SIST EN ISO 14732:2013
(Main)Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO 14732:2013)
Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO 14732:2013)
This International Standard specifies requirements for qualification of welding operators and also weld setters for mechanized and automatic welding. This International Standard does not apply to personnel exclusively performing loading or unloading of the automatic welding unit. This International Standard is applicable when qualification testing of welding operators and weld setters is required by the contract or by the application standard. The requirements for testing of stud welding operators and setters are given in ISO 14555. The qualification and revalidation is in accordance with this International Standard. Annex A dealing with functional knowledge forms an integral part of this International Standard. Annex B dealing with welding technical knowledge, Annex C outlining the qualification test certificate and the Bibliography are informative.
Schweißpersonal - Prüfung von Bedienern und Einrichtern zum mechanischen und automatischen Schweißen von metallischen Werkstoffen (ISO 14732:2013)
Diese Internationale Norm legt die Anforderungen für die Qualifizierung von Bedienern für das vollmechanische und automatische Schweißen sowie von Einrichtern für das vollmechanische und automatische Schweißen fest. Personen, die ausschließlich die Schweißeinrichtung beim automatischen Schweißen be- und entladen,
benötigen keine besondere Qualifizierung. Diese Internationale Norm ist anzuwenden, wenn eine Prüfung des Bedieners/Einrichters durch den Vertrag
oder durch die Anwendungsnorm verlangt wird. Die Anforderungen zur Prüfung von Bedienern/Einrichtern von Bolzenschweißeinrichtungen sind in ISO 14555
festgelegt. Die Qualifizierung und Revalidierung entspricht dieser Norm.
Personnel en soudage - Épreuve de qualification des opérateurs soudeurs et des régleurs en soudage pour le soudage mécanisé et le soudage automatique des matériaux métalliques (ISO 14732:2013)
L'ISO 14732:2013 spécifie des exigences relatives à la qualification des opérateurs soudeurs et des régleurs en soudage pour le soudage mécanisé et le soudage automatique.
Elle n'est pas applicable au personnel chargé exclusivement du chargement et du déchargement de l'unité de soudage.
L'ISO 14732:2013 est applicable lorsque l'épreuve de qualification des opérateurs soudeurs et des régleurs en soudage est exigée par le contrat ou par la norme d'application.
Varilno osebje - Preskušanje usposobljenosti varilcev za popolnoma mehanizirano talilno in uporovno varjenje kovinskih materialov (ISO 14732:2013)
Ta mednarodni standard določa zahteve za usposobljenost varilcev za popolnoma mehanizirano varjenje. Ta mednarodni standard ne velja za osebje, ki je zadolženo izključno za nalaganje ali odstranjevanje avtomatske varilne enote. Ta mednarodni standard se uporabi, ko pogodba ali standard uporabe zahteva preskušanje usposobljenosti varilcev. Zahteve za preskušanje varilcev čepov so podane v standardu ISO 14555. Usposobljenost in ponovna validacija sta v skladu s tem mednarodnim standardom. Dodatek A vsebuje obrazce za funkcionalna znanja in je sestavni del tega mednarodnega standarda. Dodatek B, ki obravnava tehnično znanje o varjenju, dodatek C, ki vsebuje certifikat o preskusu usposobljenosti, in bibliografija so informativne narave.
