Industrial valves - Check valves of thermoplastics materials (ISO 16137:2006)

This European Standard specifies requirements and tests for check valves of thermoplastics materials with the function to allow the flow of liquid fluids through the valve in one direction only and to prevent backflow.
This standard is applicable to check valves to be installed in industrial pipe systems, irrespective of the field of application and the liquid fluids to be conveyed. For other and/or special applications special requirements may apply.
The range of DN is:
DN 8, DN 10, DN 15, DN 20, DN 25, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150, DN 200, DN 250, DN 300, DN 350, DN 400, DN 500 und DN 600.
The range of PN and Class is:
PN 4, PN 6, PN 10, PN 16, PN 25, Class 150 und Class 300.
The requirements specified by this standard concern the design, functional characteristics and manufacture of diaphragm valves, their connection to the pipe system, the body materials and their pressure/temperature rating between - 40 °C up to + 120 °C, for a lifetime of 25 years.

Industriearmaturen - Rückflussverhinderer aus Thermoplasten (ISO 16137:2006)

Diese Internationale Norm legt die Anforderungen an die Konstruktion, Funktionsmerkmale und die Herstellung von Rückflussverhinderern aus Thermoplasten für flüssige Medien fest, die Durchfluss in einer Richtung zulassen und Rückströmung verhindern, sowie deren Anschluss an das Rohrleitungssystem, Gehäusewerkstoffe und Druck/Temperatur-Zuordnungen zwischen – 40 °C und + 120 °C, für eine Lebensdauer von 25 Jahren. Sie legt auch die entsprechenden Prüfungen fest.
Diese Internationale Norm gilt für Armaturen, die in industrielle Rohrleitungssysteme eingebaut werden, unabhängig vom Einsatzbereich und dem zu befördernden Medium.
ANMERKUNG 1      Industrielle Rohrleitungssysteme umfassen auch Rohrleitungen für Wasserversorgung für allgemeine Zwecke, Entwässerung und Entsorgung.
ANMERKUNG 2      Rohrleitungssysteme für Wasser für den menschlichen Gebrauch können besonderen Anforderungen unterliegen.
Diese Internationale Norm erstreckt sich auf die folgenden DN-Bereiche:
DN 8, DN 10, DN 15, DN 20, DN 25, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150, DN 200, DN 250, DN 300, DN 350, DN 400, DN 500 und DN 600
sowie auf die folgenden PN- und Class-Bereiche:
PN 6, PN 10, PN 16, PN 25, Class 150 und Class 300.

Robinetterie industrielle - Clapets de non-retour en matériaux thermoplastiques (ISO 16137:2006)

La présente norme prescrit les caractéristiques et les essais pour les clapets de non-retour en matériaux plastiques qui ont pour fonction de permettre le débit du fluide liquide a travers l'appareil de robinetterie dans une direction seulement et d'éviter tout refoulement.
La présente norme s'applique aux clapets de non-retour destinés a etre installés dans des systemes de tuyauteries industrielles, indépendamment du domaine d'application et des fluides véhiculés. Pour des applications autres ou spéciales, d'autres spécifications peuvent s'appliquer.
La gamme de DN est :
DN 8 ; DN 10 ; DN 15 ; DN 20 ; DN 25 ; DN 40 ; DN 50 ; DN 65 ; DN 80 ; DN 100 ; DN 125 ; DN 150 ; DN 200 ; DN 250 ; DN 300 ; DN 350 ; DN 400 ; DN 500 et DN 600.
La gamme de PN et de Class est :
PN 4 ; PN 6 ; PN 10 ; PN 16 ; PN 25 ; Class 150 et Class 300.
La présente norme prescrit les caractéristiques concernant la conception, les caractéristiques fonctionnelles et la fabrication des clapets de non-retour, de leur raccordement aux systemes de tuyauteries, les matériaux du corps et leurs relations pression/température dans la gamme - 40 °C a 120 °C, pour une durée de vie standard de 25 ans.

Industrijski ventili - Protipovratni ventili iz plastomernih materialov (ISO 16137:2006)

Ta evropski standard določa zahteve in preskuse za protipovratne ventile iz plastomernih materialov s funkcijo, ki omogoča pretok tekočin skozi ventil samo v eni smeri in preprečuje povratni tok.
Ta standard se uporablja za protipovratne ventile, ki so namenjeni za namestitev v industrijskih cevnih sistemih, ne glede na področje uporabe in tekoče fluide, ki se bodo prenašali. Za druge in/ali posebne uporabe lahko veljajo posebne zahteve.
Obseg vrednosti DN:
DN 8, DN 10, DN 15, DN 20, DN 25, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150, DN 200, DN 250, DN 300, DN 350, DN 400, DN 500, DN 600.
Obseg vrednosti PN in razred:
PN 4, PN 6, PN 10, PN 16, PN 25, razred 150 in razred 300.
Zahteve, ki so določene v tem standardu, obravnavajo projektiranje, funkcionalne karakteristike in proizvodnjo ventilov z opnami, njihovo povezavo s cevnim sistemom, materiale ohišja ter njihovo oceno tlaka/temperature med –40 °C in 120 °C za življenjsko dobo 25 let.

