SLOVENSKI STANDARD
SIST EN 61000-4-3:1997/A1:2001
01-marec-2001
Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement
techniques - Radiated, radio-frequency, electromagnetic field immunity test
Electromagnetic compatibility (EMC) -- Part 4-3: Testing and measurement techniques -
Radiated, radio-frequency, electromagnetic field immunity test
Elektromagnetische Verträglichkeit (EMV) -- Teil 4-3: Prüf- und Meßverfahren - Prüfung
der Störfestigkeit gegen hochfrequente elektromagnetische Felder
Compatibilité électromagnétique (CEM) -- Partie 4-3: Techniques d'essai et de mesure -
Essai d'immunité aux champs électromagnétiques rayonnés aux fréquences
radioélectriques
Ta slovenski standard je istoveten z: EN 61000-4-3:1996/A1:1998
ICS:
33.100.20 Imunost Immunity
SIST EN 61000-4-3:1997/A1:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 2 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 3 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 4 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 5 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 6 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 7 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 8 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 9 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 10 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 11 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 12 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 13 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 14 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Page: 15 ----------------------

SIST EN 61000-4-3:1997/A1:2001

---------------------- Pa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC

EN 61000-4-16:2016(Main)

Electromagnetic compatibility (EMC) - Part 4-16: Testing and measurement techniques - Test for immunity to conducted, common mode disturbances in the frequency range 0 Hz to 150 kHz

SIST EN 61000-4-16:2016

IEC 61000-4-16:2015 is available as IEC 61000-4-16:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61000-4-16:2015 relates to the immunity requirements and test methods for electrical and electronic equipment to conducted, common mode disturbances in the range d.c. to 150 kHz. The object of this standard is to establish a common and reproducible basis for testing electrical and electronic equipment with the application of common mode disturbances to power supply, control, signal and communication ports. It has the status of a basic EMC publication in accordance with IEC Guide 107. This second edition cancels and replaces the first edition published in 1998, Amendment 1:2001 and Amendment 2:2009. This edition constitutes a technical revision.

Standard
28 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN 55014-2:2015(Main)

Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 2: Immunity - Product family standard

SIST EN 55014-2:2015

CISPR 14-2:2015 is available as <a href="https://webstore.iec.ch/publication/22136">CISPR 14-2:2015 RLV</a> which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. CISPR 14-2:2015 deals with the electromagnetic immunity of appliances and similar apparatus for household and similar purposes that use electricity, as well as electric toys and electric tools, the rated voltage of the apparatus being not more than 250 V for single-phase apparatus to be connected to phase and neutral, and 480 V for other apparatus. Apparatus may incorporate motors, heating elements or their combination, may contain electric or electronic circuitry, and may be powered by the mains, by transformer, by batteries, or by any other electrical power source. Apparatus not intended for household use, but which nevertheless may require the immunity level, such as apparatus intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard, as far as they are included in CISPR 14-1. In addition, the following are also included in the scope of this standard: - microwave ovens for domestic use and catering; - cooking hobs and cooking ovens, heated by means of r.f. energy; - (single- and multiple-zone) induction cooking appliances; - appliances for personal care equipped with radiators in the range from UV to IR, inclusive (this includes visible light); - power supplies and battery chargers provided with or intended for apparatus within the scope of this standard. This second edition cancels and replaces the first edition published in 1997, Amendment 1:2001 and Amendment 2:2008. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - 5.1: For ESD tests on contacts of plugs and sockets the note ("The 4 kV contact discharge shall be applied to conductive accessible parts. Metallic contacts, such as in battery compartments or in socket outlets, are excluded from this requirement.") saying that no test on contacts is necessary has been removed. The IEC 61000-4-2 includes a detailed description how to deal with ESD on contacts and other surfaces. Also discharge on HCP and VCP is required by the basic standard IEC 61000-4-2. - 5.3 and 5.4: The tables for tests at D.C. power ports according IEC 61000-4-6 are aligned with the generic standards and are the same for 5.3 and 5.4. - 5.3 and 5.4: For EUT with single mains cable and not other cable, the test set-up as shown in Figure 2 shall be used. The set-up as described in Annex F of IEC 61000-4-6:2013 shall not be used. - 5.5: The IEC 61000-4-22 has been introduced as alternative method for testing radiated immunity. - 5.6: No line-to-earth surges are applied to products which do not have provision for connection to earth.

