SIST EN ISO 15528:2020
(Main)Paints, varnishes and raw materials for paints and varnishes - Sampling (ISO 15528:2020)
Paints, varnishes and raw materials for paints and varnishes - Sampling (ISO 15528:2020)
This document specifies procedures for the sampling of paints and varnishes, including coating
powders, and raw materials used in their manufacture. Such products include liquids and materials
which, without undergoing chemical modification, are capable of being liquefied when heated up, and
powdered, granulated and pasty materials. Samples can be taken from containers, for example cans,
drums, tanks, tank wagons or ships' tanks, as well as from barrels, sacks, big-bags, silos or silo wagons
or conveyor belts.
This document does not deal with the sample preparation for testing or reduction of the samples thus
taken, which is dealt with in ISO 1513.
Beschichtungsstoffe und Rohstoffe für Beschichtungsstoffe - Probenahme (ISO 15528:2020)
Dieses Dokument legt Verfahren zur Probenahme von Beschichtungsstoffen einschließlich Pulverlacken und Rohstoffen, die zu ihrer Herstellung verwendet werden, fest. Eingeschlossen sind Flüssigkeiten und solche Produkte, die sich beim Erhitzen verflüssigen, ohne sich chemisch zu verändern, sowie pulverisierte, granulierte und pastenförmige Produkte. Proben können aus Behältern, z. B. Dosen, Trommeln, Tanks, Kesselwagen oder Schiffskammern sowie Fässern, Säcken, Big Bags, Silos oder Silofahrzeugen oder von Förderbändern genommen werden.
Dieses Dokument behandelt nicht die Probenvorbereitung und Einengung von auf diese Weise erhaltenen Proben, die in ISO 1513 behandelt werden.
Peintures, vernis et matières premières pour peintures et vernis - Échantillonnage (ISO 15528:2020)
Le présent document spécifie des modes opératoires pour l'échantillonnage des peintures et des vernis, y compris des poudres pour revêtement, et des matières premières pour peintures, vernis et poudres pour revêtement utilisés dans leur fabrication. Ces produits comprennent les produits liquides et les produits qui, sans subir de modification chimique, peuvent se liquéfier lorsqu'ils sont chauffés, ainsi que les produits sous forme de poudre, de granulés ou de pâte. Les échantillons peuvent être prélevés dans des récipients comme par exemple des bidons, des fûts, des réservoirs, des wagons-citernes ou des réservoirs de navire, ainsi que dans des tonneaux, des sacs, des grands sacs, des silos ou des wagons silos, ou sur des bandes transporteuses.
Le présent document ne traite pas de la préparation des échantillons pour essais ou de la réduction des échantillons ainsi prélevés, qui est traitée dans l'ISO 1513.
Barve, laki ter surovine za barve in lake - Vzorčenje (ISO 15528:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15528:2020
01-november-2020
Nadomešča:
SIST EN ISO 15528:2014
Barve, laki ter surovine za barve in lake - Vzorčenje (ISO 15528:2020)
Paints, varnishes and raw materials for paints and varnishes - Sampling (ISO
15528:2020)
Beschichtungsstoffe und Rohstoffe für Beschichtungsstoffe - Probenahme (ISO
15528:2020)
Peintures, vernis et matières premières pour peintures et vernis - Échantillonnage (ISO
15528:2020)
Ta slovenski standard je istoveten z: EN ISO 15528:2020
ICS:
87.040 Barve in laki Paints and varnishes
87.060.01 Sestavine barv na splošno Paint ingredients in general
SIST EN ISO 15528:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15528:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 15528:2020
EN ISO 15528
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 15528:2013
English Version
Paints, varnishes and raw materials for paints and
varnishes - Sampling (ISO 15528:2020)
Peintures, vernis et matières premières pour peintures Beschichtungsstoffe und Rohstoffe für
et vernis - Échantillonnage (ISO 15528:2020) Beschichtungsstoffe - Probenahme (ISO 15528:2020)
