EN ISO 10380:2012

SLOVENSKI STANDARD
01-april-2013
1DGRPHãþD
SIST EN ISO 10380:2004
&HYRYRG9DORYLWHNRYLQVNHFHYLLQFHYQLSULNOMXþNL,62
Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2012)
Rohrleitungen - Gewellte Metallschläuche und Metallschlauchleitungen (ISO
10380:2012)
Tuyauteries - Tuyaux et tuyauteries métalliques flexibles onduleux (ISO 10380:2012)
Ta slovenski standard je istoveten z: EN ISO 10380:2012
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 10380
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2012
ICS 23.040.70 Supersedes EN ISO 10380:2003
English Version
Pipework - Corrugated metal hoses and hose assemblies (ISO
10380:2012)
Tuyauteries - Tuyaux et tuyauteries métalliques flexibles Rohrleitungen - Gewellte Metallschläuche und
onduleux (ISO 10380:2012) Metallschlauchleitungen (ISO 10380:2012)
This European Standard was approved by CEN on 30 September 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10380:2012: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 10380:2012) has been prepared by Technical Committee CEN/TC 342 “Metal hoses,
hose assemblies, bellows and expansion joints", the secretariat of which is held by SNV, in collaboration with
Technical Committee ISO/TC 5 “Ferrous metal pipes and metallic fittings".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the
latest by April 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10380:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
INTERNATIONAL ISO
STANDARD 10380
Third edition
2012-10-01
Pipework — Corrugated metal hoses and
hose assemblies
Tuyauteries — Tuyaux et tuyauteries métalliques flexibles onduleux
Reference number
ISO 10380:2012(E)
©
ISO 2012
ISO 10380:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

ISO 10380:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Design requirements . 4
4.1 General . 4
4.2 Nominal sizes, DN . 5
4.3 Overall length, l . 6
O
4.4 Hose design . 6
4.5 Materials . 6
4.6 Braiding . 7
4.7 Pressure . 9
4.8 Temperature . 9
4.9 Corrosion .10
4.10 Cleanliness . 11
4.11 Electrical conductivity . 11
4.12 Flow velocity . 11
4.13 Additional protection .12
4.14 Hose joining .14
4.15 Attachment of end fittings to hose .15
4.16 Design parameters for corrugated metal hoses and metal hose assemblies .16
5 Performance requirements and tests .16
5.1 General .16
5.2 Leaktightness .17
5.3 Pressure resistance .17
5.4 Elongation .18
5.5 Burst pressure .18
5.6 Pliability .19
5.7 Fatigue .21
5.8 Electrical conductivity .26
6 Evaluation of conformity .26
6.1 Declaration of products relating to the conformity assessment method .26
6.2 General .27
6.3 Initial type testing .27
6.4 Subsequent type testing .28
6.5 Factory production control (FPC) .28
6.6 Final assessment .30
7 Installation instructions, packaging, designation and marking .31
7.1 Installation instructions .31
7.2 Packaging .31
7.3 Designation .31
7.4 Marking .32
Annex A (normative) Equivalent European material specifications .33
Bibliography .36
ISO 10380:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10380 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 342, Metal hoses, hose assemblies, bellows and expansion joints, in collaboration with ISO Technical
Committee TC 5, Ferrous metal pipes and metallic fittings, Subcommittee SC 11, Metal hoses and expansion
joints, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 10380:2003), which has been technically revise
...