iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12067-1:1998

(Main)

Gas/air ratio controls for gas burners and gas burning appliances - Part 1: Pneumatic types

Gas/air ratio controls for gas burners and gas burning appliances - Part 1: Pneumatic types

This Part of this European Standard, EN 12067 specifies the safety, construction and performance requirements for gas/air ratio controls for inlet pressures up to and including 500 mbar of nominal connection size up to and including DN 150 , intended for use with gas appliances for use with one or more fuel gases of the first, second or third families. It also describes the test procedures for evaluating these requirements and specifies information necessary for installation and use.  It applies to gas/air ratio controls for gas burning appliances that can be tested independently of the appliance.  It applies to gas/air ratio controls which function by controlling a gas pressure (or differential pressure) output in response to an air pressure (or differential pressure) signal input, but gas/air ratio controls which change the air pressure in response to the gas pressure are not excluded.  It does not cover mechanically linked valves and electronic systems.  NOTE: Parts of the standard can be applied to the construction and performance of the ratio control function of multi-functional controls.

Gas-Luft-Verbundregler für Gasbrenner und Gasgeräte - Teil 1: Pneumatische Ausführung

Dieser Teil der Europäischen Norm EN 12067 legt Anforderungen an die Sicherheit, sowie Bau- und Funktionsanforderungen an Gas-Luft-Verbundregler für einen Eingangsdruck bis einschließlich 500 mbar und einer Nennweite bis einschließlich DN 150 fest, die zu einem Einsatz an Gasgeräten für eine oder mehrere der Brenngase der ersten, zweiten oder dritten Gasfamilie vorgesehen sind. Sie beschreibt auch die Prüfverfahren, nach denen die Einhaltung dieser Anforderungen beurteilt werden, und nennt die für den Käufer und Anwender erforderlichen Informationen.

Dispositifs de régulation du rapport air/gaz pour brûleurs à gaz et appareils à gaz - Partie 1: Dispositifs pneumatiques

La présente partie de la norme européenne EN 12067 précise les spécifications de sécurité, de construction et de fonctionnement des dispositifs de régulation du rapport air/gaz, alimentés sous une pression d'entrée inférieure ou égale à 500 mbar et avec une dimension nominale de raccordement jusqu'à DN 150 comprise, et destinés à équiper des appareils utilisant un ou plusieurs gaz combustibles des première, deuxième et troisième familles. Elle donne aussi les procédures d'essais permettant de vérifier la conformité à ces exigences ainsi que les informations nécessaires à l'installation ...

Regulatorji razmerja plina in zraka za plinske gorilnike in plinske aparate - 1. del: Pnevmatski tip

General Information

Status
Withdrawn
Publication Date
20-Oct-1998
Withdrawal Date
05-Apr-2011
ICS
23.060.40 - Pressure regulators
27.060.20 - Gas fuel burners
Technical Committee
CEN/TC 58 - Safety and control devices for burners and appliances burning gaseous or liquid fuels
Drafting Committee
CEN/TC 58 - Safety and control devices for burners and appliances burning gaseous or liquid fuels
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
06-Apr-2011
Completion Date
06-Apr-2011
Directive
2009/142/EC - DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 30 November 2009 relating to appliances burning gaseous fuels
90/396/EEC - Appliances burning gaseous fuels
Mandate
M/BC/CEN/89/6 - Standardization request to CEN concerning appliances burning gaseous fuels
Ref Project
SIST EN 12067-1:1999 - Gas/air ratio controls for gas burners and gas burning appliances - Part 1: Pneumatic types

Relations

Replaced By
EN 88-1:2011 - Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa
Effective Date
09-Apr-2011
Amended By
EN 12067-1:1998/A1:2003 - Gas/air ratio controls for gas burners and gas burning appliances - Part 1: Pneumatic types
Effective Date
08-Jun-2022

Buy Standard

EN 12067-1:1999EN 12067-1:1999
PreviousNext
Standard
EN 12067-1:1999
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-1999
Regulatorji razmerja plina in zraka za plinske gorilnike in plinske aparate - 1. del:
Pnevmatski tip
Gas/air ratio controls for gas burners and gas burning appliances - Part 1: Pneumatic
types
Gas-Luft-Verbundregler für Gasbrenner und Gasgeräte - Teil 1: Pneumatische
Ausführung
Dispositifs de régulation
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12067-2:2022(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Part 2: Fuel/air ratio control/supervision of the electronic type
SIST EN 12067-2:2023

EN 13611:2019, Clause 1 is replaced by the following:
This document specifies the safety, design, construction and performance requirements, and testing for electronic fuel/air ratio control systems (ERC), electronic fuel/air ratio supervision systems (ERS) and electronic fuel/air ratio trim systems (ERT) intended for use with burners and appliances burning gaseous or liquid fuels. It also describes the procedures for evaluating these requirements and specifies information necessary for installation and use.
This document is applicable to:
-   closed loop fuel/air ratio control systems, see 3.101;
-   fuel/air ratio supervision systems, see 3.102;
-   closed loop fuel/air ratio trim systems, see 3.103;
and does not differentiate into classification by heat input.
NOTE   The documents for burners, appliances or processes which use ERC, ERS or ERT can override the requirements of this document.

