EN IEC 61557-7:2022

SLOVENSKI STANDARD
01-oktober-2022
Nadomešča:
SIST EN 61557-7:2007
Električna varnost v nizkonapetostnih razdelilnih sistemih izmenične napetosti do
1 kV in enosmerne napetosti do 1,5 kV - Oprema za preskušanje, merjenje ali
nadzorovanje zaščitnih ukrepov - 7. del: Fazno zaporedje (IEC 61557-7:2019)
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. -
Equipment for testing, measuring or monitoring of protective measures - Part 7: Phase
sequence (IEC 61557-7:2019)
Elektrische Sicherheit in Niederspannungsnetzen bis AC 1 000 V und DC 1 500 V -
Geräte zum Prüfen, Messen oder Überwachen von Schutzmaßnahmen - Teil 7: Drehfeld
(IEC 61557-7:2019)
Sécurité électrique dans les réseaux de distribution basse tension de 1 000 V c.a. et 1
500 V c.c. - Dispositifs de contrôle, de mesure ou de surveillance de mesures de
protection - Partie 7: Ordre de phases (IEC 61557-7:2019)
Ta slovenski standard je istoveten z: EN IEC 61557-7:2022
ICS:
17.220.20 Merjenje električnih in Measurement of electrical
magnetnih veličin and magnetic quantities
29.080.01 Električna izolacija na Electrical insulation in
splošno general
29.240.01 Omrežja za prenos in Power transmission and
distribucijo električne energije distribution networks in
na splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61557-7

NORME EUROPÉENNE
EUROPÄISCHE NORM May 2022
ICS 17.220.20; 29.080.01; 29.240.01 Supersedes EN 61557-7:2007
English Version
Electrical safety in low voltage distribution systems up to 1 000 V
a.c. and 1 500 V d.c. - Equipment for testing, measuring or
monitoring of protective measures - Part 7: Phase sequence
(IEC 61557-7:2019)
Sécurité électrique dans les réseaux de distribution basse Elektrische Sicherheit in Niederspannungsnetzen bis AC
tension au plus égale à 1 000 V c.a. et 1 500 V c.c. - 1 000 V und DC 1 500 V - Geräte zum Prüfen, Messen oder
Dispositifs de contrôle, de mesure ou de surveillance de Überwachen von Schutzmaßnahmen - Teil 7: Drehfeld
mesures de protection - Partie 7: Ordre de phases (IEC 61557-7:2019)
(IEC 61557-7:2019)
This European Standard was approved by CENELEC on 2022-04-06. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61557-7:2022 E

European foreword
The text of document 85/683/FDIS, future edition 3 of IEC 61557-7, prepared by IEC/TC 85
"Measuring equipment for electrical and electromagnetic quantities" was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN IEC 61557-7:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-01-06
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-04-06
document have to be withdrawn
This document supersedes EN 61557-7:2007 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61557-7:2019 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61010-1 2010 Safety requirements for electrical EN 61010-1 2010
equipment for measurement, control,
and laboratory use - Part 1: General
requirements
+ A1 (mod) 2016 + A1 2019
IEC 61010-2-030 2017 Safety requirements for electrical EN IEC 61010-2-030 2021
equipment for measurement, control,
and laboratory use - Part 2-030:
Particular requirements for equipment
having testing or measuring circuits
- - + A11 2021
IEC 61010-031 - Safety requirements for electrical EN 61010-031 -
equipment for measurement, control
and laboratory use - Part 031: Safety
requirements for hand-held probe
assemblies for electrical measurement
and test
IEC 61557-1 2019 Electrical safety in low voltage EN IEC 61557-1 2021
distribution systems up to 1 000 V AC
and 1 500 V DC - Equipment for testing,
measuring or monitoring of protective
measures - Part 1: General
requirements
IEC 61557-7 ®
Edition 3.0 2019-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and

1 500 V d.c. – Equipment for testing, measuring or monitoring of protective

measures –
Part 7: Phase sequence
Sécurité électrique dans les réseaux de distribution basse tension au plus

égale à 1 000 V c.a. et 1 500 V c.c. – Dispositifs de contrôle, de mesure ou

de surveillance de mesures de protection –

Partie 7: Ordre de phases
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.20; 29.080.01; 29.240.01 ISBN 978-2-8322-7161-2

– 2 – IEC 61557-7:2019 © IEC 2019
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Requirements . 6
4.1 General . 6
4.2 Indication . 6
4.3 Measuring equipment . 7
4.3.1 General . 7
4.3.2 Portable phase sequence indicator . 7
4.3.3 Test leads for direct contact with live parts and accessories . 7
5 Marking and operating instructions . 8
5.1 Marking . 8
5.2 Operating instructions . 8
6 Tests . 8
6.1 General . 8
6.1.1 Tests – General . 8
6.1.2 Visual display . 8
6.1.3 Audible indication (if applicable) . 8
6.2 Leakage current . 8
6.3 Test of mechanical requirements (type tests) . 9
6.3.1 Mechanical shock test . 9
6.3.2 Test of leads for direct contact with live parts . 9
6.4 Overvoltage . 9
6.5 Test of markings . 9
Annex A (normative) Illustrations for mechanical tests . 10
Annex B (informative) Phase sequence test . 12
B.1 Phase sequence test – Tripolar connection . 12
B.2 Phase sequence test – Sequential bipolar connection . 12
Bibliography . 14

Figure A.1 – Mechanical shock test . 10
Figure A.2 – Drop test . 11
Figure B.1 – Tripolar connection . 12
Figure B.2 – Sequential bipolar connection . 13

IEC 61557-7:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL SAFETY IN LOW VOLTAGE DISTRIBUTION SYSTEMS
UP TO 1 000 V AC AND 1 500 V DC –
EQUIPMENT FOR TESTING, MEASURING OR MONITORING
OF PROTECTIVE MEASURES –
Part 7: Phase sequence
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transp
...