EN ISO 10240:2024

SLOVENSKI STANDARD
01-junij-2024
Mala plovila - Priročnik za uporabo (ISO 10240:2022)
Small craft - Owner's manual (ISO 10240:2022)
Kleine Wasserfahrzeuge - Eignerhandbuch (ISO 10240:2022)
Petits navires - Manuel du propriétaire (ISO 10240:2022)
Ta slovenski standard je istoveten z: EN ISO 10240:2024
ICS:
47.080 Čolni Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 10240
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2024
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 10240:2020
English Version
Small craft - Owner's manual (ISO 10240:2022)
Petits navires - Manuel du propriétaire (ISO Kleine Wasserfahrzeuge - Eignerhandbuch (ISO
10240:2022) 10240:2022)
This European Standard was approved by CEN on 20 March 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10240:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4

European foreword
This document (EN ISO 10240:2024) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with Technical Committee CEN/TC 464 “Small Craft” the secretariat of which is
held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2024, and conflicting national standards shall
be withdrawn at the latest by April 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10240:2020.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 10240:2022 has been approved by CEN as EN ISO 10240:2024 without any modification.

Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex 1 and Annex II of
Directive 2013/53/EU
Requirements of Clause(s)/sub-clause(s) Remarks/Notes
of this EN
Directive 2013/53/EU
Annex I.A.2.5 – Owner’s Manual Clause 4(except 4.4), 5( except
5.3(l) ,5.7.3, 5.9)
Table ZA.2 — Applicable European Standard to confer presumption of conformity as described
in this Annex ZA
Column 1 Reference Column 2 Column 3 Column 4
in Clause 2 International
Title Corresponding
Standard Edition
European Standard
Edition
ISO 6185-1:2001 ISO 6185-1:2001 Inflatable boats — Part 1: EN ISO 6185-1:2018
Boats with a maximum motor
power rating of 4,5 kW
ISO 6185-2:2001 ISO 6185-2:2001 Inflatable boats — Part 2: EN ISO 6185-2:2018
Boats with a maximum motor
power rating of 4,5 kW to 15
kW inclusive
ISO 6185-3:2014 ISO 6185-3:2014 Inflatable boats — Part 3: EN ISO 6185-4:2018
Boats with a hull length less
than 8 m with a motor rating
of 15 kW and greater
ISO 6185-4:2011 ISO 6185-4:2011 Inflatable boats — Part 4: EN ISO 6185-4:2018
Boats with a hull length of
between 8 m and 24 m with a
motor power rating of 15 kW
and greater
ISO 8099-1:2018 ISO 8099-1:2018 Waste systems — Part 1: EN ISO 8099-2:2018
Waste water retention
ISO 8666:2020 ISO 8666:2020 Small craft - Principal data EN ISO 8666:2020
EN ISO
8666:2020/A11:2021
ISO 8999:2001 ISO 8999:2001 Reciprocating internal None
combustion engines —
For applicable standard
Graphical symbols
edition see Column 2
ISO 9094:2015 ISO 9094:2015 Fire protection EN ISO 9094:2017
ISO 10239:2014 ISO 10239:2014 Liquefied petroleum gas (LPG) EN ISO 10239:2017
systems
ISO 11105:2020 ISO 11105:2020 Ventilation of petrol engine EN ISO 11105:2020
and/or petrol tank
compartments
ISO 11192:2005 ISO 11192:2005 Graphical symbols EN ISO 1192:2018
ISO 11547:1994 ISO 11547:1994 Start-in-gear protection EN ISO 11547:2018
ISO 11592-1:2016 ISO 11592-1:2016 Determination of maximum EN ISO 11592-1:2016
propulsion power rating using
manoeuvring speed — Part 1:
Craft with a length of hull less
than 8 m
ISO 11592-2:2021 ISO 11592-2:2021 Determination of maximum EN ISO 11592-2:2021
propulsion power rating using
manoeuvring speed — Part 2:
Craft with a length of hull
between 8 m and 24 m
ISO 12217-1:2015 ISO 12217-1:2015 Stability and buoyancy EN ISO 12217-1:2017
assessment and categorization
— Part 1: Non-sailing boats of
hull length greater than or
equal to 6 m
ISO 12217-2:2015 ISO 12217-2:2015 Stability and buoyancy EN ISO 12217-2:2017
assessment and categorization
— Part 2: Sailing boats of hull
length greater than or equal to
6 m
ISO 12217-3:2015 ISO 12217-3:2015 Stability and buoyancy EN ISO 12217-3:2017
assessment and categorization
— Part 3: Boats of hull length
less than 6 m
ISO 14946:2021 ISO 14946:2021 Maximum load capacity EN ISO 14946:2021
ISO 15085:2003/ Amd
ISO 15085:2003 Man-overboard prevention EN ISO 15085:2003
2:2017 and recovery / With
ISO 15085:2003/ EN ISO
Amendment 2
Amd 2:2017 15085:2003+A2:2018
ISO 16315:2016 ISO 16315:2016 Electric propulsion system EN ISO 16315:2016
ISO 80000-1:2009 ISO 80000-1:2009 Quantities and units — Part 1: EN ISO 80000-1:2013
General
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
The documents listed in the Column 1 of Table ZA.2, in whole or in part, are normatively referenced in
this document, i.e. are indispensable for its application. The achievement of the presumption of
conformity is subject to the application of the edition of Standards as listed in Column 4 or, if no
European Standard Edition exists, the International Standard Edition given in Column 2 of Table ZA.2.

INTERNATIONAL ISO
STANDARD 10240
Fourth edition
2022-11
Small craft — Owner's manual
Petits navires — Manuel du propriétaire
Reference number
ISO 10240:2022(E)
ISO 10240:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 10240:2022(E)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 General requirements . 2
4.1 Information required . . 2
4.2 Format . 2
4.3 Units and definitions . 3
4.4 Illustrations . 3
5 Content of owner’s manual .3
5.1 General . 3
5.2 Introduction to the manual . 3
5.3 General information and craft data . 3
5.4 Maximum number of persons . 6
5.5 Loading . 6
5.6 Engine information . 7
5.7 Information connected with the risk of flooding and stability . 7
5.7.1 General . 7
5.7.2 Openings in the hull .
...