iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12756:2000

(Main)

Mechanical seals - Principal dimensions, designation and material codes

Mechanical seals - Principal dimensions, designation and material codes

This European Standard defines the principal dimensions for the internal installation of single and multiple mechanical seals with (rotating) spring units into the pump sealing cavity according to ISO 3069 as minimum cavity dimensions as typical for centrifugal pumps in accordance with EN 22858 and EN 733. It also gives the seal designations and material codes to be used.

Gleitringdichtungen - Hauptmaße, Bezeichnung und Werkstoffschlüssel

Diese Europäische Norm enthält die Hauptmaße für den Einbau von innenliegenden Einzel und Mehrfach-Gleitringdichtungen mit umlaufendem Federteilin den Wellendichtungsraum nach ISO 3069 als Mindest-Einbauraumabmessungen, wie diese typisch für Kreiselpumpen nach EN 22858 und EN 733 sind, und legt deren Bezeichnung und Werkstoffschlüssel fest.

Garnitures mécaniques d'étanchéité - Dimensions principales, désignation et codes matériaux

Cette norme européenne définit les dimensions principales de montage des garnitures mécaniques simples et doubles à bague élastique tournante dans des logements de pompes conformes à l'ISO 3069, de dimensions minimales caractéristiques pour pompes centrifuges du type indiqué dans les EN    22858 et EN 733. Elle donne également les désignations des garnitures d'étanchéité et les codes matériaux à utiliser.

Mechanical seals - Principal dimensions, designation and material codes

General Information

Status
Published
Publication Date
12-Dec-2000
Withdrawal Date
01-Jul-2001
ICS
21.140 - Seals, glands
Technical Committee
CEN/TC 197 - Pumps
Drafting Committee
CEN/TC 197 - Pumps
Current Stage
9093 - Decision to confirm - Review Enquiry
Start Date
25-Jan-2011
Completion Date
25-Jan-2011
Ref Project
SIST EN 12756:2001 - Mechanical seals - Principal dimensions, designation and material codes

Buy Standard

EN 12756:2001EN 12756:2001
PreviousNext
Standard
EN 12756:2001
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Mechanical seals - Principal dimensions, designation and material codesGleitringdichtungen - Hauptmaße, Bezeichnung und WerkstoffschlüsselGarnitures mécaniques d'étanchéité - Dimensions principales, désignation et codes matériauxMechanical seals - Principal dimensions, designation and material codes21.140T
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 16752:2015(Main)
Centrifugal pumps - Test procedure for seal packings
SIST EN 16752:2015

This European Standard gives details of a test procedure for packings to be used to seal the stuffing boxes of centrifugal pumps. It gives provisions on the design of test equipment, standard test parameters and reporting criteria. It does not specify performance criteria which should be agreed between supplier and customer, but does define 3 tightness classes.
When necessary, this European Standard is also applicable to packings used on other rotary equipment such as mixers and agitators.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16752:2015(Main)
Centrifugal pumps - Test procedure for seal packings
SIST EN 16752:2015

This European Standard gives details of a test procedure for packings to be used to seal the stuffing boxes of centrifugal pumps. It gives provisions on the design of test equipment, standard test parameters and reporting criteria. It does not specify performance criteria which should be agreed between supplier and customer, but does define 3 tightness classes.
When necessary, this European Standard is also applicable to packings used on other rotary equipment such as mixers and agitators.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21049:2004(Main)
Pumps - Shaft sealing systems for centrifugal and rotary pumps (ISO 21049:2004)
SIST EN ISO 21049:2005

ISO 21049:2004 specifies requirements and gives recommendations for sealing systems for centrifugal and rotary pumps used in the petroleum, natural gas and chemical industries. It is applicable mainly for hazardous, flammable and/or toxic services where a greater degree of reliability is required for the improvement of equipment availability and the reduction of both emissions to the atmosphere and life-cycle sealing costs. It covers seals for pump shaft diameters from 20 mm (0,75 in) to 110 mm (4,3 in).
ISO 21049:2004 is also applicable to seal spare parts and can be referred to for the upgrading of existing equipment. A classification system for the seal configurations covered by ISO 21049:2004 into categories, types, arrangements and orientations is provided.