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12067-2 rev(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Part 2: Fuel/air ratio control / supervision of the electronic type
oSIST prEN 12067-2:2016

This European Standard specifies the safety, construction and performance requirements for electronic fuel/air ratio control (ERC), electronic fuel/air ratio supervision (ERS) and electronic fuel/air ratio trim (ERT) intended for use with burners and appliances burning gaseous or liquid fuels. It also describes the test procedures for evaluating these requirements and specifies information necessary for installation and use.
This standard is applicable to
-   closed loop fuel/air ratio controls (see 3.101),
-   fuel/air ratio supervision systems (see 3.102),
-   closed loop fuel/air ratio trim systems (see 3.103) and does not differentiate into classification by heat input.
This standard applies to ERC, ERS or ERT that can be tested independently, as well as part of an appliance or a burner.
NOTE 1 European Standards for burners, appliances or processes which use ERC, ERS or ERT can override the requirements of this standard.
NOTE 2 Provisions for production control are not part of this European Standard.

  • Draft
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12067-2:2022(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Part 2: Fuel/air ratio control/supervision of the electronic type
SIST EN 12067-2:2023

EN 13611:2019, Clause 1 is replaced by the following:
This document specifies the safety, design, construction and performance requirements, and testing for electronic fuel/air ratio control systems (ERC), electronic fuel/air ratio supervision systems (ERS) and electronic fuel/air ratio trim systems (ERT) intended for use with burners and appliances burning gaseous or liquid fuels. It also describes the procedures for evaluating these requirements and specifies information necessary for installation and use.
This document is applicable to:
-   closed loop fuel/air ratio control systems, see 3.101;
-   fuel/air ratio supervision systems, see 3.102;
-   closed loop fuel/air ratio trim systems, see 3.103;
and does not differentiate into classification by heat input.
NOTE   The documents for burners, appliances or processes which use ERC, ERS or ERT can override the requirements of this document.

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12186:2014(Main)
Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements
SIST EN 12186:2015

This European Standard contains the relevant functional requirements for gas pressure regulating stations, which form part of gas transmission or distribution systems. It is applicable to the design, materials, construction, testing, operation and maintenance of gas pressure regulating stations.
This European Standard does not apply to gas pressure regulating stations commissioned prior to the publication of this standard.
The stations covered by this European Standard have a maximum upstream operating pressure which does not exceed 100 bar. For higher maximum upstream operating pressures this standard should be used as a guideline.
If the inlet pipework of the station is a service line and the maximum upstream operating pressure does not exceed 16 bar and the design flow rate is equal to or less than 200 m3/h under normal conditions, EN 12279 applies.
Basic system requirements for gas pressure regulating stations are contained in this European Standard. Requirements for individual components (valves, regulators, safety devices, pipes, etc.) or installation of the components are contained in the appropriate European Standards.
NOTE   For combined regulating and measuring stations, the additional requirements of EN 1776 can apply.
The requirements in this European Standard do not apply to the design and construction of auxiliary facilities such as sampling, calorimetering, odorization systems and density measuring. These facilities are covered by the appropriate European Standards, where existing, or other relevant standards.
The requirements of this European Standard are based on good gas engineering practice under conditions normally encountered in the gas industry. Requirements for unusual conditions cannot be specifically provided for, nor are all engineering and construction details prescribed.
The requirements in this European Standard are based on the physical and chemical data of gaseous fuels – including non-conventional gases – in accordance with Table 1 of EN 437:2003+A1:2009 for first and second family gases. Additional requirements in the case of gaseous fuels heavier than air and/or sour gases are not covered by this European Standard.
The objective of this European Standard is to ensure the safe operation of such stations. This does not, however, relieve all concerned of the responsibility for taking the necessary care and applying effective quality management during the design, construction and operation.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12067-2 rev(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Part 2: Fuel/air ratio control / supervision of the electronic type
oSIST prEN 12067-2:2016

