TC 96 - Transformers, reactors, power supply units, and combinations thereof
Standardization in the field of safety, EMC, EMF, energy efficiency and environmental aspects of transformers, reactors, power supply units, and combinations thereof. The standardization does not cover transformers, reactors and power supply units intended to be a part of distribution networks (covered by TC 14). TC 96 has group safety function in accordance with IEC Guide 104 for transformers other than those intended to supply distribution networks, in particular transformers and power supply units intended to allow the application of protective measures against electric shock as defined by TC 64, with no limitation of rated output power, but in certain cases including limitation of voltage. The general limitations for voltages are: - rated supply voltage not exceeding 1 000 V a.c.; - rated output voltage not exceeding 1 000 V a.c. or 1 500 V ripple free d.c.; however, internal voltages may exceed 1 000 V a.c. or 1 500 V ripple free d.c. For high-voltage applications, other than distribution networks (covered by TC 14), the rated output voltage can exceed 1 000 V a.c. or 1 500 V ripple free d.c. but the no load output voltage shall not exceed 15 000 V a.c. or 15 000 V d.c. The general limitations for the rated output are: - The maximum rated output depends on the type of transformer or linear power supply unit does in most cases not exceed 25 kVA for single-phase products and 40 kVA for three phase products; - the maximum rated output does not exceed 1 kVA for both single-phase and three phase Switch Mode Power Supplies; - the general limitations for the rated core power are 25 kVA for single-phase auto transformers and 40 kVA for three phase auto transformers; - the general limitations for the rated power are 50 kvar for single-phase reactors and 80 kvar for three phase reactors. For special transformers, reactors and power supply units and combinations thereof there are no limitation of rated output, rated core power and rated power.
Transformateurs, bobines d'inductance, blocs d'alimentation et combinaisons de ces éléments
Normalisation dans le domaine de la sécurité, de la compatibilité électromagnétique, des champs électromagnétiques, de l’efficacité énergétique et des aspects environnementaux des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments. Les transformateurs, bobines d’inductance et blocs d’alimentation destinés aux réseaux de distribution ne sont pas inclus dans le domaine d’application (couverts par le CE 14). Le CE 96 a une fonction groupée de sécurité en accord avec le Guide 104 pour les transformateurs autres que ceux destinés à l’alimentation des réseaux de distribution, en particulier les transformateurs et les blocs d’alimentation destinés à permettre l’application des mesures de protection contre les chocs électriques telles que définies par le CE 64 « Titre », sans limitation de la puissance secondaire assignée, mais dans certains cas avec une limitation de la tension. Les limitations pour la tension sont : - tension primaire assignée ne dépassant pas 1 000 V en courant alternatif; - tension secondaire assignée ne dépassant pas 1 000 V en courant alternatif ou 1 500 V en courant continu lissé; cependant, certaines tensions internes peuvent dépasser 1 000 V en courant alternatif ou 1 500 V en courant continu lissé. Pour les applications haute-tension, autres que celles des réseaux de distribution (couverts par le CE 14), la tension secondaire assignée peut dépasser 1 000 V en courant alternatif ou 1 500 V en courant continu lissé mais la tension secondaire à vide ne doit pas dépasser 15 000 V en courant alternatif ou 15 000 V en courant continu lissé.
