   This document deals with all significant hazards pertinent, with the exception of noise, to lifting tables when used as intended and under the conditions foreseen by the manufacturer (see List of Hazards, Annex B). This document specifies the appropriate technical measures for eliminating and reducing the risks arising from the significant hazards.
1.3   This document does not apply to the following equipment:
-   lifting tables with a vertical travel speed exceeding 0,15 m/s, unless safe by position;
-   lifting tables, serving more than 2 fixed landings of a construction, for lifting goods, with a vertical travel speed not exceeding 0,15 m/s (EN 1570-2);
-   lifting tables, serving more than 2 fixed landings of a construction, for lifting operators, with a vertical travel speed not exceeding 0,15 m/s;
-   lifting tables carrying operators and installed in full enclosures with a vertical travel speed not exceeding 0,15 m/s;
-   lifting tables used on ships;
-   lifting tables designed for artists and stage set features during artistic performances;
-   power operated lifting platforms for persons with impaired mobility (EN 81-41);
-   mobile lifting tables for airport ground support equipment (EN 1915-2 and EN 12312-1);
-   lifting tables which are designed as part of a lift according to Directive (95/16/EC);
-   mobile elevating work platforms (EN 280);
-   static Group B elevating work platforms (EN 280);
-   vehicle servicing lifts (EN 1493);
-   mobile lifting tables used for firefighting (EN 1777);
-   mobile lifting tables with a horizontal travelling speed of more than 1,6 m/s;
-   rail dependent storage and retrieval equipment (EN 528);
-   scissor lift pallet trucks (EN ISO 3691-5);
-   lifting tables suspended from a ceiling.
1.4   This document does not consider the additional requirements for:
-   electromagnetic compatibility;
-   operation in severe conditions (e.g. extreme climates, freezer applications, strong magnetic fields);
-   operation subject to special rules (e.g. potentially explosive atmospheres, mines);
-   handling of loads, the nature of which could lead to dangerous situations (e.g. molten metal, acids, radiating materials, particularly brittle loads, loose loads (gravel, tubes));
-   hazards occurring during construction, transportation and disposal;
-   equipment installed on the load platform or the replacing or maintaining of it;
-   integration into broader systems or other machines, etc.;
-   cable-less controls;
-   lifting tables where the hydraulic pressure is derived directly from gas pressure;
-   lifting tables powered by internal combustion engines.

  • Standard
    85 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 12625-16:2024(Main)
Tissue paper and tissue products - Part 16: Determination of optical properties - Diffuse reflectance method for opacity (paper backing) (ISO 12625-16:2024)
EN ISO 12625-16:2024

ISO 12625-16:2015 specifies the testing procedures for the instrumental determination of the opacity of tissue paper or tissue products by diffuse reflectance using a paper backing.
ISO 12625-16:2015 contains specific instructions for the preparation of test pieces of single-ply and multi-ply products, where special preparation/procedures might be necessary.
It can be used to determine the opacity of tissue paper and tissue products containing fluorescent whitening agents, provided the UV content of the radiation incident on the test piece has been adjusted to conform to that in the CIE illuminant C using a fluorescent reference standard provided by an authorized laboratory as described in ISO 2470-1.
ISO 12625-16:2015 is not applicable to coloured tissue paper and tissue products which incorporate fluorescent dyes or pigments.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day