91.080.17 - Aluminium structures

This document gives guidelines and recommendations for the general principles of design appropriate to articles to be hot dip galvanized after fabrication (e.g. in accordance with ISO 1461) for the corrosion protection of, for example, articles that have been manufactured in accordance with EN 1090-2.
This document does not apply to hot dip galvanized coatings applied to continuous wire or sheet (e.g. to EN 10346).

This European Standard specifies requirements for the execution of aluminium structural components and structures made from:
a)   rolled sheet, strip and plate;
b)   extrusions;
c)   cold drawn rod, bar and tube;
d)   forgings;
e)   castings.
NOTE 1   The execution of structural components is referred to as manufacturing, in accordance with EN 1090-1.
This European Standard specifies requirements independent of the type and shape of the aluminium structure, and this European Standard is applicable to...view more

This document specifies requirements for the execution of aluminium structural components and structures made from:
a)   rolled sheet, strip and plate;
b)   extrusions;
c)   cold drawn rod, bar and tube;
d)   forgings;
e)   castings.
NOTE 1   The execution of structural components is referred to as manufacturing, in accordance with EN 1090-1.
This document specifies requirements independent of the type and shape of the aluminium structure, and this document is applicable to structures under predomina...view more

This Standard defines the requirements for the manufacture of thingauge cold-formed steel elements, the execution of structures made from such elements (e.g. roofs, coverings, walls, floors, ceilings and purlins) under predominantly static loading conditions and corresponding requirements to documentation. It does cover products of construction class I and II according to EN 1993-1-3 used in structures

This European Standard specifies requirements for the execution, i.e. the manufacture and the installation, of cold-formed structural steel members and sheeting and cold-formed structures for roof, ceiling, floor, wall and cladding applications.
This European Standard applies to structures designed according to the EN 1993 series.
This European Standard applies to structural members and sheeting to be designed according to EN 1993 1 3.
This European Standard may be used for structures designe...view more

The standard defines the requirements for the manufacture of thin-gauge cold-formed aluminium elements, the execution of structures made from such elements (e.g. roofs, coverings, walls, florors, ceilings and purlins) under predominantly static loading conditions and corresponding requirements to documentation

ISO 14713-1:2017 provides guidelines and recommendations regarding the general principles of design which are appropriate for articles to be zinc coated for corrosion protection and the level of corrosion resistance provided by zinc coatings applied to iron or steel articles, exposed to a variety of environments. Initial protection is covered in relation to
- available standard processes,
- design considerations, and
- environments for use.
ISO 14713-1:2017 applies to zinc coatings applied b...view more

This European Standard specifies requirements for the execution i.e. the manufacture and the installation of cold-formed structural aluminium components made from profiled sheeting for roof, ceiling, floor and wall applications under predominately static loading conditions or seismic loading conditions and their documentation. It does cover products of structural class I and II according to EN 1999-1-4 used in structures.
Structural elements are understood here to mean profiled sheeting, such a...view more

The scope of EN 1090-1:2009+A1:2011 states that the standard covers structural components and kits which are referred to as structural construction products in this document. This Technical Report gives information that clarifies when a structural construction product is covered by the scope of EN 1090-1:2009+A1:2011 and lists examples of products covered and not covered.

EN 1999 applies to the design of buildings and civil engineering and structural works in aluminium. It complies with the principles and requirements for the safety and serviceability of structures, the basis of their design and verification that are given in EN 1990 - Basis of structural design. EN 1999 is only concerned with requirements for resistance, serviceability, durability and fire resistance of aluminium structures. Other requirements, e.g. concerning thermal or sound insulation, are no...view more

(1)   EN 1999-1-1 gives basic design rules for structures made of wrought aluminium alloys and limited guidance for cast alloys (see section 3).
NOTE   Minimum material thickness may be defined in the National Annex. The following limits are recommended – if not otherwise explicitly stated in this standard:
-   components with material thickness not less than 0,6 mm;
-   welded components with material thickness not less than 1,5 mm;
-   connections with:
o   steel bolts and pins with diameter not le...view more

This European Standard specifies requirements for conformity assessment of performance characteristics for structural steel and aluminium components as well as for kits placed on the market as construction products. The conformity assessment covers the manufacturing characteristics, and where appropriate the structural design characteristics. This European Standard covers also the conformity assessment of steel components used in composite steel and concrete structures.
The components can be us...view more

(1) EN 1999-1-3 gives the basis for the design of aluminium alloy structures with respect to the limit state of fracture induced by fatigue.
(2) EN 1999-1-3 gives rules for:
-   Safe life design;
-   damage tolerant design;
-   design assisted by testing.
(3) EN 1999-1-3 is intended to be used in conjunction with EN 1090-3 "Technical requirements for the execution of aluminium structures" which contains the requirements necessary for the design assumptions to be met during execution of compone...view more

EN 1999 applies to the design of buildings and civil engineering and structural works in aluminium. It complies with the principles and requirements for the safety and serviceability of structures, the basis of their design and verification that are given in EN 1990 - Basis of structural design. EN 1999 is only concerned with requirements for resistance, serviceability, durability and fire resistance of aluminium structures. Other requirements, e.g. concerning thermal or sound insulation, are no...view more

EN 1999 applies to the design of buildings and civil engineering and structural works in aluminium. It complies with the principles and requirements for the safety and serviceability of structures, the basis of their design and verification that are given in EN 1990 - Basis of structural design. EN 1999 is only concerned with requirements for resistance, serviceability, durability and fire resistance of aluminium structures. Other requirements, e.g. concerning thermal or sound insulation, are no...view more

This European Standard specifies requirements for conformity assessment of performance characteristics for structural steel and aluminium components as well as for kits placed on the market as construction products. The conformity assessment covers the manufacturing characteristics, and where appropriate the structural design characteristics.
This European Standard covers also the conformity assessment of steel components used in composite steel and concrete structures.
The components can be u...view more

(1) EN 1999-1-3 gives the basis for the design of aluminium alloy structures with respect to the limit state of fracture induced by fatigue.
(2) EN 1999-1-3 gives rules for:
-   Safe life design;
-   damage tolerant design;
-   design assisted by testing.
(3) EN 1999-1-3 is intended to be used in conjunction with EN 1090-3 "Technical requirements for the execution of aluminium structures" which contains the requirements necessary for the design assumptions to be met during execution of compone...view more

(1)P   EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. The execution of aluminium structures made of cold-formed sheeting is covered in EN 1090-3.
NOTE   The rules in this part complement the rules in other parts of EN 1999-1.
(2)   Methods are also given for stressed-skin desig...view more

EN 1999 applies to the design of buildings and civil engineering and structural works in aluminium. It complies with the principles and requirements for the safety and serviceability of structures, the basis of their design and verification that are given in EN 1990 - Basis of structural design. EN 1999 is only concerned with requirements for resistance, serviceability, durability and fire resistance of aluminium structures. Other requirements, e.g. concerning thermal or sound insulation, are no...view more

TC - Modifications to Subclauses A.1.3.1, A.1.3.2 and A.1.4.2 in the E mother reference version.