iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13317:2018

(Main)

Tanks for transport of dangerous goods - Service equipment for tanks - Manhole cover assembly

Tanks for transport of dangerous goods - Service equipment for tanks - Manhole cover assembly

This document covers the manhole cover assembly and specifies the performance requirements, dimensions and tests necessary to verify the compliance of the equipment to this standard.
The equipment specified by this standard is suitable for use with liquid petroleum products and other dangerous substances of Class 3 of ADR - European Agreement concerning the International Carriage of Dangerous Goods by Road which have a vapour pressure not exceeding 110 kPa at 50 °C and petrol, and which have no sub-classification as toxic or corrosive.

Tanks für die Beförderung gefährlicher Güter - Bedienungsausrüstung von Tanks - Baugruppe Deckel für Einsteigeöffnungen

Diese Europäische Norm gilt für die Baugruppe Deckel für Einsteigeöffnungen und legt die Leistungs-anforderungen, Maße und Prüfungen fest, mit denen nachgewiesen werden kann, ob die Ausrüstung den Anforderungen dieser Norm entspricht.
Die in dieser Norm beschriebene Ausrüstung ist für flüssige Erdölerzeugnisse und andere gefährliche Güter der Klasse 3 (entzündbare Flüssigkeiten) des Europäischen Übereinkommens über die internationale Beför¬derung gefährlicher Güter auf der Straße (ADR) geeignet, deren Dampfdruck bei 50 °C höchstens 110 kPa beträgt (einschließlich Ottokraftstoff) und die nicht als giftig oder ätzend eingestuft sind.

Citernes pour le transport de matières dangereuses - Équipements de service pour citernes - Couvercle de trou d'homme

La présente Norme européenne s'applique aux couvercles de trou d’homme et spécifie les exigences de performance, les dimensions et les essais nécessaires pour vérifier la conformité du dispositif à la présente norme.
L’équipement spécifié par la présente norme convient à une utilisation avec des produits pétroliers liquides et autres matières dangereuses de la classe 3 de l’ADR - Accord européen relatif au transport international des marchandises dangereuses par route - (liquides inflammables) dont la tension de vapeur ne dépasse pas 110 kPa à 50 °C (y compris l’essence) et qui n’appartiennent à aucune sous-classification des produits toxiques ou corrosifs.

Cisterne za prevoz nevarnega blaga - Oprema za obratovanje cistern - Sklop pokrova vstopne odprtine

Ta evropski standard zajema sklop pokrova vstopne odprtine ter določa zahteve glede zmogljivosti, dimenzije in preskuse, potrebne za preverjanje skladnosti opreme s tem evropskim standardom.
Oprema, ki jo določa ta standard, je primerna za uporabo s tekočimi naftnimi proizvodi in drugimi nevarnimi snovmi kategorije 3 ADR – Evropski sporazum o prevozu nevarnega blaga po cesti – (vnetljive tekočine), katerih parni tlak ne presega 110 kPa pri 50 °C, vključno z bencinom, pri čemer niso dodatno opredeljeni kot strupeni ali korozivni.

General Information

Status
Published
Publication Date
10-Jul-2018
Withdrawal Date
30-Jan-2019
ICS
13.300 - Protection against dangerous goods
23.020.10 - Stationary containers and tanks
23.020.20 - Vessels and containers mounted on vehicles
Technical Committee
CEN/TC 296 - Tanks for transport of dangerous goods
Drafting Committee
CEN/TC 296/WG 7 - Service equipment (including equipment for vapour recovery, bottom loading, the confinement and handling of petroleum products)
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
03-Mar-2024
Completion Date
03-Mar-2024
Directive
2008/68/EC - Directve 2008/68/EC of the European Parliament and of the council of 24 September 2008 on the inland transport of the dangerous goods
Mandate
M/086 - Mandate to CEN for standardization in the field of transport of dangerous goods
Ref Project
SIST EN 13317:2018 - Tanks for transport of dangerous goods - Service equipment for tanks - Manhole cover assembly

Relations

Replaces
EN 13317:2002+A1:2006 - Tanks for transport of dangerous goods - Service equipment for tanks - Manhole cover assembly
Effective Date
08-Jun-2022

