EN ISO 11064-2:2000

SLOVENSKI STANDARD
SIST EN ISO 11064-2:2003
01-februar-2003
(UJRQRPVNRQDþUWRYDQMHNUPLOQLKFHQWURYGHO1DþHOD]DXUHGLWHYNRQWUROQHJD
SURVWRUD,62
Ergonomic design of control centres - Part 2: Principles for the arrangement of control
suites (ISO 11064-2:2000)
Conception ergonomique des centres de commande - Partie 2: Principes pour
l'aménagement de la salle de commande et de ses annexes (ISO 11064-2:2000)
Ta slovenski standard je istoveten z: EN ISO 11064-2:2000
ICS:
13.180 Ergonomija Ergonomics
25.040.10 9HþRSHUDFLMVNLVWURML Machining centres
SIST EN ISO 11064-2:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11064-2:2003

---------------------- Page: 2 ----------------------

SIST EN ISO 11064-2:2003
EUROPEAN STANDARD
EN ISO 11064-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2000
ICS 13.180; 25.040.10
English version
Ergonomic design of control centres - Part 2: Principles for the
arrangement of control suites (ISO 11064-2:2000)
Conception ergonomique des centres de commande - Ergonomische Gestaltung von Leitzentralen - Teil 2:
Partie 2: Principes pour l'aménagement de la salle de Grundsätze für die Anordnung von Warten mit
commande et de ses annexes (ISO 11064-2:2000) Nebenräumen (ISO 11064-2:2000)
This European Standard was approved by CEN on 15 December 2000.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2000 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11064-2:2000 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11064-2:2003
Page 2
EN ISO 11064-2:2000
Corrected 2001-04-04
Foreword
The text of the International Standard ISO 11064-2:2000 has been prepared by Technical Committee
ISO/TC 159 "Ergonomics" in collaboration with Technical Committee CEN/TC 122 "Ergonomics", the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2001, and conflicting national standards shall be
withdrawn at the latest by June 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,
Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 11064-2:2000 was approved by CEN as a European Standard
without any modification.
NOTE: Normative references to International Standards are listed in annex ZA (normative).

---------------------- Page: 4 ----------------------

SIST EN ISO 11064-2:2003
Page 3
EN ISO 11064-2:2000
Annex ZA (normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other publications.
These normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply
to this European Standard only when incorporated in it by amendment or revision. For undated references
the latest edition of the publication referred to applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated by
(mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 6385 1990 Ergonomic principles of the design of ISO 6385 1981
work systems
ISO 11064-1 2000 Ergonomic design of control centres - ISO 11064-1 2000
Part 1: Principles for the design of
control centres
ISO 11064-3 1999 Ergonomic design of control centres
...