SIST EN 17361:2023
(Main)Inland navigation vessels - Outboard ladders
Inland navigation vessels - Outboard ladders
This document applies to outboard ladders for inland navigation vessels. Outboard ladders are used on inland navigation vessels having great side heights to facilitate safe climbing into ship's boats, safe disembarking or safe crossing over onto vessels in the case of significantly different boarding heights.
This document specifies safety requirements on design, dimensions and strength and test conditions for outboard ladders.
Outboard ladders are intended for that range where boarding stairs according to EN 1502 are not sufficient in length. This range starts at a boarding height of approximately at 2,8 m above the light water-line.
Boarding ladders are not intended for use by passengers.
Fahrzeuge der Binnenschifffahrt - Außenbordleitern
Dieses Dokument gilt für Außenbordleitern für Fahrzeuge der Binnenschifffahrt. Außenbordleitern werden auf Fahrzeugen der Binnenschifffahrt mit großer Seitenhöhe eingesetzt, um den sicheren Einstieg in Beiboote, den sicheren Übergang zum Land oder das sichere Übersteigen zu benachbarten Schiffen bei sehr unterschiedlichen Bordhöhen zu ermöglichen.
Dieses Dokument legt Sicherheitsanforderungen an Bauart, Maße und Festigkeit sowie Prüfbedingungen für Außenbordleitern fest.
Außenbordleitern sind für den Bereich vorgesehen, in dem Außenbordtreppen nach EN 1502 bezüglich ihrer Länge nicht ausreichen. Dieser Bereich beginnt bei einer Bordhöhe von ungefähr 2,8 m über der Leerwasserlinie.
Außenbordleitern sind nicht für die Benutzung durch Fahrgäste vorgesehen.
Bateaux de navigation intérieure - Échelles de bordé
Le présent document s’applique aux échelles de bordé pour les bateaux de navigation intérieure. Les échelles de bordé sont utilisées sur les bateaux de navigation intérieure avec de grandes hauteurs de muraille pour assurer la sécurité des transferts vers les canots, du débarquement sur la terre ferme ou du passage sur des navires à pont inférieur lorsque les hauteurs pour l’embarquement sont significativement différentes.
Le présent document spécifie les exigences de sécurité relatives à la conception, aux dimensions, à la résistance et aux conditions d’essai pour les échelles de bordé.
Les échelles de bordé sont conçues pour la gamme de bateaux de navigation intérieure pour lesquels les escaliers de bordaille conformes à l’EN 1502 ne sont pas suffisamment longs. Cette gamme démarre à une hauteur de bord de plus d’environ 2,8 m au-dessus de la ligne d’eau à vide.
Les échelles de bordé ne sont pas destinées à être utilisées par les passagers.
Plovila za celinske vode - Zunanje lestve
Ta dokument se uporablja za zunanje lestve za plovila za celinsko plovbo. Zunanje lestve se uporabljajo na plovilih za celinsko plovbo z veliko bočno višino, da se omogoči varen vstop na plovilo, izkrcanje ali varno prestopanje na plovila v primeru zelo različnih višin vkrcanja.
Ta dokument določa varnostne zahteve glede zasnove, dimenzij in trdnosti ter preskusne pogoje za zunanje lestve.
Zunanje lestve so namenjene tistim razponom, kjer stopnice za vkrcanje v skladu s standardom EN 1502 niso dovolj dolge. Ta razpon se začne pri višini vkrcanja približno 2,8 m nad vodno gladino pri lahki teži plovila.
Zunanje lestve niso namenjene potnikom.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 17361:2023
01-april-2023
Plovila za celinske vode - Zunanje lestve
Inland navigation vessels - Outboard ladders
Fahrzeuge der Binnenschifffahrt - Außenbordleitern
Bateaux de navigation intérieure - Échelles de bordé
Ta slovenski standard je istoveten z: EN 17361:2023
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
47.060 Jezerska in rečna plovila Inland navigation vessels
97.145 Lestve Ladders
SIST EN 17361:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 17361:2023
---------------------- Page: 2 ----------------------
SIST EN 17361:2023
EN 17361
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2023
EUROPÄISCHE NORM
ICS 47.020.10; 47.060 Supersedes EN 17361:2020
English Version
Inland navigation vessels - Outboard ladders
Bateaux de navigation intérieure - Échelles de bordé Fahrzeuge der Binnenschifffahrt - Außenbordleitern
This European Standard was approved by CEN on 2 January 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17361:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 17361:2023
EN 17361:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Safety requirements . 5
4.1 Dimensions . 5
4.2 Parts . 5
4.2.1 General . 5
4.2.2 Stringer and handhold . 5
4.2.3 Steps . 5
4.2.4 Spacers . 6
4.2.5 Web. 7
4.3 Holder of the outboard ladder . 7
4.3.1 General . 7
4.3.2 Type A . 7
4.3.3 Type B . 8
4.4 Adjustable hook (H) . 8
4.4.1 Dimensions . 8
4.4.2 Fasteners . 8
4.5 Assembly . 9
4.6 Strength . 10
5 Construction . 10
5.1 Watertightness . 10
5.2 Buoyancy . 10
5.3 Safe tread . 10
5.4 Mass . 10
5.5 Materials . 10
6 Testing . 11
6.1 General . 11
6.2 Test of materials . 11
6.3 Strength test . 11
6.3.1 Outboard ladder . 11
6.3.2 Handhold . 11
6.3.3 Adjustable hook . 11
6.4 Bouyancy test . 11
7 Designation. 11
8 Marking . 12
Bibliography . 13
2
---------------------- Page: 4 ----------------------
SIST EN 17361:2023
EN 17361:2023 (E)
European foreword
This document (EN 17361:2023) has been prepared by Technical Committee CEN/TC 15 “Inland
navigation vessels”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2023, and conflicting national standards shall be
withdrawn at the latest by August 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 17361:2020.
