21.060.01 - Fasteners in general

This document specifies general rules and provides technical information on stainless steels and their properties, which are relevant when using other parts of the ISO 3506 series. It includes specifications for corrosion-resistant stainless steels and nickel alloys, which are suitable for the manufacture of fasteners. It applies to austenitic, martensitic, ferritic and duplex (austenitic-ferritic) stainless steel grades and nickel alloys for fasteners, and is intended to be used together with t...view more

This document specifies an inspection procedure to be used by the purchaser where no prior agreement exists. It also specifies a reference acceptance procedure for acceptance or rejection of an inspection lot, when no agreement can be reached between the purchaser and the supplier, or where conformance to specification is disputed. It applies to inspection lots of bolts, screws, studs, nuts, pins, washers, rivets and other related fasteners. This document applies to fasteners not intended for hi...view more

This document specifies an inspection procedure to be used by the purchaser where no prior agreement exists.
It also specifies a reference acceptance procedure for acceptance or rejection of an inspection lot, when no agreement can be reached between the purchaser and the supplier, or where conformance to specification is disputed.
It applies to inspection lots of bolts, screws, studs, nuts, pins, washers, rivets and other related fasteners.
This document applies to fasteners not intended for...view more

This document specifies an inspection procedure to be used by the purchaser where no prior agreement exists. It also specifies a reference acceptance procedure for acceptance or rejection of an inspection lot, when no agreement can be reached between the purchaser and the supplier, or where conformance to specification is disputed. It applies to inspection lots of bolts, screws, studs, nuts, pins, washers, rivets and other related fasteners. This document applies to fasteners not intended for hi...view more

This document specifies the characteristics of hexagon washer head drilling screws with tapping screw threads, made of steel, with thread sizes ST2,9 to ST6,3, and with product grade A.

This document presents the latest knowledge related to hydrogen embrittlement, translated into know-how in a manner that is complete yet simple, and directly applicable to steel fasteners.

This Technical Report gives provisions for design of ultimate limit states in addition to EN 1992 4 for headed and post-installed fasteners excluding concrete screws, which only transmit static actions to the concrete, when the loads on individual fasteners are determined according to plastic analysis of the joint where only equilibrium conditions but no compatibility conditions are considered. Fatigue, impact and seismic loads are not covered.

1.1   General
This Technical Report provides design rules for fasteners used to connect statically indeterminate non-structural light weight systems (e.g. suspended ceilings, pipe work, ducting) to concrete members such as walls or floors (see Figure 1)).
The proposed design model may be applied to post-installed mechanical and bonded anchors covered by EN 1992-4:2017, 1.2. Their suitability will be confirmed in a European Technical Product Specification.
The design rules assume the following:
...view more

EN 1992-4 covers anchor channels located in cracked or uncracked concrete subjected to tensile loads and/or shear loads transverse to the longitudinal channel axis as well as combinations of these loads. Shear loads acting in direction of the longitudinal axis of the channel and combinations of shear loads acting transverse and in direction of the longitudinal axis of the channel, combinations of tensile loads and shear loads acting in direction of the longitudinal axis of the channel and combin...view more

1.1   General
(1)   This EN provides a design method for fastenings (connection of structural elements and non-structural elements to structural components), which are used to transmit actions to the concrete.
Inserts embedded in precast concrete elements during production, under Factory Production Control (FPC) conditions and with the due reinforcement, intended for use only during transient situations for lifting and handling, are covered by the CEN/TR “Design and Use of Inserts for Lifting and ...view more

This document specifies requirements for non-electrolytically applied zinc flake coating systems for
steel fasteners. It is applicable to coatings:
— with or without hexavalent chromium;
— with or without top coat;
— with or without lubricant (integral lubricant and/or subsequently added lubricant).
It is applicable to bolts, screws, studs and nuts with ISO metric thread, to fasteners with non-ISO metric
thread, and to non-threaded fasteners such as washers, pins, clips, etc.
This documen...view more

This document specifies requirements for electroplated coatings and coating systems on steel
fasteners. The requirements related to dimensional properties also apply to fasteners made of copper
or copper alloys.
It also specifies requirements and gives recommendations to minimize the risk of hydrogen
embrittlement; see 4.4 and Annex B.
It mainly applies to zinc and zinc alloy coating systems (zinc, zinc-nickel, zinc-iron) and cadmium,
primarily intended for corrosion protection and other f...view more

1.1   General
This Technical Report provides design rules for fasteners used to connect statically indeterminate non-structural light weight systems (e.g. suspended ceilings, pipe work, ducting) to concrete members such as walls or floors (see Figure 1)).
The proposed design model may be applied to post-installed mechanical and bonded anchors covered by EN 1992-4:2017, 1.2. Their suitability will be confirmed in a European Technical Product Specification.
The design rules assume the following:
...view more

This Technical Report gives provisions for design of ultimate limit states in addition to EN 1992 4 for headed and post-installed fasteners excluding concrete screws, which only transmit static actions to the concrete, when the loads on individual fasteners are determined according to plastic analysis of the joint where only equilibrium conditions but no compatibility conditions are considered. Fatigue, impact and seismic loads are not covered.

EN 1992-4:2018 covers anchor channels located in cracked or uncracked concrete subjected to tensile loads and/or shear loads transverse to the longitudinal channel axis as well as combinations of these loads. Shear loads acting in direction of the longitudinal axis of the channel and combinations of shear loads acting transverse and in direction of the longitudinal axis of the channel, combinations of tensile loads and shear loads acting in direction of the longitudinal axis of the channel and c...view more

This document specifies requirements for electroplated coatings and coating systems on steel fasteners. The requirements related to dimensional properties also apply to fasteners made of copper or copper alloys.
It also specifies requirements and gives recommendations to minimize the risk of hydrogen embrittlement; see 4.4 and Annex B.
It mainly applies to zinc and zinc alloy coating systems (zinc, zinc-nickel, zinc-iron) and cadmium, primarily intended for corrosion protection and other funct...view more

This document specifies requirements for non-electrolytically applied zinc flake coating systems for steel fasteners. It is applicable to coatings:
— with or without hexavalent chromium;
— with or without top coat;
— with or without lubricant (integral lubricant and/or subsequently added lubricant).
It is applicable to bolts, screws, studs and nuts with ISO metric thread, to fasteners with non-ISO metric thread, and to non-threaded fasteners such as washers, pins, clips, etc.
This document ...view more

This part of ISO 1891 specifies terms and definitions for fastener related to control, inspection, delivery, acceptance and quality.
These terms are mainly intended for use in conjunction with ISO 3269, ISO 16228 and ISO 16426.
A multilingual list of terms in alphabetical order is given in Annex A.

This document specifies requirements for non-electrolytically applied zinc flake coating systems for steel fasteners. It is applicable to coatings: — with or without hexavalent chromium; — with or without top coat; — with or without lubricant (integral lubricant and/or subsequently added lubricant). It is applicable to bolts, screws, studs and nuts with ISO metric thread, to fasteners with non-ISO metric thread, and to non-threaded fasteners such as washers, pins, clips, etc. This document does ...view more