This European Standard specifies the safety, construction and performance requirements for electronic fuel/air ratio control (ERC), electronic fuel/air ratio supervision (ERS) and electronic fuel/air ratio trim (ERT) intended for use with burners and appliances burning gaseous or liquid fuels. It also describes the test procedures for evaluating these requirements and specifies information necessary for installation and use.
This standard is applicable to
-   closed loop fuel/air ratio controls (see 3.101),
-   fuel/air ratio supervision systems (see 3.102),
-   closed loop fuel/air ratio trim systems (see 3.103) and does not differentiate into classification by heat input.
This standard applies to ERC, ERS or ERT that can be tested independently, as well as part of an appliance or a burner.
NOTE 1 European Standards for burners, appliances or processes which use ERC, ERS or ERT can override the requirements of this standard.
NOTE 2 Provisions for production control are not part of this European Standard.

  • Draft
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 16931-8:2024(Main)
Electronic invoicing - Part 8: Semantic data model of the elements of an e-receipt or a simplified electronic invoice
kSIST FprEN 16931-8:2024

This document establishes a semantic data model of an e-receipt or a simplified electronic invoice.
NOTE   In the remainder of this document, when “e-receipt” is mentioned, “simplified invoice” is also meant.
The semantic model includes essential information elements that an electronic receipt needs to ensure legal (including fiscal) compliance and to enable interoperability for cross-border, cross sector and domestic trade. The semantic model can be used by organizations in the private and the public sector for documenting by issuing a receipt for the purchase of services and /or goods. It can also be used for documenting a purchase between private sector enterprises. In addition, it has been designed for the use of consumers.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19403-5:2024(Main)
Paints and varnishes - Wettability - Part 5: Determination of the polar and dispersive fractions of the surface tension of liquids from contact angles measurements on a solid with only a disperse contribution to its surface energy (ISO 19403-5:2024)
kSIST FprEN ISO 19403-5:2024

This document specifies a test method to determine the polar and dispersive fractions of the surface tension of liquids by optical methods. The method can be applied for the characterization of liquid coating materials.
If applied to liquids with non-Newtonian flow behaviour (see ISO 3219-1:2021, 3.22), restrictions can apply.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16286-1:2024(Main)
Railway applications - Gangway systems between vehicles - Part 1: Main applications
SIST EN 16286-1:2024

This document specifies the technical and safety requirements applicable to gangway systems used in heavy rail and urban rail vehicles that are designed to allow passengers or staff to move between adjacent vehicles.
It also specifies:
- the requirements for the safety for passengers and/or staff in the gangway while the train is running,
- the assessment methods as well as pass/fail criteria for gangways installed on vehicles.
NOTE Some requirements in this document may not be applicable for gangways designed for use by staff only.
This document is not intended to specify requirements for articulation systems which can be an integral part of gangway systems.
This document is not applicable for rubber tube gangways and interconnecting gangways for coaches travelling at speeds of up to 200 km/h on high-speed lines with tunnel sections. Information about these types of gangway systems are given in Annex A and Annex B.

  • Draft
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17966:2024(Main)
Fire protection equipment - Carbon dioxide extinguishing systems for use on premises - Design and installation (ISO 6183:2022, modified)
SIST EN 17966:2024

This document specifies requirements and gives recommendations for the design, installation, testing, maintenance and safety of fixed carbon dioxide firefighting systems in buildings, plants or other structures. It is not applicable to extinguishing systems on ships, in aircraft, on vehicles or on mobile fire appliances, or to below ground systems in the mining industry; nor does it apply to carbon dioxide pre-inerting systems.
Design of systems where unclosable opening(s) of the protected volume exceed a specified area and where the opening(s) can be subject to the effect of wind is not specified, although general guidance on the procedure to be followed in such cases is given (see 7.4.3.2).

  • Draft
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21009-2:2024(Main)
Cryogenic vessels - Static vacuum-insulated vessels - Part 2: Operational requirements (ISO 21009-2:2024)
SIST EN ISO 21009-2:2024

This document specifies operational requirements for static vacuum insulated vessels designed for a maximum allowable pressure of more than 50 kPa (0,5 bar). It can also be used as a guideline for vessels designed for a maximum allowable pressure of less than 50 kPa (0,5 bar).
This document applies to vessels designed for cryogenic fluids specified in ISO 21009-1.
Static cryogenic vessels are often partly equipped by the manufacturer, but can be installed or re- installed by another party, such as the operator, user or owner.
NOTE 1        For the installation of these vessels, additional requirements can apply.
NOTE 2        Some requirements of this document can be covered by local regulations, e.g. safety distances, occupational safety and health.
NOTE 3        Additional requirements can apply to the operation of large scale and field-fabricated vessels.

  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day