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14732:2013
01-oktober-2013
1DGRPHãþD
SIST EN 1418:1999
Varilno osebje - Preskušanje usposobljenosti varilcev za popolnoma mehanizirano
talilno in uporovno varjenje kovinskih materialov (ISO 14732:2013)
Welding personnel - Qualification testing of welding operators and weld setters for
mechanized and automatic welding of metallic materials (ISO 14732:2013)
Schweißpersonal - Prüfung von Bedienern und Einrichtern zum mechanischen und
automatischen Schweißen von metallischen Werkstoffen (ISO 14732:2013)
Personnel en soudage - Épreuve de qualification des opérateurs soudeurs et des
régleurs en soudage pour le soudage mécanisé et le soudage automatique des
matériaux métalliques (ISO 14732:2013)
Ta slovenski standard je istoveten z: EN ISO 14732:2013
ICS:
03.100.30 Vodenje ljudi Management of human
resources
25.160.01 Varjenje, trdo in mehko Welding, brazing and
spajkanje na splošno soldering in general
SIST EN ISO 14732:2013 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14732:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 14732:2013
EUROPEAN STANDARD
EN ISO 14732
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2013
ICS 03.100.30; 25.160.01 Supersedes EN 1418:1997
English Version
Welding personnel - Qualification testing of welding operators
and weld setters for mechanized and automatic welding of
metallic materials (ISO 14732:2013)
Personnel en soudage - Épreuve de qualification des Schweißpersonal - Prüfung von Bedienern und Einrichtern
opérateurs soudeurs et des régleurs en soudage pour le zum mechanischen und automatischen Schweißen von
soudage mécanisé et le soudage automatique des metallischen Werkstoffen (ISO 14732:2013)
matériaux métalliques (ISO 14732:2013)
This European Standard was approved by CEN on 7 March 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14732:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14732:2013
EN ISO 14732:2013 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14732:2013
EN ISO 14732:2013 (E)
Foreword
This document (EN ISO 14732:2013) has been prepared by Technical Committee ISO/TC 44 "Welding and
allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2014, and conflicting national standards shall be withdrawn
at the latest by February 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1418:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14732:2013 has been approved by CEN as EN ISO 14732:2013 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 14732:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 14732:2013
INTERNATIONAL ISO
STANDARD 14732
Second edition
2013-08-01
Welding personnel — Qualification
testing of welding operators and weld
setters for mechanized and automatic
welding of metallic materials
Personnel en soudage — Épreuve de qualification des opérateurs
soudeurs et des régleurs en soudage pour le soudage mécanisé et le
soudage automatique des matériaux métalliques
Reference number
ISO 14732:2013(E)
©
ISO 2013
---------------------- Page: 7 ----------------------
SIST EN ISO 14732:2013
ISO 14732:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 14732:2013
ISO 14732:2013(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Qualification . 3
4.1 Methods of qualification . 3
4.2 Essential variables and the range of qualification . 4
5 Period of validity . 5
5.1 Initial qualification . 5
5.2 Confirmation of validity . 5
5.3 Revalidation of qualification . 5
5.4 Revocation of qualification . 5
6 Certificate . 6
7 Documentation . 6
Annex A (normative) Functional knowledge appropriate to the welding unit .7
Annex B (informative) Knowledge of welding technology . 8
Annex C (informative) Qualification test certificate for welding operators or weld setters .12
Bibliography .14
© ISO 2013 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 14732:2013
ISO 14732:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 44, Welding and allied processes, Subcommittee
SC 11, Qualification requirements for welding and allied processes personnel.
This second edition cancels and replaces the first edition (ISO 14732:1998), of which it constitutes a
technical revision.
Requests for official interpretations of any aspect of this International Standard should be directed to
the Secretariat of ISO/TC 44/SC 11 via your national standards body. A complete listing of these bodies
can be found at www.iso.org.
iv © ISO 2013 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 14732:2013
ISO 14732:2013(E)
Introduction
This International Standard is intended to provide the basis for the mutual recognition by examining
bodies of qualification related to the competence of welding operators and weld setters in the various
fields of application. Tests shall by carried out in accordance with this International Standard unless
more severe tests are specified by the relevant application standard, when these shall be applied.
The welding operator’s or weld setter’s ability and job knowledge continue to be approved only if the
welding operators or weld setters are working with reasonable continuity on welding work within the
extent of qualification. However, a functional knowledge test is mandatory.
It is presumed that the welding operator or weld setter has received training or has industrial practice
within the range of qualification.
All new qualifications are to be in accordance with this International Standard from the date of issue.
At the end of its period of validity, the existing and valid qualification testing of welding operators
and weld setters in accordance with the requirements of a national standard may be revalidated in
accordance with this International Standard. The new range of qualification will be interpreted in
accordance with the requirements of this International Standard.
© ISO 2013 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 14732:2013
---------------------- Page: 12 ----------------------
SIST EN ISO 14732:2013
INTERNATIONAL STANDARD ISO 14732:2013(E)
Welding personnel — Qualification testing of welding
operators and weld setters for mechanized and automatic
welding of metallic materials
1 Scope
This International Standard specifies requirements for qualification of welding operators and also weld
setters for mechanized and automatic welding.
This International Standard does not apply to personnel exclusively performing loading or unloading of
the automatic welding unit.
This International Standard is applicable when qualification testing of welding operators and weld
setters is required by the contract or by the application standard.
The requirements for testing of stud welding operators and setters are given in ISO 14555. The
qualification and revalidation is in accordance with this International Standard.
Annex A dealing with functional knowledge forms an integral part of this International Standard.
Annex B dealing with welding technical knowledge, Annex C outlining the qualification test certificate
and the Bibliography are informative.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references only the edition cited applies. For undated references the latest edition of the referenced
document (including any amendments) applies.