General Information
IEC 61558-2-5:2024 deals with the safety of shaver transformers, power supply units incorporating a shaver transformer, and shaver supply units. Shaver transformers incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) adjustment of structure and references in accordance with IEC 61558-1:2017;
b) new symbol for power supply unit with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard57 pagesEnglish languagesale 15% off
- Standard211 pagesEnglish languagesale 15% off
- Standard38 pagesEnglish and French languagesale 15% off
IEC 61558-2-9:2024 deals with the safety of transformers for class III handlamps and power supply units incorporating transformers for class III handlamps. Transformers incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) adjustment of structure and references in accordance with IEC 61558-1:2017;
b) addition of a new symbol for power supply unit with linearly regulated output voltage;
c) document is not only valid for transformers for tungsten filament handlamps.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard52 pagesEnglish languagesale 15% off
- Standard206 pagesEnglish languagesale 15% off
- Standard34 pagesEnglish and French languagesale 15% off
IEC 61558-2-10:2024 deals with the safety of separating transformers with high insulation level and separating transformers with output voltages exceeding 1 000 V. Transformers incorporating electronic circuits are also covered by this document. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) adjustment of structure and references in accordance with IEC 61558-1:2017;
b) overvoltage categories I, II, III and IV for clearances and dielectric strength tests are included;
c) clearances for homogenous field conditions deleted.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard61 pagesEnglish languagesale 15% off
- Standard213 pagesEnglish languagesale 15% off
- Standard39 pagesEnglish and French languagesale 15% off
IEC 61558-2-8:2024 deals with the safety of bell and chime transformers and power supply units incorporating bell and chime transformers. Transformers incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) adjustment of structure and references in accordance with IEC 61558-1:2017;
b) new symbol for power supply unit with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard56 pagesEnglish languagesale 15% off
- Standard207 pagesEnglish languagesale 15% off
- Standard37 pagesEnglish and French languagesale 15% off
IEC 61558-2-23:2024 deals with the safety of transformers for construction sites and power supply units incorporating transformers for construction sites. Transformers incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) adjustment of structure and references in accordance with IEC 61558-1:2017;
b) new symbol for power supply units with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard68 pagesEnglish languagesale 15% off
- Standard223 pagesEnglish languagesale 15% off
- Standard45 pagesEnglish and French languagesale 15% off
IEC 61558-2-12:2024 deals with the safety of constant voltage transformers for general applications and power supply units for constant voltage for general applications. Constant voltage transformers incorporating electronic circuits are also covered by this document.
This third edition cancels and replaces the second edition published in 2011. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) adjustment of structure and references in accordance with IEC 61558-1:2017;
b) description of constructions moved to IEC 61558-1:2017;
c) new symbol for power supply unit with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard66 pagesEnglish languagesale 15% off
- Standard219 pagesEnglish languagesale 15% off
- Standard41 pagesEnglish and French languagesale 15% off
IEC 61558-2-16:2021 deals with the safety of switch mode power supply units and transformers for switch mode power supply units.
This second edition cancels and replaces the first edition published in 2009 and amendment 1:2013. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
adjustment of structure and references in accordance with IEC 61558-1:2017;
definitions of different voltage characteristics;
partial discharge and description of constructions moved to IEC 61558-1:2017;
alternative method for dimensioning of clearances;
removal of requirements for homogeneous field conditions.
It has the status of a group safety publication in accordance with IEC Guide 104.
This International Standard is to be used in conjunction with IEC 61558-1:2017.
- Standard1 pageEnglish and French languagesale 15% off
This part of IEC 61558 deals with the safety of ignition transformers for gas and oil burners. Ignition transformers incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) adjustment of structure and references in accordance with IEC 61558-1:2017.
It has the status of a group safety publication in accordance with IEC Guide 104. The contents of the corrigendum 1 (2023-09) have been included in this copy.
- Standard62 pagesEnglish languagesale 15% off
- Standard211 pagesEnglish languagesale 15% off
- Standard273 pagesEnglish languagesale 15% off
- Standard273 pagesEnglish languagesale 15% off
- Standard40 pagesEnglish and French languagesale 15% off
IEC 61558-2-7:2023 deals with the safety of transformers for toys and power supply units incorporating transformers for toys. Transformers for toys incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) adjustment of structure and references in accordance with IEC 61558-1:2017;
b) new symbol for power supply unit with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard64 pagesEnglish languagesale 15% off
- Standard215 pagesEnglish languagesale 15% off
- Standard41 pagesEnglish and French languagesale 15% off
IEC 61558-2-20:2022 deals with the safety of small reactors for general applications. Small reactors incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- adjustment of structure and references in accordance with IEC 61558-1:2017.
- additional Annex AA with references for characteristic parameter measurements.
- additional Annex BB for associated reactors with frequencies above 500 Hz.
