EN 1999-1-4:2007/A1:2011
(Amendment)Eurocode 9: Design of aluminium structures - Part 1-4: Cold-formed structural sheeting
Eurocode 9: Design of aluminium structures - Part 1-4: Cold-formed structural sheeting
(1)P EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. The execution of aluminium structures made of cold-formed sheeting is covered in EN 1090-3.
NOTE The rules in this part complement the rules in other parts of EN 1999-1.
(2) Methods are also given for stressed-skin design using aluminium sheeting as a structural diaphragm.
(3) This part does not apply to cold-formed alumi¬nium profiles like C-, Z- etc profiles nor cold-formed and welded circular or rectangular hollow sections.
(4) EN 1999-1-4 gives methods for design by calculation and for design assisted by testing. The methods for the design by calculation apply only within stated ranges of material properties and geometrical properties for which sufficient experience and test evidence is available. These limitations do not apply to design by testing.
(5) EN 1999-1-4 does not cover load arrangement for loads during execution and main-tenance.
Eurocode 9: Bemessung und Konstruktion von Aluminiumtragwerken - Teil 1-4: Kaltgeformte Profiltafeln
Eurocode 9 - Calcul des structures en aluminium - Partie 1-4: Tôles de structure formées à froid
Evrokod 9: Projektiranje konstrukcij iz aluminijevih zlitin - 1-4. del: Hladno oblikovane konstrukcijske pločevine
EN 1999 se uporablja na področju projektiranja zgradb in gradbeništva, ter gradbenih objektov iz aluminija. Je v skladu z načeli in zahtevami za varnost in uporabnost objektov, osnovo njihovega projektiranja in preverjanja, ki so podani v EN 1990 – Osnove projektiranja. EN 1999 se ukvarja samo z zahtevami glede odpornosti, uporabnosti, trajnosti in požarne odpornosti aluminijevih konstrukcij. Drugih zahtev, npr. glede toplotne ali zvočne izolacije, ne obravnava. EN 1999 je namenjen uporabi v povezavi z: - EN 1990 "Osnove projektiranja", - EN 1991 "Vplivi na konstrukcije", - evropski standardi za gradbene izdelke, ki se nanašajo na aluminijeve konstrukcije, - EN 1090-1: Izvedba jeklenih in aluminijastih konstrukcij, – prvi del: Zahteve za ugotavljanje skladnosti sestavnih delov konstrukcij, - EN 1090-3: Izvedba jeklenih in aluminijastih konstrukcij – tretji del: Tehnične zahteve za aluminijaste konstrukcije EN 1999 je razdeljen v pet delov: EN 1999-1-1 Projektiranje konstrukcij iz aluminijevih zlitin: Splošna pravila za konstrukcije. EN 1999-1-2 Projektiranje konstrukcij iz aluminijevih zlitin: Projektiranje požarnovarnih konstrukcij. EN 1999-1-3 Projektiranje konstrukcij iz aluminijevih zlitin: Konstrukcije občutljive na utrujenost. EN 1999-1-4 Projektiranje konstrukcij iz aluminijevih zlitin: Hladno oblikovane konstrukcijske pločevine. EN 1999-1-5 Projektiranje konstrukcij iz aluminijevih zlitin: Lupinaste konstrukcije.
General Information
- Status
- Withdrawn
- Publication Date
- 30-Aug-2011
- Withdrawal Date
- 20-Jan-2026
- Technical Committee
- CEN/TC 250 - Structural Eurocodes
- Drafting Committee
- CEN/TC 250/SC 9 - Eurocode 9: Design of aluminium structures
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 22-Mar-2023
- Completion Date
- 28-Jan-2026
Relations
- Effective Date
- 29-Mar-2023
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 10-Jul-2010
Get Certified
Connect with accredited certification bodies for this standard
ICC Evaluation Service
Nonprofit organization that performs technical evaluations of building products.
Aboma Certification B.V.
Specialized in construction, metal, and transport sectors.