This European Standard was approved by CEN on 31 July 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15528:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15528:2020
EN ISO 15528:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15528:2020
EN ISO 15528:2020 (E)
European foreword
This document (EN ISO 15528:2020) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15528:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15528:2020 has been approved by CEN as EN ISO 15528:2020 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15528:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 15528:2020
INTERNATIONAL ISO
STANDARD 15528
Third edition
2020-05
Paints, varnishes and raw materials
for paints and varnishes — Sampling
Peintures, vernis et matières premières pour peintures et vernis —
Échantillonnage
Reference number
ISO 15528:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 15528:2020
ISO 15528:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 15528:2020
ISO 15528:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Sampling equipment . 3
5.1 Sampling devices . 3
5.1.1 General. 3
5.1.2 Scoops . 3
5.1.3 Sampling tubes for liquids . 5
5.1.4 Sampling bottle or can . 8
5.1.5 Bottom or zone sampler . 9
5.1.6 Spatula .10
5.1.7 Shovel .10
5.1.8 Branch pipe.10
5.2 Sample containers .10
6 Sampling procedure .11
6.1 General .11
6.2 Pre-sampling inspection .11
6.3 Taking samples from containers .11
6.3.1 Number of samples and homogeneity .11
6.3.2 Liquids .11
6.3.3 Products in paste form . .11
6.3.4 Solids .11
6.4 Reduction in sample size .11
6.5 Labelling .12
6.6 Storage .12
6.7 Sampling report .12
Bibliography .13
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 15528:2020
ISO 15528:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 15528:2013) and ISO 8130-9:1992, which
have been technically revised. The main changes compared to the previous edition are as follows:
— sampling of powder coatings from ISO 8130-9 has been included in the scope;
— all information on sample dividing of coating powders originally in ISO 8130-9 has been deleted;
— the text has been editorially revised and the normative references have been updated.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 15528:2020
ISO 15528:2020(E)
Introduction
Sampling depends on the product and the size of the container but not on the type of product, for
example paint, varnish, coating powder, binder, pigment, extender or solvent. ISO 1513 specifies both
the procedure for preliminary examination of a single sample as received for testing and the procedure
for preparing a test sample by blending and reduction of a series of samples representative of a
consignment of paint, varnish or related product. The samples of the product to be tested have been
taken in accordance with this document.
Correct sampling forms the basis for the subsequent tests and their results. The various sampling
procedures need to be carried out with great care by operators having the required knowledge and
experience. The general instructions in this document are intended to supplement this knowledge
and experience and are applicable to most situations. However, some products might require special
sampling precautions that are not given in this document; therefore, special vigilance will be necessary
on the part of operators to take note of any unusual characteristics exhibited by those products.
Operators should be aware of product specifications and national safety regulations which could
require special precautions.
© ISO 2020 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 15528:2020
---------------------- Page: 12 ----------------------
SIST EN ISO 15528:2020
INTERNATIONAL STANDARD ISO 15528:2020(E)
Paints, varnishes and raw materials for paints and
varnishes — Sampling
1 Scope
This document specifies procedures for the sampling of paints and varnishes, including coating
powders, and raw materials used in their manufacture
...