ISO 3834-2, Quality requirements for fusion welding of metallic materials — Part 2: Comprehensive
quality requirements
ISO 3834-3, Quality requirements for fusion welding of metallic materials — Part 3: Standard quality requirements
ISO 4063, Welding and allied processes — Nomenclature of processes and reference numbers
ISO 9606-1, Qualification testing of welders — Fusion welding — Part 1: Steels
ISO 9606-2, Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys
ISO 9606-3, Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys
ISO 9606-4, Approval testing of welders — Fusion welding — Part 4: Nickel and nickel alloys
ISO 9606-5, Approval testing of welders — Fusion welding — Part 5: Titanium and titanium alloys, zirconium
and zirconium alloys
ISO 14555, Welding — Arc stud welding of metallic materials
ISO 15609-1, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 1: Arc welding
ISO 15609-3, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 3: Electron beam welding
ISO 15609-4, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 4: Laser beam welding
© ISO 2013 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 14732:2013
ISO 14732:2013(E)
ISO 15609-5, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 5: Resistance welding
ISO 15613, Specification and qualification of welding procedures for metallic materials — Qualification
based on pre-production welding test
ISO 15614-1, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
ISO 15614-2, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 2: Arc welding of aluminium and its alloys
ISO 15614-5, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 5: Arc welding of titanium, zirconium and their alloys
ISO 15614-6, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 6: Arc and gas welding of copper and its alloys
ISO 15614-7, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 7: Overlay welding
ISO 15614-8, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 8: Welding of tubes to tube-plate joints
ISO 15614-11, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 11: Electron and laser beam welding
ISO 15614-13, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 13: Upset (resistance butt) and flash welding
ISO 15614-14, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 14: Laser-arc hybrid welding of steels, nickel and nickel alloys
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
automatic welding
welding in which all operations are performed without welding operator intervention during the process
Note 1 to entry: Manual adjustment of welding variables by the welding operator during welding is not possible.
3.2
mechanized welding
welding where the required welding conditions are maintained by mechanical or electronic means but
may be manually varied during the process
3.3
pre-production welding test
welding test having the same function as a welding procedure test, but based on a non-
...
SLOVENSKI STANDARD
SIST EN ISO 14732:2013
01-oktober-2013
1DGRPHãþD
SIST EN 1418:1999
Varilno osebje - Preskušanje usposobljenosti varilcev za popolnoma mehanizirano
talilno in uporovno varjenje kovinskih materialov (ISO 14732:2013)
Welding personnel - Qualification testing of welding operators and weld setters for
mechanized and automatic welding of metallic materials (ISO 14732:2013)
Schweißpersonal - Prüfung von Bedienern und Einrichtern zum mechanischen und
automatischen Schweißen von metallischen Werkstoffen (ISO 14732:2013)
Personnel en soudage - Épreuve de qualification des opérateurs soudeurs et des
régleurs en soudage pour le soudage mécanisé et le soudage automatique des
matériaux métalliques (ISO 14732:2013)
Ta slovenski standard je istoveten z: EN ISO 14732:2013
ICS:
03.100.30 Vodenje ljudi Management of human
resources
25.160.01 Varjenje, trdo in mehko Welding, brazing and
spajkanje na splošno soldering in general
SIST EN ISO 14732:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14732:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 14732:2013
EUROPÄISCHE NORM
EN ISO 14732
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2013
ICS 03.100.30; 25.160.01 Ersatz für EN 1418:1997
Deutsche Fassung
Schweißpersonal - Prüfung von Bedienern und Einrichtern zum
mechanischen und automatischen Schweißen von metallischen
Werkstoffen (ISO 14732:2013)
Welding personnel - Qualification testing of welding Personnel en soudage - Épreuve de qualification des
operators and weld setters for mechanized and automatic opérateurs soudeurs et des régleurs en soudage pour le
welding of metallic materials (ISO 14732:2013) soudage mécanisé et le soudage automatique des
matériaux métalliques (ISO 14732:2013)
Diese Europäische Norm wurde vom CEN am 7. März 2013 angenommen.
Die CEN-Mitglieder sind gehalten, die CEN/CENELEC-Geschäftsordnung zu erfüllen, in der die Bedingungen festgelegt sind, unter denen
dieser Europäischen Norm ohne jede Änderung der Status einer nationalen Norm zu geben ist. Auf dem letzten Stand befindliche Listen
dieser nationalen Normen mit ihren bibliographischen Angaben sind beim Management-Zentrum des CEN-CENELEC oder bei jedem CEN-
Mitglied auf Anfrage erhältlich.
Diese Europäische Norm besteht in drei offiziellen Fassungen (Deutsch, Englisch, Französisch). Eine Fassung in einer anderen Sprache,
die von einem CEN-Mitglied in eigener Verantwortung durch Übersetzung in seine Landessprache gemacht und dem Management-
Zentrum mitgeteilt worden ist, hat den gleichen Status wie die offiziellen Fassungen.
CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Bulgarien, Dänemark, Deutschland, der ehemaligen jugoslawischen
Republik Mazedonien, Estland, Finnland, Frankreich, Griechenland, Irland, Island, Italien, Kroatien, Lettland, Litauen, Luxemburg, Malta,
den Niederlanden, Norwegen, Österreich, Polen, Portugal, Rumänien, Schweden, der Schweiz, der Slowakei, Slowenien, Spanien, der
Tschechischen Republik, der Türkei, Ungarn, dem Vereinigten Königreich und Zypern.
EUROPÄISCHES KOMITEE FÜR NORMUNG
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
CEN-CENELEC Management-Zentrum: Avenue Marnix 17, B-1000 Brüssel
© 2013 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Ref. Nr. EN ISO 14732:2013 D
Verfahren, sind weltweit den nationalen Mitgliedern von CEN vorbehalten.
---------------------- Page: 3 ----------------------
SIST EN ISO 14732:2013
EN ISO 14732:2013 (D)
Inhalt
Seite
Vorwort .3
Einleitung .4
1 Anwendungsbereich .5
2 Normative Verweisungen .5
3 Begriffe .6
4 Qualifizierung .7
4.1 Verfahren zur Qualifizierung .7
4.2 Wesentliche Einflussgrößen und Geltungsbereich .8
5 Gültigkeitsdauer.9
5.1 Erstmalige Prüfung .9
5.2 Bestätigung der Gültigkeit .9
5.3 Verlängerung der Qualifikation .9
5.4 Entzug der Qualifikation .9
6 Prüfungsbescheinigung . 10
7 Dokumentation . 10
Anhang A (normativ) Funktionskenntnisse bezogen auf die Schweißeinrichtung . 11
A.1 Allgemeines . 11
A.2 Schweißfolgen/Verfahren bei dem entsprechenden Prozess . 11
A.3 Fugenvorbereitung und Beschreibung des Schweißens bei dem entsprechenden Prozess . 11
A.4 Schweißnaht-Unregelmäßigkeiten bei dem entsprechenden Prozess . 11
A.5 Prüfung des Bedieners oder Einrichters von Schweißeinrichtungen . 11
A.6 Prozessablauf . 11
Anhang B (informativ) Fachkunde über die Technologie beim Schweißen . 12
B.1 Allgemeines . 12
B.2 Anforderungen . 12
Anhang C (informativ) Prüfungsbescheinigung für Bediener oder Einrichter von
Schweißeinrichtungen . 16
Literaturhinweise . 18
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14732:2013
EN ISO 14732:2013 (D)
Vorwort
Dieses Dokument (EN ISO 14732:2013) wurde vom Technischen Komitee ISO/TC 44 „Welding and allied
processes“ in Zusammenarbeit mit dem Technischen Komitee CEN/TC 121 „Schweißen und verwandte
Verfahren“ erarbeitet, dessen Sekretariat vom DIN gehalten wird.
Diese Europäische Norm muss den Status einer nationalen Norm erhalten, entweder durch Veröffentlichung
eines identischen Textes oder durch Anerkennung bis Februar 2014, und etwaige entgegenstehende
nationale Normen müssen bis Februar 2014 zurückgezogen werden.
Es wird auf die Möglichkeit hingewiesen, dass einige Elemente dieses Dokuments Patentrechte berühren
können. CEN [und/oder CENELEC] sind nicht dafür verantwortlich, einige oder alle diesbezüglichen
Patentrechte zu identifizieren.
Dieses Dokument ersetzt EN 1418:1997.
Entsprechend der CEN-CENELEC-Geschäftsordnung sind die nationalen Normungsinstitute der folgenden
Länder gehalten, diese Europäische Norm zu übernehmen: Belgien, Bulgarien, Dänemark, Deutschland, die
ehemalige jugoslawische Republik Mazedonien, Estland, Finnland, Frankreich, Griechenland, Irland, Island,
Italien, Kroatien, Lettland, Litauen, Luxemburg, Malta, Niederlande, Norwegen, Österreich, Polen, Portugal,
Rumänien, Schweden, Schweiz, Slowakei, Slowenien, Spanien, Tschechische Republik, Türkei, Ungarn,
Vereinigtes Königreich und Zypern.
Anerkennungsnotiz
Der Text von ISO 14732:2013 wurde vom CEN als EN ISO 14732:2013 ohne irgendeine Abänderung
genehmigt.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 14732:2013
EN ISO 14732:2013 (D)
Einleitung
Mit dieser Internationalen Norm ist beabsichtigt, die Grundlage für die gegenseitige Qualifizierung von
Prüfungen über das Können der Bediener und Einrichter von Schweißeinrichtungen in den verschiedenen
Anwendungsgebieten durch die Prüfstellen zu schaffen. Die Prüfungen sind in Übereinstimmung mit dieser
Norm durchzuführen, es sei denn, dass gemäß der in Betracht kommenden Anwendungsnorm schwierige
Prüfungen verlangt werden.