Buy Standard

EN 13317:2018EN 13317:2018
PreviousNext
Standard
EN 13317:2018
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cisterne za prevoz nevarnega blaga - Oprema za obratovanje cistern - Sklop pokrova vstopne odprtineTanks für die Beförderung gefährlicher Güter - Bedienungsausrüstung von Tanks - Baugruppe Deckel für EinsteigeöffnungenCiternes pour le transport de matières dangereuses - Équipements de service pour citernes - Couvercle de trou d'hommeTanks for transport of dangerous goods - Service equipment for tanks - Manhole cover assembly23.020.20Posode in vsebniki, montirani na vozilaVessels and containers mounted on vehicles13.300Varstvo pred nevarnimi izdelkiProtection against dangerous goodsICS:Ta slovenski standard je istoveten z:EN 13317:2018SIST EN 13317:2018en,fr,de01-november-2018SIST EN 13317:2018SLOVENSKI
STANDARDSIST EN 13317:2003+A1:20071DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13317
July
t r s z ICS
s uä u r râ
t uä r t rä t r Supersedes EN
s u u s yã t r r t ªA sã t r r xEnglish Version
Tanks for transport of dangerous goods æ Service equipment for tanks æ Manhole cover assembly Citernes destinées au transport de matières dangereuses æ Équipements de service pour citernes æ Couvercle de trou d 5homme
Tanks für die Beförderung gefährlicher Güter æ Bedienungsausrüstung von Tanks æ Baugruppe Deckel für Einsteigeöffnungen This European Standard was approved by CEN on
t u April
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u u s yã t r s z ESIST EN 13317:2018

Drop test apparatus . 11 Annex B (normative)
Dimensions of mounting bolt holes . 12 Annex C (normative)
Dimensions for bolted assembly . 13 Bibliography . 14
IEC Electropedia: available at http://www.electropedia.org/
ISO Online browsing platform: available at http://www.iso.org/obp 3.1 manhole opening in a tank to allow internal inspection by a person passing through 3.2 manhole cover cover of the manhole which forms an integral part of a loading, unloading or venting function Note 1 to entry: Loading, unloading or venting function may include auxiliary equipment such as vapour transfer valve, emergency pressure relief valve and sensors. 3.3 manhole cover neckring shell ring permanently joined to the tank that provides the attachment point for the manhole cover SIST EN 13317:2018
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 16657:2016+A1:2018(Main)
Tanks for the transport of dangerous goods - Transport tank equipment for overfill prevention devices for static tanks
SIST EN 16657:2016+A1:2018

This European Standard specifies the minimum performance and construction requirements for overfill prevention controllers located on the tank vehicle.
This European Standard applies to overfill prevention controllers for liquid fuels, having a flash point up to but not exceeding 100 °C.
The requirements apply to overfill prevention controllers suitable for use at ambient temperatures in the range from  25 °C to +60 °C, and subject to normal operational pressure variations.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13314:2002(Main)
Tanks for transport of dangerous goods - Service equipment for tanks - Fill hole cover
SIST EN 13314:2003

This European standard is applicable to fill hole covers and specifies the performance requirements, critical dimensions and tests necessary to verify the compliance of the equipment to this standard. The equipment specified in this standard is suitable for use with liquid petroleum products and other dangerous substances of class 3 (flammable liquids) of ADR - European Agreement concerning the International Carriage of Dangerous Goods By Road - which have a vapour pressure at 50°C not greater than 110kPa.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16657:2016/prA1(Amendment)
Tanks for the transport of dangerous goods - Transport tank equipment for overfill prevention devices for static tanks
SIST EN 16657:2016/oprA1:2017

This European Standard specifies the minimum performance and construction requirements for overfill prevention controllers located on the tank vehicle.
This European Standard applies to overfill prevention controllers for liquid fuels, having a flash point up to but not exceeding 100 °C.
The requirements apply to overfill prevention controllers suitable for use at ambient temperatures in the range from  25 °C to +60 °C, and subject to normal operational pressure variations.

  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16657:2016+A1:2018(Main)
Tanks for the transport of dangerous goods - Transport tank equipment for overfill prevention devices for static tanks
SIST EN 16657:2016+A1:2018

This European Standard specifies the minimum performance and construction requirements for overfill prevention controllers located on the tank vehicle.
This European Standard applies to overfill prevention controllers for liquid fuels, having a flash point up to but not exceeding 100 °C.
The requirements apply to overfill prevention controllers suitable for use at ambient temperatures in the range from  25 °C to +60 °C, and subject to normal operational pressure variations.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13314:2002(Main)
Tanks for transport of dangerous goods - Service equipment for tanks - Fill hole cover
SIST EN 13314:2003

This European standard is applicable to fill hole covers and specifies the performance requirements, critical dimensions and tests necessary to verify the compliance of the equipment to this standard. The equipment specified in this standard is suitable for use with liquid petroleum products and other dangerous substances of class 3 (flammable liquids) of ADR - European Agreement concerning the International Carriage of Dangerous Goods By Road - which have a vapour pressure at 50°C not greater than 110kPa.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16657:2016/prA1(Amendment)
Tanks for the transport of dangerous goods - Transport tank equipment for overfill prevention devices for static tanks
SIST EN 16657:2016/oprA1:2017

This European Standard specifies the minimum performance and construction requirements for overfill prevention controllers located on the tank vehicle.
This European Standard applies to overfill prevention controllers for liquid fuels, having a flash point up to but not exceeding 100 °C.
The requirements apply to overfill prevention controllers suitable for use at ambient temperatures in the range from  25 °C to +60 °C, and subject to normal operational pressure variations.