- additional Annex CC for partial discharge.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard70 pagesEnglish languagesale 15% off
- Standard46 pagesEnglish and French languagesale 15% off
IEC 61558-2-13:2022 deals with the safety of auto-transformers for general applications and power supply units incorporating auto-transformers for general applications. Transformers incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- adjustment of structure and references in accordance with IEC 61558-1:2017;
- description of constructions moved to IEC 61558-1:2017;
- new symbol for power supply unit with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard49 pagesEnglish languagesale 15% off
- Standard207 pagesEnglish languagesale 15% off
- Standard31 pagesEnglish and French languagesale 15% off
IEC 61558-2-2:2022 deals with the safety of control transformers and power supply units incorporating control transformers. Transformers incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- adjustment of structure and references in accordance with IEC 61558-1:2017;
- new general symbol for control transformers;
- new symbol for power supply unit with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard53 pagesEnglish languagesale 15% off
- Standard210 pagesEnglish languagesale 15% off
- Standard34 pagesEnglish and French languagesale 15% off
IEC 61558-2-14:2022 deals with the safety of variable transformers for general applications and power supply units incorporating variable transformers for general applications. Transformers incorporating electronic circuits are also covered by this document. This second edition cancels and replaces the first edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- adjustment of structure and references in accordance with IEC 61558-1:2017;
- description of constructions moved to IEC 61558-1:2017;
- new symbols for power supply units with linearly regulated output voltages and required current collector position changes.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard61 pagesEnglish languagesale 15% off
- Standard37 pagesEnglish and French languagesale 15% off
IEC 61558-2-15:2022 deals with safety of isolating transformers for medical IT systems for the supply of medical locations. This third edition cancels and replaces the second edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Adjustment of structure and references in accordance with IEC 61558-1:2017.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard66 pagesEnglish languagesale 15% off
- Standard207 pagesEnglish languagesale 15% off
- Standard42 pagesEnglish and French languagesale 15% off
IEC 61558-2-16:2021 deals with the safety of switch mode power supply units and transformers for switch mode power supply units. This second edition cancels and replaces the first edition published in 2009 and amendment 1:2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- adjustment of structure and references in accordance with IEC 61558-1:2017;
- definitions of different voltage characteristics;
- partial discharge and description of constructions moved to IEC 61558-1:2017;
- alternative method for dimensioning of clearances;
- removal of requirements for homogeneous field conditions.
It has the status of a group safety publication in accordance with IEC Guide 104. This International Standard is to be used in conjunction with IEC 61558-1:2017. The contents of the corrigendum 1 (2023-09) have been included in this copy.
- Standard80 pagesEnglish and French languagesale 15% off
IEC 61558-2-6:2021 deals with the safety of safety isolating transformers for general applications and power supply units incorporating safety isolating transformers for general applications. Transformers incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision.
- adjustment of structure and references in accordance with IEC 61558-1:2017;
- description of constructions moved in IEC 61558-1:2017;
- new symbol for power supply unit with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
This International Standard is to be used in conjunction with IEC 61558-1:2017.
- Standard15 pagesEnglish languagesale 15% off
- Standard33 pagesEnglish languagesale 15% off
IEC 61558-2-4:2021 deals with the safety of isolating transformers for general applications and power supply units incorporating isolating transformers for general applications. Transformers incorporating electronic circuits are also covered by this document. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- adjustment of structure and references in accordance with IEC 61558-1:2017;
- description of constructions moved to IEC 61558-1:2017;
- a new symbol for power supply unit with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
This International Standard is to be used in conjunction with IEC 61558-1:2017.
- Standard15 pagesEnglish languagesale 15% off
- Standard33 pagesEnglish languagesale 15% off
IEC 61558-2-1:2021 deals with the safety of separating transformers for general applications and power supply units incorporating separating transformers for general applications. Transformers incorporating electronic circuits are also covered by this document.
This third edition cancels and replaces the second edition published in 2007. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Adjustment of structure and references in accordance with IEC 61558-1:2017;
b) Description of constructions moved to IEC 61558-1:2017;
c) New symbol for power supply unit with linearly regulated output voltage.
It has the status of a group safety publication in accordance with IEC Guide 104.
This International Standard is to be used in conjunction with IEC 61558-1:2017.
- Standard14 pagesEnglish languagesale 15% off
IEC 61558-1:2017 deals with safety aspects of transformers, reactors, power supply units and combinations thereof such as electrical, thermal and mechanical safety. This document covers the following independent or associated stationary or portable types of dry-type transformers, power supply units, including switch mode power supply units, reactors and combinations thereof in the field of safety. The windings can be encapsulated or non-encapsulated. They are not forming a part of the distribution network. This third edition cancels and replaces the second edition published in 2005 and Amendment 1:2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a. fully insulated winding wires (FIW), new tables and aging tests for FIW constructions,
b. overvoltage categories 1, 2, 3 and 4 for clearances and dielectric strength tests (new tables) are included,
c. development of new symbols for the different overvoltage categories,
d. symbol for maximum altitudes, if higher than 2 000 m,
e. symbol for plug in power supply units, if the pins are damaged (tumbling barrel test),
f. symbol for minimum temperature (even during the transportation),
g. alternative temperature measurement, simulated load and back to back method according to IEC 60076-11,
h. short circuit and overload protection, simulated load and back to back method according to IEC 60076-11,
i. adjustment of temperatures in Table 2 according to CENELEC Guide 29,
j. establishing partial discharge test above 750 V for FIW constructions,
k. requirements for toroidal core constructions, division for basic and for supplementary isolation,
l. modification of protection indexes for enclosures (IP-code),
m. dimensioning of rectangular cross section connectors for transformers,
n. repetition test, 80% of required dielectric strength test voltage of Table 14,a.