Das Können und die Fachkenntnisse des Bedieners oder Einrichters von Schweißeinrichtungen bleiben nur
dann erhalten, wenn dieser regelmäßig Schweißarbeiten innerhalb des Zulassungsbereiches ausführt. Eine
Prüfung der Funktionskenntnisse bezogen auf die Schweißeinrichtung ist hierfür erforderlich.
Es wird vorausgesetzt, dass der Bediener oder Einrichter von Schweißeinrichtungen einen Lehrgang oder ein
Industriepraktikum innerhalb seines Zulassungsbereiches absolviert hat.
Alle neuen Prüfungen müssen vom Tag der Veröffentlichung dieser Internationalen Norm mit ihr
übereinstimmen.
Am Ende der Gültigkeitsdauer darf eine bestehende und gültige Bediener- und Einrichterprüfung, erhalten auf
Basis einer Nationalen Norm, nach dieser Internationalen Norm verlängert werden. Der neue
Gültigkeitsbereich beruht auf den Festlegungen dieser Internationalen Norm.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 14732:2013
EN ISO 14732:2013 (D)
1 Anwendungsbereich
Diese Internationale Norm legt die Anforderungen für die Qualifizierung von Bedienern und Einrichtern für das
mechanische und automatische Schweißen fest.
Diese Internationale Norm gilt nicht für Personen, die ausschließlich die Schweißeinrichtung beim
automatischen Schweißen be- oder entladen.
Diese Internationale Norm ist anzuwenden, wenn eine Prüfung des Bedieners und Einrichters durch den
Vertrag oder durch die Anwendungsnorm verlangt wird.
Die Anforderungen zur Prüfung von Bedienern und Einrichtern von Bolzenschweißeinrichtungen sind in
ISO 14555 festgelegt. Die Qualifizierung und Revalidierung entspricht dieser Internationalen Norm.
Anhang A behandelt die Funktionskenntnisse und ist fester Bestandteil dieser Internationalen Norm. Der
Anhang B behandelt die Fachkundeprüfung und der Anhang C enthält eine Prüfungsbescheinigung. Beide
Anhänge sind wie die Literarturhinweise informativ.
2 Normative Verweisungen
Die folgenden zitierten Dokumente sind für die Anwendung dieses Dokuments erforderlich. Bei datierten
Verweisungen gilt nur die in Bezug genommene Ausgabe. Bei undatierten Verweisungen gilt die letzte
Ausgabe des in Bezug genommenen Dokuments (einschließlich aller Änderungen).
ISO 3834-2, Quality requirements for fusion welding of metallic materials — Part 2: Comprehensive quality
requirements
ISO 3834-3, Quality requirements for fusion welding of metallic materials — Part 3: Standard quality
requirements
ISO 4063, Welding and allied processes — Nomenclature of processes and reference numbers
ISO 9606-1, Qualification testing of welders — Part 1: Steels
ISO 9606-2, Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys
ISO 9606-3, Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys
ISO 9606-4, Approval testing of welders — Fusion welding — Part 4: Nickel and nickel alloys
ISO 9606-5, Approval testing of welders — Fusion welding — Part 5: Titanium and titanium alloys, zirconium
and zirconium alloys
ISO 14555, Welding — Arc stud welding of metallic materials
ISO 15609-1, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 1: Arc welding
ISO 15609-3, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 3: Electron beam welding
ISO 15609-4, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 4: Laser beam welding
ISO 15609-5, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 5: Resistance welding
ISO 15613, Specification and qualification of welding procedures for metallic materials — Qualification based
on pre-production welding test
ISO 15614-1, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
5
---------------------- Page: 7 ----------------------
SIST EN ISO 14732:2013
EN ISO 14732:2013 (D)
ISO 15614-2, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 2: Arc welding of aluminium and its alloys
ISO 15614-5, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 5: Arc welding of titanium, zirconium and their alloys
ISO 15614-6, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 6: Arc and gas welding of copper and its alloys
ISO 15614-7, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 7: Overlay welding
ISO 15614-8, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 8: Welding of tubes to tube-plate joints
ISO 15614-11, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 11: Electron and laser beam welding
ISO 15614-13, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 13: Upset (resistance butt) and flash welding
ISO 15614-14, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 14: Laser-arc hybrid welding of steels, nickel and nickel alloys
3 Begriffe
Für die Anwendung dieses Dokuments gelten die folgenden Begriffe.
