EN 61936-1:2010/AC:2013

EN 61936-1:2010/AC:2013 is a corrigendum published by CLC. Its full title is "Power installations exceeding 1 kV a.c. - Part 1: Common rules". This standard covers: This part of IEC 61936 provides common rules for the design and the erection of electrical power installations in systems with nominal voltages above 1 kV a.c. and nominal frequency up to and including 60 Hz, so as to provide safety and proper functioning for the use intended. For the purpose of interpreting this standard, an electrical power installation is considered to be one of the following: a) Substation, including substation for railway power supply b) Electrical installations on mast, pole and tower Switchgear and/or transformers located outside a closed electrical operating area c) One (or more) power station(s) located on a single site The installation includes generators and transformers with all associated switchgear and all electrical auxiliary systems. Connections between generating stations located on different sites are excluded. d) The electrical system of a factory, industrial plant or other industrial, agricultural, commercial or public premises The electrical power installation includes, among others, the following equipment: – rotating electrical machines; – switchgear; – transformers and reactors; – converters; – cables; – wiring systems; – batteries; – capacitors; – earthing systems; – buildings and fences which are part of a closed electrical operating area; – associated protection, control and auxiliary systems; – large air core reactor. NOTE In general, a standard for an item of equipment takes precedence over this standard. This standard does not apply to the design and erection of any of the following: – overhead and underground lines between separate installations; – electric railways; – mining equipment and installations; – fluorescent lamp installations; – installations on ships and off-shore installations; – electrostatic equipment (e.g. electrostatic precipitators, spray-painting units); – test sites; – medical equipment, e.g. medical X-ray equipment. This standard does not apply to the design of factory-built, type-tested switchgear for which separate IEC standards exist. This standard does not apply to the requirements for carrying out live working on electrical installations. If not otherwise required in this standard, for low-voltage electrical installations the standard series IEC 60364 applies.

This part of IEC 61936 provides common rules for the design and the erection of electrical power installations in systems with nominal voltages above 1 kV a.c. and nominal frequency up to and including 60 Hz, so as to provide safety and proper functioning for the use intended. For the purpose of interpreting this standard, an electrical power installation is considered to be one of the following: a) Substation, including substation for railway power supply b) Electrical installations on mast, pole and tower Switchgear and/or transformers located outside a closed electrical operating area c) One (or more) power station(s) located on a single site The installation includes generators and transformers with all associated switchgear and all electrical auxiliary systems. Connections between generating stations located on different sites are excluded. d) The electrical system of a factory, industrial plant or other industrial, agricultural, commercial or public premises The electrical power installation includes, among others, the following equipment: – rotating electrical machines; – switchgear; – transformers and reactors; – converters; – cables; – wiring systems; – batteries; – capacitors; – earthing systems; – buildings and fences which are part of a closed electrical operating area; – associated protection, control and auxiliary systems; – large air core reactor. NOTE In general, a standard for an item of equipment takes precedence over this standard. This standard does not apply to the design and erection of any of the following: – overhead and underground lines between separate installations; – electric railways; – mining equipment and installations; – fluorescent lamp installations; – installations on ships and off-shore installations; – electrostatic equipment (e.g. electrostatic precipitators, spray-painting units); – test sites; – medical equipment, e.g. medical X-ray equipment. This standard does not apply to the design of factory-built, type-tested switchgear for which separate IEC standards exist. This standard does not apply to the requirements for carrying out live working on electrical installations. If not otherwise required in this standard, for low-voltage electrical installations the standard series IEC 60364 applies.

EN 61936-1:2010/AC:2013 is classified under the following ICS (International Classification for Standards) categories: 29.020 - Electrical engineering in general; 29.080.01 - Electrical insulation in general. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 61936-1:2010/AC:2013 has the following relationships with other standards: It is inter standard links to EN 61936-1:2010/AC:2012, EN IEC 61936-1:2021, EN 61936-1:2010. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN 61936-1:2010/AC:2013 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.