SIST EN 1113:2015
(Main)Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
This European Standard specifies:
- the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower hoses should comply;
- the procedures for testing these characteristics.
This European Standard applies to shower hoses of any material used for ablutionary purposes and intended for equipping and supplementing sanitary tapware for baths and showers.
This European Standard applies to shower hoses connected downstream of the obturator of the tapware.
Hoses which are an integral part of sanitary tapware (sink and wash basin mixing valves) or hoses intended to connect sanitary tapware to the water supplies are not covered by this European Standard.
Details of pressures and temperatures are given in Table 1.
Sanitärarmaturen - Brauseschläuche für Sanitärarmaturen für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische Spezifikation
Diese Europäische Norm legt Folgendes fest:
Maße und Dichtheit sowie mechanisches und hydraulisches Verhalten, die/das Brauseschläuche aufweisen sollten;
die Verfahren zur Prüfung auf Einhaltung dieser Anforderungen.
Die vorliegende Europäische Norm gilt unabhängig vom verwendeten Werkstoff für Brauseschläuche für die Körperhygiene als Ausrüstung und Ergänzung von Sanitärarmaturen in Duschen und Bädern.
Diese Europäische Norm gilt für Brauseschläuche für den Anschluss nach dem Absperrorgan der Armatur.
Diese Europäische Norm deckt keine Schläuche zur Verbindung der Sanitärarmaturen mit der Wasserver-sorgung und keine Schläuche ab, die integraler Bestandteil der Sanitärarmatur sind (Mischbatterien für Spülbecken und Handwaschbecken).
Einzelheiten zu Druck und Temperatur sind in Tabelle 1 enthalten.
Robinetterie sanitaire - Flexibles de douches pour robinetterie sanitaire pour les systèmes d`alimentation type 1 et type 2 - Spécifications techniques générales
La présente Norme européenne spécifie :
les caractéristiques dimensionnelles, d’étanchéité, de comportement mécanique et hydraulique auxquelles il convient que les flexibles de douches répondent ;
les modes opératoires d’essai permettant de contrôler ces caractéristiques.
La présente Norme européenne s’applique aux flexibles de douches, quel que soit le matériau utilisé, destinés à équiper et à compléter les robinetteries sanitaires de baignoires ou de douches réservées pour l’hygiène corporelle.
La présente Norme européenne s’applique aux flexibles de douches connectés en aval de l’obturateur de la robinetterie.
Les flexibles destinés à raccorder les robinetteries sanitaires à l’installation, ainsi que ceux qui font partie de la robinetterie (mitigeurs pour évier et lavabo) ne sont pas couverts par la présente Norme européenne.
Les exigences relatives à la pression et à la température sont données dans le Tableau 1.
Sanitarne armature - Gibke cevi za sanitarne armature sistemov za oskrbo z vodo tipa 1 in tipa 2 - Splošne tehnične zahteve
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sanitärarmaturen - Brauseschläuche für Sanitärarmaturen für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische SpezifikationRobinetterie sanitaire - Flexibles de douches pour robinetterie sanitaire pour les systèmes d`alimentation type 1 et type 2 - Spécifications techniques généralesSanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification91.140.70Sanitarne napraveSanitary installations23.040.70Gumene cevi in armatureHoses and hose assembliesICS:Ta slovenski standard je istoveten z:EN 1113:2015SIST EN 1113:2015en,fr,de01-junij-2015SIST EN 1113:2015SLOVENSKI
STANDARDSIST EN 1113:2009+A1:20111DGRPHãþD
SIST EN 1113:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1113
April 2015 ICS 23.040.70; 91.140.70 Supersedes EN 1113:2008+A1:2011English Version
Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
Robinetterie sanitaire - Flexibles de douches pour robinetterie sanitaire pour les systèmes d`alimentation type 1 et type 2 - Spécifications techniques générales
Sanitärarmaturen - Brauseschläuche für Sanitärarmaturen für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische Spezifikation This European Standard was approved by CEN on 12 March 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1113:2015 ESIST EN 1113:2015