o. vibration test for vehicles and railway applications,
p. two Y1 Capacitors for working voltages above 250 V and not exceeding 500 V with overvoltage category 3.
It has the status of a group safety publication in accordance with IEC Guide 104.
- Standard556 pagesEnglish languagesale 15% off
- Standard356 pagesEnglish and French languagesale 15% off
IEC 62041: 2017 is applicable to transformers, reactors and power supply units covered by the IEC 61558 series of standards. This document deals with the electromagnetic compatibility requirements for emission and immunity within the frequency range 0 Hz to 400 GHz. No tests need to be performed at frequencies where no requirements are specified.
This third edition cancels and replaces the second edition published in 2010. It constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
the inclusion of a clause on tests in series production;
the inclusion of a new clause on measurement uncertainly, and
the status of a harmonized standard for this third edition.
It has the status of a product family EMC standard in accordance with IEC Guide 107:2009,
Electromagnetic compatibility – Guide to the drafting of electromagnetic compatibility publications.
- Standard30 pagesEnglish languagesale 15% off
- Standard62 pagesEnglish and French languagesale 15% off
IEC 61558-2-10:2014 deals with the safety of separating transformers with high insulation level and separating transformers with output voltages exceeding 1 000 V. Transformers incorporating electronic circuits are also covered by this standard. This first edition cancels and replaces Chapter ll Section Three of IEC 60989 published in 1991. It constitutes a technical revision. The main changes consist of
a) updating this part in accordance with IEC 61558-1:2005, and
b) adding power supply units to the scope. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. The transitional period is not longer than 3 years after the publication of this standard.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard33 pagesEnglish and French languagesale 15% off
- Standard25 pagesEnglish and French languagesale 15% off
IEC 61558-2-26:2013 deals with the safety of transformers, power supply units and switch mode power supply units all for saving energy and other purposes in electrical installations by adjusting the output voltage and/or other electrical characteristics on the output circuits without interruption affected by the transformers, power supply unit and switch mode power supply unit. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip them for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard38 pagesEnglish and French languagesale 15% off
IEC 61558-2-14:2012 deals with safety of variable transformers for general applications and power supply units incorporating variable transformers for general applications. Transformers incorporating electronic circuits are also covered by this standard. This first edition cancels and replaces the chapter IV of the IEC 60989 published in 1991. It is a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) update of the existing text;
b) complete editorial review.
This part has the status of a group safety publication in accordance with IEC Guide 104:2010. The preparation of safety publications and the use of basic safety publications and group safety publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard46 pagesEnglish and French languagesale 15% off
IEC 61558-2-15:2011 deals with safety aspects of isolating transformers for the supply of medical locations. This second edition cancels and replaces the first edition published in 1999. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104:2010. The preparation of safety publications and the use of basic safety publications and group safety publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard37 pagesEnglish and French languagesale 15% off
- Standard10 pagesEnglish and French languagesale 15% off
IEC 61558-2-12:2011 deals with the safety of constant voltage transformers for general applications and power supply units for constant voltage for general applications. Constant voltage transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 2001. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2009. This part has the status of a group safety publication in accordance with IEC Guide 104: The preparation of safety publications and the use of basic safety publications and group safety publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard42 pagesEnglish and French languagesale 15% off
IEC 61558-2-23:2010 deals with the safety of transformers for construction sites and power supply units incorporating transformers for construction sites. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 2000. It constitutes a technical revision. The main changes consist of updating this Part 2-23 in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104: The preparation of safety publications and the use of basic safety publications and group safety publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.