  • Standard
    197 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 751-2:1996(Main)
Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds
SIST EN 751-2:1997

This European Standard specifies requirements and test methods for non-hardening sealing materials (hereafter referred to as jointing compounds) suitable for sealing threaded metallic joints such as those specified in ISO 7-1. These jointing compounds are for use in contact with 1st family gases (town gas), 2nd family gases (natural gas) and 3rd family gases (liquefied petroleum gases (LPG) not including LPG in the liquid form) and hot water of heating systems (Class A), in gas appliances and their auxiliary equipment (Class B) as well as in LPG storage (Class C) according to table 1.  Anaerobic jointing compounds are covered by EN 751-1, non-hardening sealing materials in the form of PTFE-tapes are covered by EN 751-3.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 751-1:1996(Main)
Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds
SIST EN 751-1:1997

This European Standard specifies requirements and test methods for anaerobic jointing compounds (hereafter referred to as "jointing compounds") suitable for sealing threaded metallic joints such as those specified in ISO 7-1. These jointing compounds are for use in contact with 1st family gases (town gas), 2nd family gases (natural gas) and 3rd family gases (liquefied petroleum gases (LPG) not including LPG in the liquid form) and hot water of heating systems.  [The scope of the complete standard includes a table.]

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9222-1:1995(Main)
Technical drawings - Seals for dynamic application - Part 1: General simplified representation (ISO 9222-1:1989)
SIST EN ISO 9222-1:1998

This method indicates only essential features ans should be used when it is not necessary to show the exact shape and details of the seals, for example in assembly drawings. The degree of simplification depends on the kind of object represented, the scale of the drawing and the purpose of documentation. ISO 9222-2 deals with the detailed simplified representation.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9222-2:1994(Main)
Technical drawings - Seals of dynamic application - Part 2: Detailed simplified representation (ISO 9222-2:1989)
SIST EN ISO 9222-2:1998

In contrast to the general simplified representation of part 1, this method shows more details of a seal, for example the configuration of lips. It should also be used when it is not necessary to show the exact shape and details of the seals, for example in assembly drawings. Elements and examples of this representation mode are given in tables and figures.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 21049(Main)
Pumps - Shaft-sealing systems for centrifugal and rotary pumps (ISO/DIS 21049:2010)
oSIST prEN ISO 21049:2010

2018-06-15 Project abandoned as ISO abandoned the project.

  • Draft
    293 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1888-3:2024(Main)
Child care articles - Wheeled child conveyances - Part 3: Pushchairs intended for leisure sport activities
kSIST FprEN 1888-3:2024

This document specifies the safety requirements of pushchairs when used for running/jogging or skating (excluding ice skating), intended for the transport of one or two children up to 15 or 22 kg each.
Pushchairs intended to transport the carer while pushing (e.g. the combination of longboard and stroller) are excluded from the scope of this document.
This document applies in conjunction with and in addition to the European standards EN 1888 1:2018+A1:2022 or EN 1888-2:2018+A1:2022 and it cannot be used separately.
If the product has several functions or can be converted into another function, the relevant European standards apply to it.

  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15877-1:2024(Main)
Railway applications - Markings of railway vehicles - Part 1: Freight wagons
kSIST FprEN 15877-1:2024

This document specifies the markings on heavy rail freight wagons, or parts of heavy rail freight wagons, relating to their technical, operational and maintenance characteristics. It specifies the characteristics of these markings, the requirements pertaining to their presentation, their shape and position on a rail vehicle and their meaning. Some markings are accompanied with (a) note(s), where appropriate.
Tank manufacturers’ design criteria, test and product specification plates have not been considered in this document as they are specified in EN 12561 1:2011.
Where fully specified in RID [14] dangerous goods markings have not been considered in this document (dimensions, colour, location and form). Where markings are not fully specified in RID they are included in this document.

  • Draft
    126 pages
    English language
    sale 10% off
    e-Library read for
    1 day