General Information

Status
Published
Publication Date
30-Jun-2006
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jul-2006
Due Date
01-Jul-2006
Completion Date
01-Jul-2006

Relations

Buy Standard

Standard
EN ISO 16137:2006
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2006
Industrijski ventili - Protipovratni ventili iz plastomernih materialov (ISO
16137:2006)
Industrial valves - Check valves of thermoplastics materials (ISO 16137:2006)
Industriearmaturen - Rückflussverhinderer aus Thermoplasten (ISO 16137:2006)
Robinetterie industrielle - Clapets de non-retour en matériaux thermoplastiques (ISO
16137:2006)
Ta slovenski standard je istoveten z: EN ISO 16137:2006
ICS:
23.060.50
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 16137
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2006
ICS 23.060.50
English Version
Industrial valves - Check valves of thermoplastics materials (ISO
16137:2006)
Robinetterie industrielle - Clapets de non-retour en Industriearmaturen - Rückflussverhinderer aus
matériaux thermoplastiques (ISO 16137:2006) Thermoplasten (ISO 16137:2006)
This European Standard was approved by CEN on 3 March 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16137:2006: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 16137:2006) has been prepared by Technical Committee CEN/TC 69
"Industrial valves", the secretariat of which is held by AFNOR, in collaboration with Technical
Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids".

This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2006, and conflicting national
standards shall be withdrawn at the latest by September 2006.

This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

ANNEX ZA
(informative)
Relationship between this International Standard and the Essential
Requirements of EU Directive 97/23 EC (PED)

This International Standard has been prepared under a mandate given to CEN by the European

Commission and the European Free Trade Association to provide one means of conforming to
Essential Requirements of the New Approach Directive 97/23/EC (PED).

Once this standard is cited in the Official Journal of the European Communities under that Directive
and has been implemented as a national standard in at least one Member State, compliance with
the clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this
standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.

Table ZA.1 — Correspondence between this Standard and Directive 97/23/EC (PED)

Sub-clause(s) of this Essential Requirements (ERs) of EU Directive 97/23/EC
International Standard
4.1; 4.3; 5.2 Design for adequate strength 2.2.1
5.2.3 Type test 2.2.2
4.8.1 Wear 2.7
4.7.1 Traceability 3.1.5
8.1 Marking 3.3
4.8.3 Operating instruction 3.4
4.2; 4.3 Materials for pressurized parts 4.1, 4.2 a)
WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.

INTERNATIONAL ISO
STANDARD 16137
First edition
2006-03-15
Industrial valves — Check valves
of thermoplastics materials
Robinetterie industrielle — Clapets de non-retour en matériaux
thermoplastiques
Reference number
ISO 16137:2006(E)
©
ISO 2006
ISO 16137:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved

ISO 16137:2006(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Requirements . 4
4.1 Design . 4
4.2 Materials . 5
4.3 Pressure/temperature rating. 5
4.4 Dimensions. 6
4.5 Operation . 7
4.6 Functional characteristics . 7
4.7 Manufacture. 8
4.8 Other requirements. 8
5 Test procedures . 9
5.1 Documentation of test results . 9
5.2 Initial type tests. 9
6 Declaration of compliance . 10
7 Designation . 10
8 Marking and preparation for storage and transportation. 11
8.1 Marking and documentation. 11
8.2 Preparation for storage and transportation . 12
Annex A (informative) Procurement information . 13
Bibliography . 14

ISO 16137:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16137 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 69, Industrial valves, in collaboration with ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids, Subcommittee SC 7, Valves and auxiliary equipment of plastics materials, in accordance
with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).

iv © ISO 2006 – All rights reserved

INTERNATIONAL STANDARD ISO 16137:2006(E)

Industrial valves — Check valves of thermoplastics materials
1 Scope
This International Standard specifies requirements for the design, functional characteristics and manufacture
of check valves made of thermoplastics materials intended to allow the flow of liquid fluids through the valve in
one direction only and to prevent backflow, their connection to the pipe system, the body materials and their
pressure/temperature rating between − 40 °C and + 120 °C, for a lifetime of 25 years, and also specifies their
tests.
This International Standard is applicable to valves to be installed in industrial pipe systems, irrespective of the
field of application and the fluids to be conveyed.
NOTE 1 Industrial pipe systems also include systems for water supply for general purposes, drainage and sewerage.
NOTE 2 Special requirements can apply to pipe systems for water for human consumption.
This International Standard is concerned with the range of DN
DN 8, DN 10, DN 15, DN 20, DN 25, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150, DN 200,
DN 250, DN 300, DN 350, DN 400, DN 500 and DN 600
and the range of PN and Class
PN 6, PN 10, PN 16, PN 25, and Class 150 and Class 300.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions,
tolerances and designation
ISO 228-1:2000, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions,
tolerances and designation
ISO 898-1:1999, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts,
screws and studs
ISO 8659:1989, Thermoplastic valves — Fatigue strength — Test method
ISO 9393-2:2005, Thermoplastics valves for industrial applications — Pressure test methods and
requirements — Part 2: Test conditions and basic requirements
ISO/TR 10358:1993, Plastics pipes and fittings — Combined chemical-resistance classification table
ISO 10931:2005, Plastics piping systems for industrial applications — Poly(vinylidene fluoride) (PVDF) —
Specifications for components and the system
---
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.