EN 1113:2015 (E) 2 Contents Foreword .4 Introduction .5 1 Scope .6 2 Normative references .9 3 Terms and definitions .9 4 Designation .9 5 Marking .9 6 Materials .9 6.1 Chemical and hygienic requirements .9 6.2 Exposed surface condition and quality of coating . 10 7 Dimensional characteristics . 10 7.1 General . 10 7.2 Connecting dimensions . 10 7.3 Special cases . 11 8 Hydraulic characteristics . 11 8.1 General . 11 8.2 Flow rate . 12 8.2.1 Test method . 12 8.2.2 Principle . 12 8.2.3 Apparatus . 12 8.2.4 Procedure . 12 8.2.5 Requirements . 12 9 Mechanical and leaktightness characteristics . 14 9.1 General . 14 9.2 Tensile strength . 14 9.2.1 Test method . 14 9.2.2 Principle . 14 9.2.3 Apparatus . 14 9.2.4 Procedure . 15 9.2.5 Requirements . 15 9.3 Resistance to flexing . 15 9.3.1 Test Method . 15 9.3.2 Principle . 15 9.3.3 Apparatus . 15 9.3.4 Procedure . 17 9.3.5 Requirement . 17 9.4 Pressure resistance at elevated temperature . 17 9.4.1 Test method . 17 9.4.2 Principle . 17 9.4.3 Apparatus . 18 9.4.4 Procedure . 18 9.4.5 Requirements . 19 9.5 Leaktightness after tensile strength and resistance to flexing tests . 19 9.5.1 Test method . 19 9.5.2 Principle . 19 SIST EN 1113:2015
EN 1113:2015 (E) 3 9.5.3 Apparatus . 19 9.5.4 Procedure . 19 9.5.5 Requirements . 19 9.6 Thermal shock test . 19 9.6.1 Test method . 19 9.6.2 Principle . 19 9.6.3 Apparatus . 19 9.6.4 Procedure . 20 9.6.5 Requirements . 20 10 Rotary connection . 20 10.1 General . 20 10.2 Test Method . 21 10.2.1 Principle . 21 10.2.2 Apparatus . 21 10.2.3 Procedure . 21 10.2.4 Requirement . 22 Bibliography . 23 SIST EN 1113:2015
EN 1113:2015 (E) 4 Foreword This document (EN 1113:2015) has been prepared by Technical Committee CEN/TC 164 “Water supply”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2015, and conflicting national standards shall be withdrawn at the latest by October 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1113:2008+A1:2011. The main change to this standard is the introduction of 2 classes for hoses for supply systems of type 1. See Table 1 and Table 3. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 1113:2015
EN 1113:2015 (E) 5 Introduction In respect of potential adverse effects on the quality of water intended for human consumption caused by the product covered by this European Standard: — This European Standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA. — While awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of this product remain in force. SIST EN 1113:2015
EN 1113:2015 (E) 6 1 Scope This European Standard specifies: — the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower hoses should comply; — the procedures for testing these characteristics. This European Standard applies to shower hoses of any material used for ablutionary purposes and intended for equipping and supplementing sanitary tapware for baths and showers. This European Standard applies to shower hoses connected downstream of the obturator of the tapware. Hoses which are an integral part of sanitary tapware (sink and wash basin mixing valves) or hoses intended to connect sanitary tapware to the water supplies are not covered by this European Standard. Details of pressures and temperatures are given in Table 1. Table 1 — Conditions of use/Classifications Water Supply
system Operating range of shower hoses Flow rates Limits Recommended See Table 3 Type 1
see Figure 1 Dynamic Pressure (0,05 to 0,5) MPa [(0,5 to 5) bar] Dynamic Pressure (0,1 to 0,3) MPa [(1,0 to 3,0) bar] Class 1 0,42 l/s ≤ Q (25,2 l/min ≤ Q)
at (0,0200,3+) MPa [(0,203+) bar] Class 2 0,20 l/s ≤ Q < 0,42 l/s (12 l/min ≤ Q < 25,2 l/min)
at (0,0200,3+) MPa [(0,203+) bar] Type 2
see Figure 2 Dynamic Pressure (0,
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sanitärarmaturen - Brauseschläuche für Sanitärarmaturen für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische SpezifikationRobinetterie sanitaire - Flexibles de douches pour robinetterie sanitaire pour les systèmes d`alimentation type 1 et type 2 - Spécifications techniques généralesSanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification91.140.70Sanitarne napraveSanitary installations23.040.70Gumene cevi in armatureHoses and hose assembliesICS:Ta slovenski standard je istoveten z:FprEN 1113kSIST FprEN 1113:2014en,fr,de01-november-2014kSIST FprEN 1113:2014SLOVENSKI
STANDARD
kSIST FprEN 1113:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 1113
September 2014 ICS 23.040.70; 91.140.70 Will supersede EN 1113:2008+A1:2011English Version
Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