  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-9:2024(Main)
Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table) (ISO 19085-9:2024)
SIST EN ISO 19085-9:2024

This document specifies the safety requirements and measures for circular saw benches with or without sliding table or demountable power feed unit or both and capable of continuous production use, also known as “table saws” (in the USA), hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices or working units, whose hazards have been dealt with:
—     device for the main saw blade and scoring saw blade to be raised and lowered through the table;
—     device to tilt the main saw blade and scoring saw blade for angled cutting;
—     device for scoring;
—     device for grooving with milling tool with a width not exceeding 20 mm in one pass;
—     demountable power feed unit;
—     additional manually operated sliding table;
—     powered workpiece clamping device.
This document does not apply to:
a)       machines intended for outdoor use on building sites;
NOTE            Building site saws (contractor saws) are covered by the requirements of ISO 19085-10:2018.
b)       handheld woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting;
c)        machines intended for use in a potentially explosive atmosphere;
d)       machines manufactured prior to the publication of this document.

  • Draft
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17928-2:2024(Main)
Gas infrastructure - Injection stations - Part 2: Specific requirements regarding the injection of biomethane
kSIST FprEN 17928-2:2024

This document establishes specific functional requirements for injection stations for biomethane into gas transmission and distribution systems operated with gases of the second gas family in accordance with EN 437 in addition to the general functional requirements of EN 17928 1:2024.
This document represents the recommendations at the time of its preparation. This document does not apply to injection stations operating prior to the publication of this document.
This document complements EN 17928 1:2024 by specifying the technical safety requirements to be observed in respect of the chemical and physical properties of biomethane.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
—   legislation/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16186-6:2024(Main)
Railway applications - Driver's cab - Part 6: Integration of displays, controls and indicators for tram vehicles
SIST EN 16186-6:2024

This document is applicable to vehicles operating on tram networks.
This document gives design requirements and guidance in order to ensure visibility and operability of displays, controls and indicators in the cab in all operating conditions (day, night, natural or artificial lighting).
It covers four aspects:
-   the characteristics of the displays, controls and indicators in order to ensure proper visibility: i.e. range of luminance and contrast as well as the possibility of adjustment of perceived brightness;
-   the requirements for the location of the displays, keyboards, controls and indicators in the cab and on the driver’s desk: i.e. position, angle of visibility, etc. with consideration of the normal driving position and the working environment (windscreen, natural or artificial lighting in the cab, unwanted glare and reflections, etc.);
-   the characteristics and requirements for the location of microphones and loudspeakers;
-   design of symbols.
NOTE   All element numbers within the text refer to Table B.1.
This document does not apply to refurbishment of existing vehicles. This document is not intended to be applicable to driver's auxiliary desk, except for 5.3.13, Clause 6, 7.1.2, Clause 9 and Table B.1.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-8:2024(Main)
Woodworking machines - Safety - Part 8: Wide belt sanding machines and surface treating machines (ISO 19085-8:2024)
SIST EN ISO 19085-8:2024

This document specifies the safety requirements and measures for wide belt sanding machines (defined in 3.1) and for surface treating machines (defined in 3.2) capable of continuous production use, altogether referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events, as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases are also taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—     transversal sanding unit;
—     cleaning brushing unit;
—     satining roller unit;
—     disk brushing unit;
—     texturing brushing roller unit;
—     texturing brushing belt unit;
—     cutterblock unit;
—     texturing band saw unit;
—     spiked roller unit;
—     multi blade unit;
—     conveyor directly controlled by the machine;
—     additional workpiece vacuum clamping device;
—     antistatic bar unit.
NOTE 1        An antistatic bar is a device that eliminates electrostatic charges on the workpiece to ease its subsequent cleaning from dust by airflow.
This document is also applicable to machines fitted with a laser engraving unit, but the specific hazards of this unit have not been dealt with.
The machines are designed to process workpieces with flat surface and even thickness, in shape of panels or beams or frames, consisting of:
a)       solid wood;
b)       material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2);
c)        gypsum boards, gypsum bounded fibreboards;
d)       composite materials with core consisting of, e.g. polyurethane or mineral material;
e)       composite boards made from the materials listed above;
f)         all materials listed above, already lacquered.
This document does not deal with hazards related to:
—     specific devices other than those listed above;
—     access through in-feed and out-feed openings of machines with a work piece height capacity greater than 700 mm;
—     systems for powered loading or unloading, or both, of the workpiece to or from a single machine;
NOTE 2        Loading the machine manually includes manually placing the workpiece onto a conveyor directly controlled by the machine. Unloading the machine manually includes manually removing the workpiece from a conveyor directly controlled by the machine.
—     out-feed workpieces on machines with feed speed higher than 60 m/min;
—     interfacing of the machine with any other machine.
This document is not applicable to machines intended for use in a potentially explosive atmosphere and to machines manufactured prior to the date of its publication.

  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day