Standard
26 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN 61000-6-3:2007(Main)

Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments

SIST EN 61000-6-3:2007

This part of IEC 61000 for EMC emission requirements applies to electrical and electronic apparatus intended for use in residential, commercial and light-industrial environments. Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No measurement needs to be performed at frequencies where no requirement is specified. This generic EMC emission standard is applicable if no relevant dedicated product or product-family EMC emission standard exists. This standard applies to apparatus intended to be directly connected to a low-voltage public mains network or connected to a dedicated DC source, which is intended to interface between the apparatus and the low-voltage public mains network. This standard applies also to apparatus which is battery operated or is powered by a non-public, but non-industrial, low-voltage power distribution system if this apparatus is intended to be used in the locations described below. The environments encompassed by this standard are residential, commercial and light-industrial locations, both indoor and outdoor. The following list, although not comprehensive, gives an indication of locations that are included: - residential properties, for example houses, apartments; - retail outlets, for example shops, supermarkets; - business premises, for example offices, banks; - areas of public entertainment, for example cinemas, public bars, dance halls; - outdoor locations, for example petrol stations, car parks, amusement and sports centres; - light-industrial locations, for example workshops, laboratories, service centres. Locations that are characterised by being supplied directly at low voltage from the public mains network are considered to be residential, commercial or light-industrial. The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances. The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in residential, commercial and light-industrial locations do not exceed a level which could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements. Requirements are specified for each port considered.

Standard
19 pages
English language
sale 10% off
e-Library read for
1 day
Standard – translation
19 pages
Slovenian language
sale 10% off
e-Library read for
1 day

CLC

EN 61000-2-9:1996(Main)

Electromagnetic compatibility (EMC) - Part 2: Environment - Section 9: Description of HEMP environment - Radiated disturbance

SIST EN 61000-2-9:1997

This section of IEC 61000-2 defines the high-altitude electromagnetic pulse (HEMP) environment that is one of the consequences of a high-altitude nuclear explosion. Those dealing with this subject consider two cases: - high-altitude nuclear explosions; - low-altitude nuclear explosions. For civil systems, the most important case is the high-altitude nuclear explosion. In this case, the other effects of the nuclear explosion: blast, ground shock, thermal and nuclear ionizing radiation are not present at the ground level. However the electromagnetic pulse associated with the explosion may cause disruption of, and damage to, communication, electronic and electric power systems thereby upsetting the stability of modern society. The object of this standard is to establish a common reference for the HEMP environment in order to select realistic stresses to apply to victim equipment for evaluating their performance.

Standard
29 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN 61000-5-5:1996(Main)

Electromagnetic compatibility (EMC) - Part 5: Installation and mitigation guidelines - Section 5: Specification of protective devices for HEMP conducted disturbance

SIST EN 61000-5-5:1997

This part of 61000-5 defines how protective devices for conducted disturbance proposed for HEMP protection shall be specified. It is intended to be used for the harmonization of existing or future specifications issued by protective device manufacturers, electronic equipment manufacturers, administrations and other ultimate buyers. Performance requirements shall be given in future IEC documents. This section covers protective devices currently being used for protection against induced HEMP transients on signal and low voltage power lines (nominal voltage up to 1 kV a.c.). General information can be applied also to high voltage lines. However, in these cases, the additional requirements for the protection levels of existing lightning arresters (especially gapless MO-arresters) are under consideration.