Robinetterie sanitaire - Flexibles de douches pour robinetterie sanitaire pour les systèmes d`alimentation type 1 et type 2 - Spécifications techniques générales
Sanitärarmaturen - Brauseschläuche für Sanitärarmaturen für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische Spezifikation This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 164.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 1113:2014 EkSIST FprEN 1113:2014
FprEN 1113:2014 (E) 2 Contents Foreword .4 Introduction .5 1 Scope .6 2 Normative references .9 3 Terms and definitions .9 4 Designation .9 5 Marking .9 6 Materials .9 6.1 Chemical and hygienic requirements .9 6.2 Exposed surface condition and quality of coating . 10 7 Dimensional characteristics . 10 7.1 General . 10 7.2 Connecting dimensions . 10 7.3 Special cases . 11 8 Hydraulic characteristics . 11 8.1 General . 11 8.2 Flow rate . 12 8.2.1 Test method . 12 8.2.2 Principle . 12 8.2.3 Apparatus . 12 8.2.4 Procedure . 12 8.2.5 Requirements . 12 9 Mechanical and leaktightness characteristics . 14 9.1 General . 14 9.2 Tensile strength . 14 9.2.1 Test method . 14 9.2.2 Principle . 14 9.2.3 Apparatus . 14 9.2.4 Procedure . 15 9.2.5 Requirements . 15 9.3 Resistance to flexing . 15 9.3.1 Test Method . 15 9.3.2 Principle . 15 9.3.3 Apparatus . 15 9.3.4 Procedure . 17 9.3.5 Requirement . 17 9.4 Pressure resistance at elevated temperature . 17 9.4.1 Test method . 17 9.4.2 Principle . 17 9.4.3 Apparatus . 18 9.4.4 Procedure . 18 9.4.5 Requirements . 19 9.5 Leaktightness after tensile strength and resistance to flexing tests . 19 9.5.1 Test method . 19 9.5.2 Principle . 19 kSIST FprEN 1113:2014
FprEN 1113:2014 (E) 3 9.5.3 Apparatus . 19 9.5.4 Procedure . 19 9.5.5 Requirements . 19 9.6 Thermal shock test . 19 9.6.1 Test method . 19 9.6.2 Principle . 19 9.6.3 Apparatus . 19 9.6.4 Procedure . 20 9.6.5 Requirements . 20 10 Rotary connection . 20 10.1 General . 20 10.2 Test Method . 21 10.2.1 Principle . 21 10.2.2 Apparatus . 21 10.2.3 Procedure . 21 10.2.4 Requirement . 22 Bibliography . 23 kSIST FprEN 1113:2014
FprEN 1113:2014 (E) 4 Foreword This document (FprEN 1113:2014) has been prepared by Technical Committee CEN/TC 164 “Water supply”, the secretariat of which is held by AFNOR. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 1113:2008+A1:2011. The main change to this standard is the introduction of 2 classes for hoses for supply systems of type 1. See Table 1 and Table 3. kSIST FprEN 1113:2014
FprEN 1113:2014 (E) 5 Introduction In respect of potential adverse effects on the quality of water intended for human consumption caused by the product covered by this standard: — This standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA. — While awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of this product remain in force. kSIST FprEN 1113:2014
FprEN 1113:2014 (E) 6 1 Scope This European Standard specifies: — the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower hoses should comply; — the procedures for testing these characteristics. This European Standard applies to shower hoses of any material used for ablutionary purposes and intended for equipping and supplementing sanitary tapware for baths and showers. This European Standard applies to shower hoses connected downstream of the obturator of the tapware. Hoses which are an integral part of sanitary tapware (sink and wash basin mixing valves) or hoses intended to connect sanitary tapware to the water supplies are not covered by this European Standard. Details of pressures and temperatures are given in Table 1. Table 1 — Conditions of use/Classifications Water Supply
system Operating range of shower hoses Flow rates Limits Recommended See Table 3 Type 1
see Figure 1 Dynamic Pressure (0,05 to 0,5) MPa [(0,5 to 5) bar] Dynamic Pressure (0,1 to 0,3) MPa [(1,0 to 3,0) bar] Class 1 0,42 l/s ≤ Q (25,2 l/min ≤ Q)
at (0,0200,3+) MPa [(0,203+) bar] Class 2 0,20 l/s ≤ Q < 0,42 l/s (12 l/min ≤ Q < 25,2 l/min)
at (0,0200,3+) MPa [(0,203+) bar] Type 2
see Figure 2 Dynamic Pressure (0,01 to 0,2) MPa [(0,1 to 2) bar] Dynamic Pressure (0,02 to 0,10) MPa [(0,2 to 1,0) bar] Class E 0,06 l/s < Q < 0,18 l/s (3,6 l/min < Q < 10,8 l/min.) at (0,000500,01+) MPa [(0,00500,1+) bar] Class H 0,18 l/s ≤ Q (10,8 l/min ≤ Q) at (0,000500,01+) MPa [(0,00500,1+) bar] Temperature T ≤ 70°C T ≤ 42°C
kSIST FprEN 1113:2014
FprEN 1113:2014 (E) 7
Key 1 cold water 2 hot Water 3 mains supply pipe (Supply pressures up t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.