- Standard41 pagesEnglish and French languagesale 15% off
IEC 62041:2010 applies to transformers, reactors, power supply units and combinations thereof covered by the IEC 61558 series of standards. This standard deals with the electromagnetic compatibility requirements for emission and immunity within the frequency range 0 Hz - 400 GHz. No measurement needs to be performed at frequencies where no requirement is specified. This second edition cancels and replaces the first edition published in 2003. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- the frequency range for tests according to IEC 61000-4-3 has been extended above 1 GHz according to technologies used in this frequency area;
- the testing requirements according to IEC 61000-4-11 have been amended significantly;
- the inclusion of a clause on tests in series production;
- the inclusion of a new clause on measurement uncertainly, and
- the inclusion of requirements on DC power ports and telecommunication ports.
It has the status of a product family EMC standard in accordance with IEC Guide 107:2009, Electromagnetic compatibility - Guide to the drafting of electromagnetic compatibility publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.
- Standard38 pagesEnglish and French languagesale 15% off
IEC 61558-2-20:2010 deals with the safety of small reactors for general applications. This part is applicable to stationary or portable, single-phase or polyphase, air-cooled (natural or forced) general purpose reactors including alternating current, premagnetised and current compensated independent or associated reactors. This second edition cancels and replaces the first edition published in 2000. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard34 pagesEnglish and French languagesale 15% off
IEC 61558-2-8:2010 deals with the safety of bell and chime transformers and power supply units incorporating bell and chime transformers. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 1998. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard29 pagesEnglish and French languagesale 15% off
IEC 61558-2-3:2010 deals with the safety of ignition transformers for gas and oil burners. Ignition transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 1999. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard34 pagesEnglish and French languagesale 15% off
IEC 61558-2-9:2010 deals with the safety of transformers for class III handlamps for tungsten filament lamps and power supply units incorporating transformers for class III handlamps for tungsten filament lamps. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 2002. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005, and adding power supply units to the scope. This part has the status of a group safety publication in accordance with IEC Guide 104. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard26 pagesEnglish and French languagesale 15% off
IEC 61558-2-5:2010 deals with the safety of shaver transformers, power supply units incorporating a shaver transformer, and shaver supply units. Shaver transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 1997. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005 and adding power supply units to the scope. This part has the status of a group safety publication in accordance with IEC Guide 104. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.
This publication is to be read in conjunction with IEC 61558-1:2005.
- Standard30 pagesEnglish and French languagesale 15% off
This publication has the status of a technical report - type 2.
- Standard10 pagesEnglish and French languagesale 15% off
IEC 61558-2-16:2009 deals with the safety of switch mode power supply units and transformers for switch mode power supply units. Transformers incorporating electronic circuits are also covered by this standard. This Part 2-16 is intended to be used in conjunction with the latest edition of IEC 61558-1 and its amendments. It is based on the second edition (2005) of that standard. This first edition of IEC 61558-2-16 cancels and replaces IEC 61558-2-17, published in 1997. It constitutes a technical revision. This part has the status of a group safety publication in accordance with IEC Guide 104 (1997): The preparation of safety publications and the use of basic safety publications and group safety publications.
- Standard70 pagesEnglish and French languagesale 15% off
- Standard187 pagesEnglish and French languagesale 15% off
This International Standard deals with safety aspects of power transformers, power supplies, reactors and similar products such as electrical, thermal and mechanical safety. This standard covers the following types of dry-type transformers, power supplies, including switch mode power supplies, and reactors, the windings of which may be encapsulated or non-encapsulated It has the status of a group safety publication in accordance with IEC Guide 104. The contents of the corrigenda of March 2008, March 2010 and April 2011 have been included in this copy.
- Standard321 pagesEnglish and French languagesale 15% off
- Standard321 pagesEnglish and French languagesale 15% off
IEC 61558-2-4:2009 deals with the safety of isolating transformers for general applications and power supply units incorporating isolating transformers for general applications. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 1997. It constitutes a technical revision. The main changes consist of updating this part in accordance with Part 1 (2005), and increasing the supply voltages up to 1 100 V to be in line with the standards of TC 14. This part has the status of a group safety publication in accordance with IEC Guide 104. This part is intended to be used in conjunction with the latest edition of IEC 61558-1 and its amendments. It is based on the second edition (2005) of that standard. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication.