SLOVENSKI STANDARD
oSIST prEN ISO 15528:2019
01-oktober-2019
Barve, laki ter surovine za barve in lake - Vzorčenje (ISO/DIS 15528:2019)
Paints, varnishes and raw materials for paints and varnishes - Sampling (ISO/DIS
15528:2019)
Beschichtungsstoffe und Rohstoffe für Beschichtungsstoffe - Probenahme (ISO/DIS
15528:2019)
Peintures, vernis et matières premières pour peintures et vernis - Échantillonnage
(ISO/DIS 15528:2019)
Ta slovenski standard je istoveten z: prEN ISO 15528 rev
ICS:
87.040 Barve in laki Paints and varnishes
87.060.01 Sestavine barv na splošno Paint ingredients in general
oSIST prEN ISO 15528:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 15528:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 15528:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 15528
ISO/TC 35/SC 9 Secretariat: BSI
Voting begins on: Voting terminates on:
2019-09-09 2019-12-02
Paints, varnishes and raw materials for paints and
varnishes — Sampling
Peintures, vernis et matières premières pour peintures et vernis — Échantillonnage
ICS: 87.040
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 15528:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 15528:2019
ISO/DIS 15528:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 15528:2019
ISO/DIS 15528:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Sampling equipment . 3
5.1 Sampling devices . 3
5.1.1 General. 3
5.1.2 Scoops . 3
5.1.3 Sampling tubes for liquids . 5
5.1.4 Sampling bottle or can . 8
5.1.5 Bottom or zone sampler . 9
5.1.6 Spatula .10
5.1.7 Shovel (see also 5.1.2.1) .10
5.1.8 Branch pipe.10
5.2 Sample containers .10
6 Sampling procedure .11
6.1 General .11
6.2 Pre-sampling inspection .11
6.3 Taking samples from containers .11
6.3.1 Number of samples and homogeneity .11
6.3.2 Liquids .11
6.3.3 Products in paste form . .11
6.3.4 Solids .11
6.4 Reduction in sample size .11
6.5 Labelling .12
6.6 Storage .12
6.7 Sampling report .12
Bibliography .13
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 15528:2019
ISO/DIS 15528:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes.
This third edition cancels and replaces the second edition (ISO 15528:2013) and ISO 8130-9:1992, which
have been technically revised. The main changes compared to the previous editions are as follows:
— Sampling of powder coatings from ISO 8130-9 has been included in the scope of ISO 15528;
— All information on sample deviding of coating powders originally in ISO 8130-9 has been deleted;
— The text has been editorially revised and the normative references have been updated.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 15528:2019
ISO/DIS 15528:2019(E)
Introduction
Sampling depends on the product and the size of the container but not on the type of product, e.g. paint,
varnish, coating powder, binder, pigment, extender or solvent. ISO 1513 specifies both the procedure
for preliminary examination of a single sample as received for testing, and the procedure for preparing
a test sample by blending and reduction of a series of samples representative of a consignment of paint,
varnish or related product. The samples of the product to be tested have been taken in accordance with
this document.
Correct sampling forms the basis for the subsequent tests and their results. The various sampling
procedures need to be carried out with great care by operators having the required knowledge and
experience. The general instructions in this document are intended to supplement this knowledge
and experience and are applicable to most situations. However, some products might require special
sampling precautions that are not given in this document; therefore, special vigilance will be necessary
on the part of operators to take note of any unusual characteristics exhibited by those products. It is also
essential that operators adhere to any special precautions in accordance with product specifications
and national safety regulations.
© ISO 2019 – All rights reserved v
---------------------- Page: 7 ----------------------
oSIST prEN ISO 15528:2019
---------------------- Page: 8 ----------------------
oSIST prEN ISO 15528:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 15528:2019(E)
Paints, varnishes and raw materials for paints and
varnishes — Sampling
1 Scope
This document specifies procedures for the sampling of paints, varnishes, including coating powders,
and raw materials used in their manufacture. Such products include liquids and materials which,
without undergoing chemical modification, are capable of being liquefied when heated up, and
powdered, granulated and pasty materials. Samples may be taken from containers, e.g. cans, drums,
tanks, tank wagons or ships' tanks, as well as from barrels, sacks, big-bags, silos or silo wagons, or from
conveyor belts.
This document does not deal with the sample preparation for testing or reduction of the samples thus
taken. This is dealt with in ISO 1513.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 4618, Paints and varnishes — Terms and definitions
ISO 6206, Chemical products for industrial use — Sampling — Vocabulary
3 Terms and definitions
For the purposes of this document, the following terms and definitions given in ISO 4618, ISO 6206 and
the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
batch
definite quantity of a material which was produced under uniform conditions
3.2
lot
total quantity of material which is to be sampled
Note 1 to entry: The lot can consist of a number of bat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.