Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 5: Sheeters

This European Standard applies to sheeters, including unwinding units, sheet stacker, drive and control units
intended for use in paper making and shall be used together with EN 1034-1:2000. Paper dust and edge strip
suction devices are not covered by this standard. It deals with all significant hazards, hazardous situations and
hazard events relevant to sheeters, when they are used as intended and under the conditions foreseen by the
manufacturer (see clause 4). This standard does not apply to:
- sheeters for corrugated board (see EN 1010-5);
- sheeters for foil (see EN 1010-1);
- sheeters with sheet feeders (see EN 1010-1);
- guillotines (see EN 1010-3:2002).
This document is not applicable to sheeters that have been manufactured before the date of publication of this
document by CEN.

Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 5: Querschneider

Diese Europäische Norm gilt für Querschneider einschließlich Abrollungen, Einrichtung zur Bogenstapelung, Antrieb und Steuerung, die zur Verwendung bei der Papierherausrüstung bestimmt sind, und ist in Verbindung mit EN 1034-1:2000 anzuwenden werden. Anlagen zur Absaugung von Papierstaub und Randstreifen fallen nicht unter diese Norm. Sie behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf Querschneider zutreffen, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers verwendet werden (siehe Abschnitt 4). Diese Norm gilt nicht für:
-   Querschneider für Wellpappe (siehe EN 1010-5);
-   Querschneider für Folien (siehe EN 1010-1);
-   Querschneider mit Bogenanlegern (siehe EN 1010-1);
-   Planschneider (siehe EN 1010-3:2002).
Diese Europäische Norm gilt nicht für Querschneider, die hergestellt wurden, bevor CEN diese Europäische Norm veröffentlichte.

Sécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 5: Coupeuses

La présente Norme européenne s'applique aux coupeuses transversales comprenant unités de déroulage, dispositif pour l’empilage des feuilles, entraînement et système de commande, qui sont destinés à être employés lors de la finition du papier, et doit être appliquée conjointement avec l’EN 1034-1:2000. Les installations pour l’aspiration de la poussière de papier et des rognures ne rentrent pas dans le domaine d’application de cette norme. Elle traite de l’ensemble des phénomènes dangereux, situations dangereuses et événements dangereux qui concernent les coupeuses transversales lorsque celles-ci sont utilisées normalement et dans les conditions d’utilisation abusive qui peuvent raisonnablement être prévues par le fabricant (voir Article 4). Cette norme n’est pas applicable aux :
-   coupeuses transversales pour le carton ondulé (voir l’EN 1010-5) ;
-   coupeuses transversales pour les films en matière plastique ou en aluminium (voir l’EN 1010-1) ;
-   coupeuses transversales avec margeurs (voir l’EN 1010-1) ;
-   massicots (voir l'EN 1010-3:2002).
Cette Norme européenne n’est pas applicable aux coupeuses transversales qui ont été fabriquées avant sa publication par le CEN.

Varnost strojev – Varnostne zahteve za načrtovanje in konstrukcijo strojev in opreme za izdelavo papirja – 5. del: Rezalni stroji

General Information

Status
Withdrawn
Publication Date
20-Dec-2005
Withdrawal Date
01-Dec-2009
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
02-Dec-2009
Completion Date
02-Dec-2009

Relations

Buy Standard

Standard
EN 1034-5:2006
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 5: QuerschneiderSécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 5: CoupeusesSafety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 5: Sheeters85.100Oprema za papirno industrijoEquipment for the paper industry21.020Characteristics and design of machines, apparatus, equipment13.110Varnost strojevSafety of machineryICS:Ta slovenski standard je istoveten z:EN 1034-5:2005SIST EN 1034-5:2006en01-september-2006SIST EN 1034-5:2006SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1034-5December 2005ICS 85.100 English VersionSafety of machinery - Safety requirements for the design andconstruction of paper making and finishing machines - Part 5:SheetersSécurité des machines - Exigences techniques de sécuritépour la conception et la construction de machines defabrication et de finition du papier - Partie 5: CoupeusesSicherheit von Maschinen - SicherheitstechnischeAnforderungen an Konstruktion und Bau von Maschinender Papierherstellung und Ausrüstung - Teil 5:QuerschneiderThis European Standard was approved by CEN on 10 November 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1034-5:2005: ESIST EN 1034-5:2006

Muting of electro-sensitive protective equipment on paper making and finishing machines.22 Annex ZA (informative)
Relationship between this
European
Standard and the Essential Requirements
of EU Directive 98/37/EC.24 Bibliography.25
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard. For machines that have been designed and built according to the provisions of this type C standard, the following stipulation applies: when provisions of this type C standard are different from those which are stated in type A or B standards or from provisions made in EN 1034-1:2000, the provisions of this type C standard take precedence over the provisions of the other standards 1 Scope This European Standard applies to sheeters, including unwinding units, sheet stacker, drive and control units intended for use in paper making and shall be used together with EN 1034-1:2000. Paper dust and edge strip suction devices are not covered by this standard. It deals with all significant hazards, hazardous situations and hazard events relevant to sheeters, when they are used as intended and under the conditions foreseen by the manufacturer (see clause 4). This standard does not apply to:  sheeters for corrugated board (see EN 1010-5);  sheeters for foil (see EN 1010-1);  sheeters with sheet feeders (see EN 1010-1);  guillotines (see EN 1010-3:2002). This document is not applicable to sheeters that have been manufactured before the date of publication of this document by CEN. 2 Normative references The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any amendments) applies EN 294:1992, Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs EN 349:1993, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body EN 418:1992, Safety of machinery — Emergency stop equipment, functional aspects — Principles for design EN 563:1994 Safety of machinery — Temperatures of touchable surfaces — Ergonomics data to establish temperature limit values for hot surfaces EN 574:1996, Safety of machinery — Two-hand control devices — Functional aspects — Principles for design EN 626-1:1994, Safety of machinery — Reduction of risk to health from hazardous substances emitted by machinery — Part 1: Principles and specifications for machinery manufacturers SIST EN 1034-5:2006

(IEC 60204-1:1997) EN 61000-6-2:2001, Electromagnetic compatibility (EMC) — Part 6-2: Generic standards; immunity for industrial environment (IEC 61000-6-2:1999, modified) EN 61496-1:2004, Safe
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.