91.010.30 - Technical aspects

1.1   Scope of CEN/TS 17440
(1)This document provides additional or amended provisions to EN 1990 to cover the assessment of existing structures (see EN 1990:2002, 1.1(4)), and the retained parts of existing structures that are being modified, extended, strengthened or retrofitted.
NOTE 1   The assessment of an existing structure is, in many aspects, different from the design of a new structure, see Introduction.
NOTE 2   There can be some aspects of EN 1990 that are required for design but are not...view more

This document establishes the values of basic module, multimodules for horizontal coordinating dimensions and sub-modular increments for use in modular coordination of buildings. This document also specifies preferred vertical modular dimensions, series of preferred multimodular sizes for horizontal dimensions for all types in accordance with general principles and rules for modular coordination.

EN 1993-1-5 gives design requirements of stiffened and unstiffened plates which are subject to inplane forces. Effects due to shear lag, in-plane load introduction and plate buckling for I-section girders and box girders are covered. Also covered are plated structural components subject to in-plane loads as in tanks and silos. The effects of out-of-plane loading are outside the scope of this document.

EN 1993-1-5 gives design requirements of stiffened and unstiffened plates which are subject to inplane forces. Effects due to shear lag, in-plane load introduction and plate buckling for I-section girders and box girders are covered. Also covered are plated structural components subject to in-plane loads as in tanks and silos. The effects of out-of-plane loading are outside the scope of this document.

DOP of 12 months!

DOP of 12 months!

1.1   General
(1)   This EN provides a design method for fastenings (connection of structural elements and non-structural elements to structural components), which are used to transmit actions to the concrete.
Inserts embedded in precast concrete elements during production, under Factory Production Control (FPC) conditions and with the due reinforcement, intended for use only during transient situations for lifting and handling, are covered by the CEN/TR “Design and Use of Inserts for Lifting and ...view more

1.1   General
(1) This European Standard provides a design method for fastenings (connection of structural elements and non-structural elements to structural components), which are used to transmit actions to the concrete. This design method uses physical models which are based on a combination of tests and numerical analysis consistent with EN 1990:2002, 5.2.
The requirements for the transmission of the fastener loads within the concrete member to its supports are given in EN 1992-1-1 and Annex...view more

This Technical Report reviews current practice with regard to designing, constructing and maintaining the parts of bridges and tracks where railway rails are installed across discontinuities in supporting structures. Current Standards and Codes of Practice are examined and some particular case histories are reviewed. The Technical Report gives guidance with respect to current best practice and makes recommendations for future standards development and also identifies areas in which further resea...view more

This Technical Report reviews current practice with regard to designing, constructing and maintaining the parts of bridges and tracks where railway rails are installed across discontinuities in supporting structures. Current Standards and Codes of Practice are examined and some particular case histories are reviewed. The Technical Report gives guidance with respect to current best practice and makes recommendations for future standards development and also identifies areas in which further resea...view more

This European Standard specifies requirements for the execution, i.e. the manufacture and the installation, of cold-formed structural steel members and sheeting and cold-formed structures for roof, ceiling, floor, wall and cladding applications.
This European Standard applies to structures designed according to the EN 1993 series.
This European Standard applies to structural members and sheeting to be designed according to EN 1993 1 3.
This European Standard may be used for structures designe...view more

DOP of 12 months!

DOP of 12 months!

DOP of 12 months!

DOP of 12 months! * 2017-03-22 FJD - No xml version as mother version was not originally published as xml.

DOP of 12 months!
2017-03-29 FJD - No xml version as the mother standard EN 1993-4-2:2007 was not edited as an xml deliverable.

DOP of 12 months!

DOP of 12 months!

DOP of 12 months!