3.1
automatisches Schweißen
Schweißen, wobei alle Vorgänge ohne Eingreifen des Bedieners während des Schweißprozesses ablaufen
Anmerkung 1 zum Begriff: Nachstellen schweißtechnischer Einflussgrößen während des Schweißvorganges von Hand
nicht möglich.
3.2
mechanisches Schweißen
Schweißen, bei dem die während des Prozesses erforderlichen variierenden Schweißeinstellungen, auch
manuell, über mechanische oder elektronische Einrichtungen ablaufen
3.3
schweißtechnische Prüfung vor Fertigungsbeginn
Prüfung einer Schweißung, die die gleiche Bedeutung wie eine Schweißverfahrensprüfung hat, jedoch auf
einem nichtgenormten Prüfstück mit nachgeahmten Fertigungsbedingungen beruht
3.4
Fertigungsprüfung
Prüfung, die im Fertigungsbereich an der Schweißeinrichtung, an vorliegenden Teilen in der Fertigung oder an
vereinfachten Prüfstücken ausgeführt werden, wobei die Fertigung während dieser Prüfung unterbrochen wird
3.5
Stichprobenprüfung
Prüfung an vorliegenden schweißtechnischen Erzeugnissen, die beim Einsatz einer Schweißeinrichtung aus
der fortlaufenden Fertigung entnommen werden
3.6
Programmierung
Einbinden der anerkannten Schweißanweisung und/oder der festgelegten Bewegungen der
Schweißeinrichtung in ein Programm
6
---------------------- Page: 8 ----------------------
SIST EN ISO 14732:2013
EN ISO 14732:2013 (D)
3.7
Einrichten
richtiges Einstellen der Schweißeinrichtung vor dem Schweißen und, falls erforderlich, beim Einspeisen des
Roboterprogramms
3.8
Bediener von Schweißeinrichtungen
Person, die beim mechanischen oder automatischen Schweißen die jeweiligen Schweißparameter überwacht
oder anpasst
3.9
Einrichter
Person, die mechanische und automatische Schweißeinrichtungen einrichtet
3.10
Schweißeinrichtung
Schweißanlage, eingerichtet mit geeigneten Geräten wie z. B. Einspann- und Aufspannvorrichtungen,
Roboter, Manipulatoren und Drehvorrichtungen
3.11
Arbeitsweise der Schweißeinrichtung
Starten und, falls notwendig, Stoppen des Fertigungsablaufes, einschließlich Be- und Entladen der
Werkstücke
3.12
Prüfer
qualifizierte Person, die benannt ist, um die Übereinstimmung mit der anzuwendenden Norm zu prüfen
Anmerkung 1 zum Begriff: In bestimmten Fällen kann ein unabhängiger externer Prüfer gefordert werden.
3.13
Prüfstelle
Organisation, die benannt ist, um die Übereinstimmung mit der anzuwendenden Norm zu prüfen
Anmerkung 1 zum Begriff: In bestimmten Fällen kann eine unabhängige externe Prüfstelle gefordert werden.
3.14
Schweißvorrichtung
einzelnes Gerät zur Nutzung beim Schweißen, wie z. B. Stromversorgungseinrichtung oder
Drahtvorschubgerät
4 Qualifizierung
4.1 Verfahren zur Qualifizierung
Die Prüfung von Bedienern und Einrichtern von Schweißeinrichtungen muss nach einer in Übereinstimmung
mit dem entsprechenden Teil der ISO 15609 vorbereiteten vorläufigen Schweißanweisung (pWPS) oder
Schweißanweisung (WPS) erfolgen.
Die Bediener oder Einrichter für Schweißeinrichtungen müssen nach einem der folgenden Verfahren
qualifiziert werden:
a) Qualifizierung auf der Grundlage einer Schweißverfahrensprüfung, nach dem entsprechenden Teil der
ISO 15614;
b) Qualifizierung auf der Grundlage einer schweißtechnischen Prüfung vor Fertigungsb
...
