EN 12430:2013
(Main)Thermal insulating products for building applications - Determination of behaviour under point load
Thermal insulating products for building applications - Determination of behaviour under point load
This European Standard specifies equipment and procedures for determining the behaviour of products under a force applied to a small area of a test specimen at a given speed. It is applicable to thermal insulating products.
This European Standard can be used to determine whether the products have sufficient strength to withstand forces applied directly to them either during installation or during application, mainly caused by pedestrian traffic.
NOTE The test methods given in the main body of the standard and in Annex A are reported and interpreted in different ways. The similarities that exist between the methods are not sufficient to permit reasonable comparisons to be made.
Wärmedämmstoffe für das Bauwesen - Bestimmung des Verhaltens unter Punktlast
Diese Europäische Norm legt Prüfeinrichtungen und Verfahren zur Bestimmung des Verhaltens von Produkten unter einer Belastung fest, die auf einen kleinen Bereich eines Probekörpers mit vorgegebener Geschwindigkeit aufgebracht wird. Sie gilt für Wärmedämmstoffe.
Diese Europäische Norm kann angewendet werden, um zu bestimmen, ob die Produkte eine ausreichende Festigkeit haben um Belastungen standzuhalten, die entweder bei der Montage oder bei der Anwendung, im Wesentlichen durch Begehen verursacht werden.
ANMERKUNG Die im Haupttext der Norm und im Anhang A angegebenen Prüfverfahren unterscheiden sich in ihrer Darstellung und Auslegung. Die bestehenden Ähnlichkeiten dieser Verfahren reichen nicht aus, um Vergleiche mit hinreichender Aussagekraft anstellen zu können.
Produits isolants thermiques destinés aux applications du bâtiment - Détermination du comportement sous charge ponctuelle
La présente Norme européenne spécifie l'équipement et les modes opératoires permettant de déterminer le comportement de produits sous une charge appliquée sur une petite surface de l'éprouvette, à une vitesse donnée. Elle s'applique aux produits isolants thermiques.
La présente Norme européenne peut être utilisée pour déterminer si les produits ont une résistance suffisante pour supporter des charges appliquées directement pendant leur installation ou pendant l'utilisation, principalement causées par le trafic pédestre.
NOTE Les méthodes d'essai décrites dans la partie principale de la norme et en Annexe A sont rapportées et interprétées de différentes manières. Les similitudes qui existent entre les différentes méthodes ne sont pas suffisantes pour permettre des comparaisons raisonnables des résultats.
Toplotnoizolacijski proizvodi za uporabo v gradbeništvu - Ugotavljanje obnašanja pri točkovni obremenitvi
Ta evropski standard določa opremo in postopke za določanje obnašanja izdelkov pod silo, uporabljeno na majhnem področju preskusnega vzorca pri dani hitrosti. Uporablja se za toplotnoizolacijske proizvode. Ta evropski standard se lahko uporablja za ugotavljanje, ali so izdelki dovolj trdni, da bodo zdržali sile, uperjene neposredno nanje med namestitvijo ali med uporabo, v glavnem s strani pešcev.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Wärmedämmstoffe für das Bauwesen - Bestimmung des Verhaltens unter PunktlastProduits isolants thermiques destinés aux applications du bâtiment - Détermination du comportement sous charge ponctuelleThermal insulating products for building applications - Determination of behaviour under point load91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 12430:2013SIST EN 12430:2013en,fr,de01-julij-2013SIST EN 12430:2013SLOVENSKI
STANDARDSIST EN 12430:1999/A1:2007SIST EN 12430:19991DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12430
March 2013 ICS 91.100.60 Supersedes EN 12430:1998English Version
Thermal insulating products for building applications - Determination of behaviour under point load
Produits isolants thermiques destinés aux applications du bâtiment - Détermination du comportement sous charge ponctuelle
Wärmedämmstoffe für das Bauwesen - Bestimmung des Verhaltens unter Punktlast This European Standard was approved by CEN on 15 December 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12430:2013: ESIST EN 12430:2013
Modifications to the general test method for cellular glass products . 11
The revision of this standard contains no major changes, only minor corrections and clarifications of an editorial nature. This European Standard is one of a series of standards which specify test methods for determining dimensions and properties of thermal insulating materials and products. It supports a series of product standards for thermal insulating materials and products which derive from the Council Directive of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (Directive 89/106/EEC) through the consideration of the essential requirements. This European Standard has been drafted for applications in buildings but it may also be used in other areas where it is relevant. This European test standard is one of the following group of interrelated standards on test methods for determining dimensions and properties of thermal insulation materials and products, all of which fall within the scope of CEN/TC 88: EN 822, Thermal insulating products for building applications — Determination of length and width EN 823, Thermal insulating products for building applications — Determination of thickness EN 824, Thermal insulating products for building applications — Determination of squareness EN 825, Thermal insulating products for building applications — Determination of flatness EN 826, Thermal insulating products for building applications — Determination of compression behaviour EN 1602, Thermal insulating products for building applications — Determination of the apparent density EN 1603, Thermal insulating products for building applications — Determination of dimensional stability under constant normal laboratory conditions (23 °C/50 % relative humidity) EN 1604, Thermal insulating products for building applications — Determination of dimensional stability under specified temperature and humidity conditions EN 1605, Thermal insulating products for building applications — Determination of deformation under specified compressive load and temperature conditions EN 1606, Thermal insulating products for building applications — Determination of compressive creep SIST EN 12430:2013
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.