EN 15189:2006

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Litoželezne cevi, fitingi in pribor - Zunanja poliuretanska prevleka cevi - Zahteve in metode preskušanjaRohre, Formstücke und Zubehör aus duktilem Gusseisen - Polyurethanumhüllung von Rohren - Anforderungen und PrüfverfahrenTuyaux, raccords et accessoires en fonte ductile - Revetement extérieur polyuréthanne des tuyaux - Exigences et méthodes d'essaiDuctile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods77.140.75Jeklene cevi in cevni profili za posebne nameneSteel pipes and tubes for specific useICS:Ta slovenski standard je istoveten z:EN 15189:2006SIST EN 15189:2007en01-april-2007SIST EN 15189:2007SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15189November 2006ICS 23.040.01; 25.220.60 English VersionDuctile iron pipes, fittings and accessories - Externalpolyurethane coating for pipes - Requirements and test methodsTuyaux, raccords et accessoires en fonte ductile -Revêtement extérieur polyuréthanne des tuyaux -Exigences et méthodes d'essaiRohre, Formstücke und Zubehör aus duktilem Gusseisen -Polyurethanumhüllung von Rohren - Anforderungen undPrüfverfahrenThis European Standard was approved by CEN on 11 September 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15189:2006: ESIST EN 15189:2007

Quality assurance.14 Annex B (normative)
Coating application process.16 Annex C (informative)
Packaging.18 Bibliography.19
EN ISO 62, Plastics - Determination of water absorption (ISO 62:1999) EN ISO 527-3, Plastics - determination of tensile properties – Part 3: Test conditions for films and sheets (ISO 527-3:1995) EN ISO 868, Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003)
EN ISO 4624, Paints and varnishes; Pull-off test for adhesion (ISO 4624:2002) EN ISO 8501–1, Preparation of steel substrates before application of paints and related products – Visual assessment of surface cleanliness – Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1:1988) EN ISO 8503–1, Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:1988) SIST EN 15189:2007

absence of holidays in a high voltage test under defined test conditions 3.6 polyurethane coating factory applied coating which consists of
polyurethane on the outside of the pipe barrel and external socket
Key 1 Gasket seat 2 Socket entrance 3 Socket face 4 External socket 5 Pipe barrel 6 Spigot end Figure 1 — Location of the defined pipe areas Pipe ends such as the spigot end, the socket face, the socket entrance and gasket seat may be coated differently
(see 5.3) 3.7 specific coating resistance surface related electric resistance of the coating perpendicular to the pipe wall SIST EN 15189:2007

test which is done once and is repeated according to a schedule or after a relevant change of coating material
and/or coating supplier or change in process application 3.9 routine test test carried out to control the manufacturing process with a frequency defined by the manufacturer 4 Ordering information The following information shall be obtained by the manufacturer. Ductile iron pipes according to EN 545, EN 598 or EN 969, but externally coated in accordance with this European Standard shall be specified in the purchaser enquiry and order by reference to this standard. EXAMPLE: 5 000 m of ductile iron pipe DN 300 according to EN 545; external polyurethane coating according to EN 15189. The manufacturer shall obtain from the purchaser the type of coating to be used for pipe ends (see 5.3). 5 Technical Requirements 5.1 Surface preparation Prior to application of the polyurethane coating, the surface of the pipes shall be technically clean, free of rust, loose constituent materials, dirt, oil, grease and moisture. In cold weather, or anytime when moisture tends to condense on the surface of the pipe, the pipe shall be uniformly warmed for a sufficient time to dry the pipe prior to cleaning. The pipe temperature shall be maintained at at least 5 °C above the dew point. The surface shall be prepared by grit blasting and be in compliance with level Sa 2.5 of EN ISO 8501-1. The surface roughness Ra, in accordance with EN ISO 8503-1, shall be at least 10 micrometers which is equivalent to an anchored profile, Rz of 50 micrometers or higher if required by the coating material provider or manufacturer. 5.2 Finished polyurethane coating 5.2.1 Appearance and continuity The polyurethane coating shall be:  uniform in colour, except the spigot and the socket which may be of a different colour for permitted marking;  uniform appearance and smoothness except for admissible repairs;  free of visible defects (pinholes, bubbles, blisters, wrinkles, cracks or voids). Slight superficial variations of colour or brilliance, due to repairs or prolonged exposure to sunlight or contact with other pipes are permissible. SIST EN 15189:2007

5.7 Hardness When assessed by testing in accordance to EN ISO 868 the hardness of the polyurethane coating shall be at a minimum 70 Shore D. 5.8 Adhesion Adhesion shall be at least 8 MPa when tested in accordance with 7.1.9. 6 Performance Requirements 6.1 Chemical resistance The chemical resistance is determined by the change in weight of the polyurethane coating. When tested in accordance to 7.2.1, the weight increase and weight loss shall meet the requirements given in Table 1 when compared to the original weight. SIST EN 15189:2007

%
%
Immersion test
EN ISO 62 method 2
7.2.1.1
Less than 15 % weight increase Less than 2 % weight loss Mass change in 10 % sulphuric acid, 100 days at 50 °C subsequent drying
...