SLOVENSKI STANDARD
oSIST prEN ISO 14732:2011
01-junij-2011
Varilno osebje - Preskušanje usposobljenosti varilcev za popolnoma mehanizirano
talilno in uporovno varjenje kovinskih materialov (ISO/DIS 14732:2011)
Welding personnel - Qualification testing of welding operators for fully mechanized
welding and weld setters for fully mechanized welding and automatic welding of metallic
materials (ISO/DIS 14732:2011)
Schweißpersonal - Prüfung von Bedienern/Einrichtern von Schweißeinrichtungen zum
vollmechanischen und automatischen Schweißen von metallischen Werkstoffen
(ISO/DIS 14732:2011)
Personnel en soudage - Épreuve de qualification des opérateurs soudeurs pour le
soudage totalement mécanisé et des régleurs en soudage pour le soudage totalement
mécanisé et le soudage automatique des matériaux métalliques (ISO/DIS 14732:2011)
Ta slovenski standard je istoveten z: prEN ISO 14732
ICS:
03.100.30 Vodenje ljudi Management of human
resources
25.160.01 Varjenje, trdo in mehko Welding, brazing and
spajkanje na splošno soldering in general
oSIST prEN ISO 14732:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 14732:2011
---------------------- Page: 2 ----------------------
oSIST prEN ISO 14732:2011
EUROPEAN STANDARD
DRAFT
prEN ISO 14732
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 25.160.01 Will supersede EN 1418:1997
English Version
Welding personnel - Qualification testing of welding operators
for fully mechanized welding and weld setters for fully
mechanized welding and automatic welding of metallic materials
(ISO/DIS 14732:2011)
Personnel en soudage - Épreuve de qualification des Schweißpersonal - Prüfung von Bedienern/Einrichtern von
opérateurs soudeurs pour le soudage totalement mécanisé Schweißeinrichtungen zum vollmechanischen und
et des régleurs en soudage pour le soudage totalement automatischen Schweißen von metallischen Werkstoffen
mécanisé et le soudage automatique des matériaux (ISO/DIS 14732:2011)
métalliques (ISO/DIS 14732:2011)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 121.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 14732:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 14732:2011
prEN ISO 14732:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 14732:2011
prEN ISO 14732:2011 (E)
Foreword
This document (prEN ISO 14732:2011) has been prepared by Technical Committee ISO/TC 44 "Welding and
allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is
held by DIN.
This document is currently submitted to the parallel Enquiry.
This document will supersede EN 1418:1997.
Endorsement notice
The text of ISO/DIS 14732:2011 has been approved by CEN as a prEN ISO 14732:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 14732:2011
---------------------- Page: 6 ----------------------
oSIST prEN ISO 14732:2011
DRAFT INTERNATIONAL STANDARD ISO/DIS 14732
ISO/TC 44/SC 11 Secretariat: SUTN
Voting begins on Voting terminates on
2011-03-24 2011-08-24
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Welding personnel — Qualification testing of welding operators
for fully mechanized welding and weld setters for fully
mechanized welding and automatic welding of metallic
materials
Personnel en soudage — Épreuve de qualification des opérateurs soudeurs pour le soudage totalement
mécanisé et des régleurs en soudage pour le soudage totalement mécanisé et le soudage automatique des
matériaux métalliques
[Revision of first edition (ISO 14732:1998)]
ICS 25.160.01
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME
STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2011
---------------------- Page: 7 ----------------------
oSIST prEN ISO 14732:2011
ISO/DIS 14732
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 14732:2011
ISO 14732:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 14732 was prepared by Technical Committee ISO/TC 44, Welding and allied
processes, Subcommittee SC 11, Qualification requirements for welding and allied processes personnel.
Annex A forms an integral part of this International Standard, annexes B to D are for information only.
© ISO 2011 – All right reserved 3
DRAFT 2011
---------------------- Page: 9 ----------------------
oSIST prEN ISO 14732:2011
ISO 14732:2011(E)
Introduction
This International Standard is intended to provide the basis for the mutual recognition by examining bodies for
qualification related to the competence of welding operators and weld setters in the various fields of application.
Tests shall by carried out in accordance with this International Standard unless more severe test are specified by
the relevant application standard when these shall be applied.
The welding operator's/weld setter's ability and job knowledge continue to be approved only if the welding
operators/ weld setters are working with reasonable continuity on welding work within the extent of qualification.
However a functional knowledge test is mandatory.
It is presumed that the welding operator or weld setter has received training and/or has industrial practice within the
range of qualification.
All new qualifications are to be in accordance with this International Standard from the date of issue.
At the end of its period of validity, the existing and valid qualification testing of welding operator's/weld setter’s in
accordance with the requirement of a national standard may be revalidated according to this International standard.
The new range of qualification will be interpreted in accordance with the requirements of this International
standard.
4 © ISO 2011 – All right reserved
DRAFT 2011
---------------------- Page: 10 ----------------------
oSIST prEN ISO 14732:2011
INTERNATIONAL STANDARD © ISO
ISO 14732:2011(E)
ISO 14732:2011(E)
Welding personnel — Qualification testing of welding operators
for fully mechanized welding and weld setters for fully
mechanized welding and automatic welding of metallic
materials
1 Scope
This International Standard specifies requirements for qualification of welding operators for fully mechanized
welding and also weld setters for fully mechanized and automatic welding.
