EN IEC 61010-2-010:2020

SLOVENSKI STANDARD
01-julij-2020
Nadomešča:
SIST EN 61010-2-010:2015
Varnostne zahteve za električno opremo za meritve, nadzor in laboratorijsko
uporabo - 2-010. del: Posebne zahteve za laboratorijsko opremo za gretje
materialov
Safety requirements for electrical equipment for measurement, control and laboratory
use - Part 2-010: Particular requirements for laboratory equipment for the heating of
materials
Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2
-010: Besondere Anforderungen an Laborgeräte für das Erhitzen von Stoffen
Règles de sécurité pour appareils électriques de mesurage, de régulation et de
laboratoire - Partie 2-010: Exigences particulières pour appareils de laboratoire utilisés
pour l’échauffement des matières
Ta slovenski standard je istoveten z: EN IEC 61010-2-010:2020
ICS:
19.080 Električno in elektronsko Electrical and electronic
preskušanje testing
71.040.10 Kemijski laboratoriji. Chemical laboratories.
Laboratorijska oprema Laboratory equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61010-2-010

NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2020
ICS 19.080; 71.040.20 Supersedes EN 61010-2-010:2014 and all of its
amendments and corrigenda (if any)
English Version
Safety requirements for electrical equipment for measurement,
control and laboratory use - Part 2-010: Particular requirements
for laboratory equipment for the heating of materials
(IEC 61010-2-010:2019)
Exigences de sécurité pour appareils électriques de Sicherheitsbestimmungen für elektrische Mess-, Steuer-,
mesurage, de régulation et de laboratoire - Partie 2-010: Regel- und Laborgeräte - Teil 2-010: Besondere
Exigences particulières pour appareils de laboratoire Anforderungen für Laborgeräte für das Erhitzen von Stoffen
utilisés pour l'échauffement des matières (IEC 61010-2-010:2019)
(IEC 61010-2-010:2019)
This European Standard was approved by CENELEC on 2019-03-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61010-2-010:2020 E

European foreword
This document (EN IEC 61010-2-010:2020) consists of the text of IEC 61010-2-010:2019 prepared by
IEC/TC 66 "Safety of measuring, control and laboratory equipment".
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-11-22
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-05-22
document have to be withdrawn
This document supersedes EN 61010-2-010:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
EN 61010-2-010:2014:
— adaptation of changes introduced by Amendment 1 of 61010-1;
— alignment with 61010-2-011 and 61010-2-012:
— New matching Introduction clarifying which standard(s) to use;
— new clause 5.4.102 instructions for flammable liquid heat transfer medium;
— clause 9.5 on flammable liquids replaced with text from 2-012;
— Equipment with high accessible current deleted;
— requirements in 10.101 b) and c) clarified;
— editorial corrections.
Endorsement notice
The text of the International Standard IEC 61010-2-010:2019 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60335-2-6:2014 NOTE Harmonized as EN 60335-2-6:2015
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Annex ZA of EN 61010-1:2010/A1:2019 is applicable with the following additions:
Publication Year Title EN/HD Year
ISO 7010 2011 Graphical symbols — Safety colours and safety EN ISO 7010 2012
signs — Registered safety signs
+Amd1
+Amd2
+Amd3
+Amd4
+Amd5
+Amd6
+Amd7
+Amd8
Annex ZZ
(informative)
Relationship between this European standard and the safety objectives of
Directive 2014/35/EU [2014 OJ L96] aimed to be covered
This European Standard has been prepared under a Commission’s standardization request relating to
harmonized standards in the field of the Low Voltage Directive, M/511, to provide one voluntary means
of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the
Council of 26 February 2014 on the harmonization of the laws of the Member States relating to the
making available on the market of electrical equipment designed for use within certain voltage limits
[2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding safety objectives of
that Directive, and associated EFTA regulations.
Table ZZ.1 – Correspondence between this European standard and Annex I of Directive
2014/35/EU [2014 OJ L96]
Clause(s) / sub-
Safety objectives of Directive
clause(s)
Remarks / Notes
2014/35/EU (Annex I)
of this EN
1. General conditions
5.1
1 (a) the essential characteristics, the
5.2
recognition and observance of which will
5.4
ensure that electrical equipment will be
used safely and in applications for which it
was made, shall be marked on the
electrical equipment, or, if this is not
possible, on an accompanying document
6.6
1 (b) the electrical equipment, together
6.10
with its component parts, shall be made in
6.11
such a way as to ensure that it can be
Annex F
safely and properly assembled and
connected
5.4
1 (c) the electrical equipment shall be so
17 (for
designed and manufactured as to ensure
hazards not
that protection against the hazards set out
covered by
in points 2 and 3 is assured, providing that
clauses 6-16)
the equipment is used in applications for
See also the
which it was made and is adequately
details in
maintained
points 2 and 3
Clause(s) / sub-
Safety objectives of Directive
clause(s)
Remarks / Notes
2014/35/EU (Annex I)
of this EN
2. Protection against hazards arising from the electrical equipment
Measures of a technical nature shall be laid down in accordance with point 1, in order to ensure that:
4, 6.1 – 6.11,
2 (a) persons and domestic animals are
9.6, 11.6,
adequately protected against the danger
Annex F,
of physical injury or other harm which
Annex K
might be caused by direct or indirect
contact
4.4.4.2, 9.5,
2 (b) temperatures, arcs or radiation which
9.6, 10.1 -
would cause a danger, are not produced
10.5, 10.101,
4.4, 7.2- 7.7,
2 (c) persons, domestic animals and
9, 12.3, 12.5,
property are adequately protected against
12.6, 13.1,
non-electrical dangers caused by the
13.2, 16.2
electrical equipment which are revealed
by experience
6.7, Annex K
2 (d) the insulation is suitable for
foreseeable conditions
3. Protection against hazards which may be caused by external influences on the electrical
equipment
Technical measures shall be laid down in accordance with point 1, in order to ensure that the electrical
equipment:
7, 8
3 (a) meets the expected mechanical
requirements in such a way that persons,
domestic animals and property are not
endangered
1.4, 6.7.2.2.1,
3 (b) is resistant to non-mechanical
10.5, 10.101,
influences in expected environmental
11.6,
conditions, in such a way that persons,
14.3, 14.8, 15
domestic animals and property are not
endangered
4, 9, 14, 16.1
3 (c) does not endanger persons,
domestic animals and property in
foreseeable conditions of overload

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
IEC 61010-2-010 ®
Edition 4.0 2019-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
GROUP SAFETY PUBLICATION
PUBLICATION GROUPÉE DE SÉCURITÉ

Safety requirements for electrical equipment for measurement, control and

laboratory use –
Part 2-010: Particular requirements for laboratory

equipment for the heating of materials

Exigences de sécurité pour appareils électriques de mesurage, de régulation et

de laboratoire –
Partie 2-010: Exigences particulières pour appareils de laboratoire utilisés pour

l'échauffement des matières
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 19.080; 71.040.20 ISBN 978-2-8322-6502-4

– 2 – IEC 61010-2-010:2019 © IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 6
1 Scope and object . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Tests . 10
5 Marking and documentation . 10
6 Protection against electric shock . 14
7 Protection against mechanical HAZARDS . 16
8 Resistance to mechanical stresses . 16
9 Protection against the spread of fire . 17
10 Equipment temperature limits and resistance to heat . 18
11 Protection against HAZARDS from fluids and solid foreign objects . 19
12 Protection against radiation, including laser sources, and against sonic and
ultrasonic pressure . 20
13 Protection against liberated gases and substances, explosion and implosion . 20
14 Components and subassemblies . 21
15 Prot
...