The main changes compared to EN 17361:2020 are listed below:
a) 5.1 has been replaced by the Clause “Watertightness”;
b) 5.4 has been deleted.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 17361:2023
EN 17361:2023 (E)
1 Scope
This document is applicable to outboard ladders for inland navigation vessels. Outboard ladders are used
on inland navigation vessels having great side heights to facilitate safe climbing into ship's boats, safe
disembarking or safe crossing over onto vessels in the case of significantly different boarding heights.
This document specifies safety requirements on design, dimensions and strength and test conditions for
outboard ladders.
...
SLOVENSKI STANDARD
oSIST prEN 17361:2022
01-april-2022
Plovila za celinske vode - Zunanje lestve
Inland navigation vessels - Outboard ladders
Fahrzeuge der Binnenschifffahrt - Außenbordleitern
Bateaux de navigation intérieure - Échelles de bordé
Ta slovenski standard je istoveten z: prEN 17361
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
47.060 Jezerska in rečna plovila Inland navigation vessels
97.145 Lestve Ladders
oSIST prEN 17361:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 17361:2022
---------------------- Page: 2 ----------------------
oSIST prEN 17361:2022
DRAFT
EUROPEAN STANDARD
prEN 17361
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2022
ICS 47.020.10; 47.060 Will supersede EN 17361:2020
English Version
Inland navigation vessels - Outboard ladders
Bateaux de navigation intérieure - Échelles de bordé Fahrzeuge der Binnenschifffahrt - Außenbordleitern
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 15.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17361:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 17361:2022
prEN 17361:2022 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Safety requirements . 5
4.1 Dimensions . 5
4.2 Parts . 5
4.2.1 General . 5
4.2.2 Stringer and handhold . 5
4.2.3 Steps . 5
4.2.4 Spacers . 6
4.2.5 Web. 7
4.3 Holder of the outboard ladder . 7
4.3.1 General . 7
4.3.2 Type A . 7
4.3.3 Type B . 8
4.4 Adjustable hook (H) . 8
4.4.1 Dimensions . 8
4.4.2 Fasteners . 8
4.5 Assembly . 9
4.6 Strength . 10
5 Construction . 10
5.1 Watertightness . 10
5.2 Buoyancy . 10
5.3 Safe tread . 10
5.4 Mass . 10
5.5 Materials . 10
6 Testing . 11
6.1 General . 11
6.2 Test of materials . 11
6.3 Strength test . 11
6.3.1 Outboard ladder . 11
6.3.2 Handhold . 11
6.3.3 Adjustable hook . 11
6.4 Bouyancy test . 11
7 Designation. 11
8 Marking . 12
Bibliography . 13
2
---------------------- Page: 4 ----------------------
oSIST prEN 17361:2022
prEN 17361:2022 (E)
European foreword
This document (prEN 17361:2022) has been prepared by Technical Committee CEN/TC 15 “Inland
navigation vessels”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 17361:2020.
Compared to to EN 17361:2020, the following changes have been made:
a) subclause 5.1 has been replaced by the Clause “Watertightness”;
b) subclause 5.4 has been deleted.
3
---------------------- Page: 5 ----------------------
oSIST prEN 17361:2022
prEN 17361:2022 (E)
1 Scope
This document applies to outboard ladders for inland navigation vessels. Outboard ladders are used on
inland navigation vessels having great side heights to facilitate safe climbing into ship's boats, safe
disembarking or safe crossing over onto vessels in the case of significantly different boarding heights.
This document specifies safety requirements on design, dimensions and strength and test conditions for
outboard ladders.
Outboard ladders are intended for that range where boarding stairs according to EN 1502 are not
sufficient in length. This range starts at a boarding height of approximately at 2,8 m above the light water-
line.
Bo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.