- Standard29 pagesEnglish and French languagesale 15% off
IEC 61558-2-6:2009 deals with the safety of safety isolating transformers for general applications and power supply units incorporating safety isolating transformers for general applications. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 1997. It constitutes a technical revision. The main changes consist of updating this part in accordance with Part 1 (2005), and increasing the supply voltages up to 1 100 V to be in line with the standards of TC 14. This part has the status of a group safety publication in accordance with IEC Guide 104. This part is intended to be used in conjunction with the latest edition of IEC 61558-1 and its amendments. It is based on the second edition (2005) of that standard. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication.
- Standard28 pagesEnglish and French languagesale 15% off
IEC 61558-2-13:2009 deals with the safety of auto transformers for general applications and power supply units incorporating auto transformers for general applications. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 1999. It constitutes a technical revision. The main changes consist of updating this part in accordance with Part 1 (2005), and increasing the supply voltages up to 1 100 V to be in line with the standards of TC 14. This part has the status of a group safety publication in accordance with IEC Guide 104. This part is intended to be used in conjunction with the latest edition of IEC 61558-1 and its amendments. It is based on the second edition (2005) of that standard. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication.
- Standard29 pagesEnglish and French languagesale 15% off
- Standard4 pagesEnglish and French languagesale 15% off
Applies to insulating hollow tubes made of synthetic materials and intended for tools and equipment for work on systems operating at voltages above 1 kV.[
]The contents of the corrigenda of July 1999 and May 2000 have been included in this copy.
- Standard10 pagesEnglish and French languagesale 15% off
This part of IEC 61558 deals with safety aspects of separating transformers and power supplies incorporating separating transformers such as electrical, thermal and mechanical safety. This second edition cancels and replaces the first edition published in 1997. It constitutes a technical revision. The main changes consist of updating this Part 2-1 in accordance with Part 1 edition 2, and adding power supplies to the scope. This Part 2-1 has the status of a group safety publication in accordance with IEC Guide 104.
- Standard23 pagesEnglish and French languagesale 15% off
This part of IEC 61558 deals with safety aspects of transformers for toys and power supplies incorporating transformers for toys such as electrical, thermal and mechanical safety. This second edition cancels and replaces the first edition published in 1997. It constitutes a technical revision. The main changes consist of updating this Part 2-7, in accordance with Part 1, edition 2, and adding power supplies to the scope. This Part 2-7 has the status of a group safety publication in accordance with IEC Guide 104.
- Standard35 pagesEnglish and French languagesale 15% off
This part of IEC 61558 deals with safety aspects of control transformers and power supplies incorporating control transformers such as electrical, thermal and mechanical safety This second edition cancels and replaces the first edition published in 1997. It constitutes a technical revision. The main changes consist of updating this Part 2-2 in accordance with Part 1, edition 2, and adding power supplies to the scope. This Part 2-2 has the status of a group safety publication in accordance with IEC Guide 104.
- Standard27 pagesEnglish and French languagesale 15% off
Interpretation of subclause 19.8
- Standard10 pagesEnglish languagesale 15% off
This international product family standard applies to independent transformers, reactors and power supply units covered by IEC 60989 and the IEC 61558 series of standards. It prescribes the electromagnetic compatibility requirements for emission and immunity in the frequency range 0 Hz to 1 000 MHz.
- Standard27 pagesEnglish and French languagesale 15% off
This Part 2-9 of IEC 61558 applies to stationary or portable single-phase air-cooled (natural or forced) associated safety isolating transformers for class III handlamps for tungsten filament lamps, having a rated supply voltage not exceeding 1 000 V a.c., a rated frequency not exceeding 500 Hz and a rated output not exceeding 10 kVA. It has the status of a group safety publication in accordance with IEC Guide 104
- Standard27 pagesEnglish and French languagesale 15% off
This part 2 of IEC 61558 is intended to be used in conjunction with IEC 61558-1. This international standard deals with all aspects of safety such as electrical, thermal and mechanical. This part of IEC 61558 applies to stationary or portable, single-phase or polyphase, air-cooled (natural or forced), associated or independent: - constant voltage auto-transformers; - constant voltage separating transformers; - constant voltage isolating transformers; - constant voltage safety isolating transformers; having a rated supply voltage not exceeding 1 000 V a.c., a rated frequency not exceeding 500 Hz, an internal operational frequency not exceeding 30 kHz and no limitation of the rated output. It has the status of a group safety publication in accordance with IEC Guide 104
- Standard37 pagesEnglish and French languagesale 15% off