BBA (British Board of Agrément)
UK construction product certification.
Sponsored listings
Frequently Asked Questions
EN 1999-1-4:2007/A1:2011 is a amendment published by the European Committee for Standardization (CEN). Its full title is "Eurocode 9: Design of aluminium structures - Part 1-4: Cold-formed structural sheeting". This standard covers: (1)P EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. The execution of aluminium structures made of cold-formed sheeting is covered in EN 1090-3. NOTE The rules in this part complement the rules in other parts of EN 1999-1. (2) Methods are also given for stressed-skin design using aluminium sheeting as a structural diaphragm. (3) This part does not apply to cold-formed alumi¬nium profiles like C-, Z- etc profiles nor cold-formed and welded circular or rectangular hollow sections. (4) EN 1999-1-4 gives methods for design by calculation and for design assisted by testing. The methods for the design by calculation apply only within stated ranges of material properties and geometrical properties for which sufficient experience and test evidence is available. These limitations do not apply to design by testing. (5) EN 1999-1-4 does not cover load arrangement for loads during execution and main-tenance.
(1)P EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. The execution of aluminium structures made of cold-formed sheeting is covered in EN 1090-3. NOTE The rules in this part complement the rules in other parts of EN 1999-1. (2) Methods are also given for stressed-skin design using aluminium sheeting as a structural diaphragm. (3) This part does not apply to cold-formed alumi¬nium profiles like C-, Z- etc profiles nor cold-formed and welded circular or rectangular hollow sections. (4) EN 1999-1-4 gives methods for design by calculation and for design assisted by testing. The methods for the design by calculation apply only within stated ranges of material properties and geometrical properties for which sufficient experience and test evidence is available. These limitations do not apply to design by testing. (5) EN 1999-1-4 does not cover load arrangement for loads during execution and main-tenance.
EN 1999-1-4:2007/A1:2011 is classified under the following ICS (International Classification for Standards) categories: 91.010.30 - Technical aspects; 91.080.10 - Metal structures; 91.080.17 - Aluminium structures; 93.020 - Earthworks. Excavations. Foundation construction. Underground works. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 1999-1-4:2007/A1:2011 has the following relationships with other standards: It is inter standard links to EN 1999-1-4:2023, EN 1996-1-1:2005+A1:2012, EN 1991-1-7:2006, EN 1999-1-4:2007. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 1999-1-4:2007/A1:2011 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2012
1DGRPHãþD
SIST EN 1999-1-4:2007
(YURNRG 3URMHNWLUDQMHNRQVWUXNFLML]DOXPLQLMHYLK]OLWLQGHO +ODGQR
REOLNRYDQHNRQVWUXNFLMVNHSORþHYLQH
Eurocode 9: Design of aluminium structures - Part 1-4: Cold-formed structural sheeting
Eurocode 9: Bemessung und Konstruktion von Aluminiumtragwerken - Teil 1-4:
Kaltgeformte Profiltafeln
Eurocode 9 - Calcul des structures en aluminium - Partie 1-4: Tôles de structure formées
à froid
Ta slovenski standard je istoveten z: EN 1999-1-4:2007/A1:2011
ICS:
91.010.30 7HKQLþQLYLGLNL Technical aspects
91.080.10 Kovinske konstrukcije Metal structures
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 1999-1-4:2007/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2011
ICS 91.010.30; 91.080.10
English Version
Eurocode 9: Design of aluminium structures - Part 1-4: Cold-
formed structural sheeting
Eurocode 9 - Calcul des structures en aluminium - Partie 1- Eurocode 9: Bemessung und Konstruktion von
4: Tôles de structure formées à froid Aluminiumtragwerken - Teil 1-4: Kaltgeformte Profiltafeln
This amendment A1 modifies the European Standard EN 1999-1-4:2007; it was approved by CEN on 8 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1999-1-4:2007/A1:2011: E
worldwide for CEN national Members.
SIS
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...