Personnel exclusively performing loading or unloading of the automatic welding unit do not need any qualification.
This International Standard is applicable when qualification testing of operators/welding equipment setters is
required by the contract or by the application standard.
The requirements for testing of stud welding operators/setters are given in ISO 14555. The qualification and
revalidation is in accordance with this standard.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
ISO 857-1:1998, Welding and allied processes — Vocabulary — Part 1: Metal welding processes.
ISO 15609-1:2004, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 1: Arc welding.
ISO 15614-1:2004, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys.
ISO 15614-2:2005, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 2: Arc welding of aluminium and its alloys.
ISO 15613:2004, Specification and qualification of welding procedures for metallic materials — Qualification based
on pre-production welding test.
ISO 15609-3:2004, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 3: Electron beam welding.
ISO 15609-4:2009, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 4: Laser beam welding.
ISO 10447:2006, Resistance welding — Peel and chisel testing of resistance spot and projection welds.
ISO 14731:2006, Welding coordination — Tasks and responsibilities.
© ISO 2011 – All right reserved 5
DRAFT 2011
---------------------- Page: 11 ----------------------
oSIST prEN ISO 14732:2011
ISO 14732:2011(E)
ISO 14555:2006, Welding — Arc stud welding of metallic materials.
ISO 3834-2:2005, Quality requirements for fusion welding of metallic materials — Part 2: Comprehensive quality
requirements.
ISO 3834-3:2005, Quality requirements for fusion welding of metallic materials — Part 3: Standard quality
requirements.
ISO 15614-7:2007, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 7: Overlay welding.
ISO 15614-11:2002, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 11: Electron and laser beam welding.
ISO 15614-12:2004, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 12: Spot, seam and projection welding.
1)
ISO 9606-1:— , Qualification testing of welders — Part 1: Steels.
ISO 9606-2:2004, Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys.
ISO 9606-3:1999, Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys.
ISO 9606-4:1999, Approval testing of welders — Fusion welding — Part 4: Nickel and nickel alloys.
ISO 9606-5:2000, Approval testing of welders — Fusion welding — Part 5: Titanium and titanium alloys, zirconium
and zirconium alloys.
3 Terms and definitions
For the purpose of this International Standard, the following terms and definitions apply.
3.1 automatic welding:
Welding in which all operations are mechanized.
NOTE Adjustment of the welding variables by the welding operator during welding is not possible.
[ISO/TR 25901]
3.2 function test:
Test of a welding unit set-up in accordance with a Welding Procedure Specification (WPS).
[ISO/TR 25901]
3.3 fully mechanized welding:
Welding in which all operations (excluding the handling of the work piece) are mechanized.
NOTE Adjustment of the welding variables by the welding operator during welding is possible.
[ISO/TR 25901]
3.4 pre-production welding test:
Welding test having the same function as a welding procedure test, but based on a non-standard test piece,
simulating production conditions.
1) To be published. (Revision of ISO 9606-1:1994)
6 © ISO 2011 – All right reserved
DRAFT 2011
---------------------- Page: 12 ----------------------
oSIST prEN ISO 14732:2011
ISO 14732:2011(E)
3.5 production test:
Welding test carried out in the production environment with the welding unit on actual products or test pieces
before production or during an interruption in production.
[ISO/TR 25901]
3.6 production sample testing:
Sample testing of actual welding products sampled from a continuous production using the welding unit, no
interruption of normal production during sampling being necessary.
3.7 programming:
Incorporation of the approved welding procedure specification and/or the specified movements of the welding unit
into a programme.
3.8 setting-up:
Correct adjustment of the welding unit before welding, if required by entering the robot programme.
3.9 welding operator:
A person who performs fully mechanized or automatic welding.
3.10 weld setter:
A person who sets up welding equipments for fully mechanized or automatic welding.
[ISO/TR 25901]
3.11 welding unit:
Welding plant completed with appropriate apparatus e.g. jigs and fixtures, robot(s) manipulators and rotating
devices
[ISO/TR 25901]
3.12 welding unit operation:
The starting and, if necessary, the stopping of the production cycle including loading and unloading the work
pieces.
[ISO/TR 25901]
3.13 examiner:
A person who has been appointed to verify compliance with the applicable standard.
NOTE In certain cases, an external independent examiner can be required.
[ISO/TR 25901]
3.14 examining body:
organization that has been appointed to verify compliance with the applicable standard.
NOTE In certain cases, an external independent examiner can be required.
[ISO/TR 25901]
3.15 welding equipment:
Individual apparatus used in weldi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.