Standard
39 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 62153-4-7:2021(Main)

Metallic cables and other passive components test methods - Part 4-7: Electromagnetic compatibility (EMC) -Test method for measuring of transfer impedance Z_T and screening attenuation a_S or coupling attenuation a_C of connectors and assemblies - Triaxial tube in tube method

SIST EN IEC 62153-4-7:2021

This part of IEC 62153 deals with the triaxial tube in tube method. This triaxial method is suitable to determine the surface transfer impedance and/or screening attenuation and coupling attenuation of mated screened connectors (including the connection between cable and connector) and cable assemblies. This method could also be extended to determine the transfer impedance, coupling or screening attenuation of balanced or multipin connectors and multicore cable assemblies. For the measurement of transfer impedance and screening- or coupling attenuation, only one test set-up is needed.

Standard
61 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 61326-2-3:2021(Main)

Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning

SIST EN IEC 61326-2-3:2021

IEC 61326-2-3:2020 is available as IEC 61326-2-3:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326-2-3:2020 specifies more detailed test configurations, operational conditions and performance criteria for transducers with integrated or remote signal conditioning. This document applies only to transducers characterized by their ability to transform, with the aid of an auxiliary energy source, a non-electric quantity to a process-relevant electrical signal, and to output the signal at one or more PORTS. This document includes transducers for electrochemical and biological measured quantities. The transducers covered by this document can be powered by AC or DC voltage and/or by battery or with internal power supply.

Standard
25 pages
English language
sale 10% off
e-Library read for
1 day
Draft
22 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 61326-2-2:2021(Main)

Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-2: Particular requirements - Test configurations, operational conditions and performance criteria for portable testing, measuring and monitoring equipment used in low-voltage distribution systems

SIST EN IEC 61326-2-2:2021

IEC 61326-2-2:2020 is available as IEC 61326-2-2:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326-2-2:2020 specifies more detailed test configurations, operational conditions and performance criteria for equipment covered by Annex A of IEC 61326-1:2020 which is: - used for testing, measuring or monitoring of protective measures in low-voltage distribution systems, and; - powered by battery and/or from the circuit measured, and - portable. Examples of such EUTs include, but are not limited to, voltage detectors, insulation testers, earth continuity testers, earth resistance testers, leakage current clamps, loop impedance testers, “residual-current-device-testers” (RCD-testers) and phase sequence testers as defined in IEC 61557 (all parts).

Standard
15 pages
English language
sale 10% off
e-Library read for
1 day
Draft
9 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 61326-1:2021(Main)

Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements

SIST EN IEC 61326-1:2021

IEC 61326-1:2020 is available as IEC 61326-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326:2020 specifies requirements for immunity and emissions regarding electro¬magnetic compatibility (EMC) for electrical equipment, operating from a supply or battery of less than 1 000 V AC or 1 500 V DC or from the circuit being measured. Equipment intended for professional, industrial-process, industrial-manufacturing and educational use is covered by this part. It includes equipment and computing devices for - measurement and test; - control; - LABORATORY use; - accessories intended for use with the above (such as sample handling equipment), intended to be used in industrial and non-industrial locations.

Standard
28 pages
English language
sale 10% off
e-Library read for
1 day
Draft
23 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 61326-2-4:2021(Main)

Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-4: Particular requirements - Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC 61557-8 and for equipment for insulation fault location according to IEC 61557-9

SIST EN IEC 61326-2-4:2021

IEC 61326-2-4:2020 is available as IEC 61326-2-4:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326-2-4:2020 specifies more detailed test configurations, operational conditions and performance criteria than IEC 61326-1 for equipment for - insulation monitoring according to IEC 61557-8; - insulation fault location according to IEC 61557-9. This applies to insulation monitoring devices and for equipment for insulation fault location systems permanently or semi-permanently connected to the distribution system.

Standard
18 pages
English language
sale 10% off
e-Library read for
1 day
Draft
15 pages
English language
sale 10% off
e-Library read for
1 day