SIST-TS CEN/TS 19100-2:2022
(Main)Design of glass structures - Part 2: Design of out-of-plane loaded glass components
Design of glass structures - Part 2: Design of out-of-plane loaded glass components
1.1 Scope of FprCEN/TS 19100 2
(1) FprCEN/TS 19100 2 gives basic structural design rules for mechanically supported glass components primarily subjected to out of plane loading. Out of plane loaded glass components are made of flat or curved glass components.
NOTE Out of plane loads are loads acting normal (e.g wind) to or having a component (e.g dead load, snow, ...) acting normal to the glass plane.
1.2 Assumptions
(1) The assumptions of EN 1990 apply to FprCEN/TS 19100-2.
(2) This document is intended to be used in conjunction with EN 1990, EN 1991 (all parts), EN 1993-1-1, EN 1995 1 1, EN 1998 1, EN 1999 1 1 and EN 12488.
Bemessung und Konstruktion von Tragwerken aus Glas - Teil 2: Querbelastete Bauteile
0.1 Anwendungsbereich von CEN/TS 19100 2
(1) CEN/TS 19100 2 enthält Bemessungsregeln für mechanisch gelagerte, hauptsächlich querbelastete Glaskomponenten. Querbelastete Glaskomponenten werden aus ebenen oder gekrümmten Glaskomponenten hergestellt.
ANMERKUNG Querlasten sind Lasten (z. B. Wind) mit senkrechter Einwirkung oder mit einer Komponente (z. B. Eigengewicht, Schnee, …) mit senkrechter Einwirkung auf die Glasscheibenebene.
0.2 Annahmen
(1) Die Annahmen nach EN 1990 gelten für CEN/TS 19100 2.
(2) Dieses Dokument ist für die Anwendung in Zusammenhang mit EN 1990, EN 1991 (alle Teile), EN 1993 1 1, EN 1995 1 1, EN 1998 1, EN 1999 1 1 und EN 12488 vorgesehen.
Conception et calcul des structures en verre - Partie 2 : Calcul des composants en verre chargés perpendiculairement
1.1 Domaine d’application de la FprCEN/TS 19100 2
(1) La FprCEN/TS 19100 2 énonce les règles de calcul de base des structures dotées de composants en verre maintenus mécaniquement, principalement soumis à une charge perpendiculaire à leur plan. Les composants en verre chargés hors plan sont constitués de composants en verre plat ou bombé.
NOTE Les charges perpendiculaires sont des charges agissant suivant une direction normale (par exemple, le vent) sur le vitrage ou ayant un composant (par exemple, le poids propre, la neige…) agissant normalement sur le vitrage.
1.2 Hypothèses
(1) Les hypothèses énoncées dans l’EN 1990 s’appliquent à la FprCEN/TS 19100-2.
(2) Le présent document est destiné à être utilisé conjointement avec l’EN 1990, l’EN 1991 (toutes les parties), l’EN 1993-1-1, l’EN 1995 1 1, l’EN 1998 1, l’EN 1999 1 1 et l’EN 12488.
Projektiranje steklenih konstrukcij - 2. del: Projektiranje steklenih elementov pod vplivom obtežb izven ravnine elementov
1.1 Področje uporabe FprCEN/TS 19100 2
(1) FprCEN/TS 19100 2 podaja osnovna pravila strukturnega projektiranja za mehansko podprte steklene elemente, ki so izpostavljeni predvsem obtežbam izven ravnine elementov. Stekleni elementi pod vplivom obtežb izven ravnine elementov so izdelani iz ravnih ali ukrivljenih steklenih elementov.
OPOMBA: Obtežbe izven ravnine so obtežbe, ki delujejo normalno (npr. veter) na stekleno ravnino ali imajo element (npr. mrtva obtežba, sneg ...), ki deluje normalno na ravnino stekla.
1.2 Predpostavke
(1) Predpostavke standarda EN 1990 veljajo tudi za FprCEN/TS 19100-2.
(2) Ta dokument je namenjen za uporabo skupaj s standardi EN 1990, EN 1991 (vsi deli), EN 1993-1-1, EN 1995 1 1, EN 1998 1, EN 1999 1 1 in EN 12488.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 19100-2:2022
01-februar-2022
Projektiranje steklenih konstrukcij - 2. del: Projektiranje steklenih elementov pod
vplivom obtežb izven ravnine elementov
Design of glass structures - Part 2: Design of out-of-plane loaded glass components
Bemessung und Konstruktion von Tragwerken aus Glas - Teil 2: Querbelastete Bauteile
Conception et calcul des structures en verre - Partie 2 : Calcul des composants en verre
chargés perpendiculairement
Ta slovenski standard je istoveten z: CEN/TS 19100-2:2021
ICS:
91.080.99 Druge konstrukcije Other structures
SIST-TS CEN/TS 19100-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 19100-2:2022
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 19100-2:2022
CEN/TS 19100-2
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
November 2021
TECHNISCHE SPEZIFIKATION
ICS 91.080.99
English Version
Design of glass structures - Part 2: Design of out-of-plane
loaded glass components
Conception et calcul des structures en verre - Partie 2 : Bemessung und Konstruktion von Tragwerken aus
Calcul des composants en verre chargés Glas - Teil 2: Querbelastete Bauteile
perpendiculairement
This Technical Specification (CEN/TS) was approved by CEN on 25 July 2021 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 19100-2:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 19100-2:2022
CEN/TS 19100-2:2021 (E)
Contents Page
European foreword . 3
0 Introduction . 4
1 Scope . 6
1.1 Scope of CEN/TS 19100-2 6
1.2 Assumptions 6
2 Normative references . 6
3 Terms, definitions and symbols . 6
3.1 Terms and definitions 6
3.2 Symbols and abbreviations 7
4 Basis of design . 8
4.1 Requirements 8
4.2 Fracture Limit State (FLS) verification 8
4.3 Post Fracture Limit State (PFLS) verification 9
5 Materials . 11
6 Durability . 11
7 Structural analysis . 11
8 Ultimate Limit States . 11
9 Serviceability Limit States . 11
10 Joint
...
SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 19100-2:2021
01-junij-2021
Projektiranje steklenih konstrukcij - 2. del: Projektiranje steklenih komponent pod
vplivom sil, ki delujejo navpično na ravnino elementov
Design of glass structures - Part 2: Design of out-of-plane loaded glass components
Bemessung und Konstruktion von Tragwerken aus Glas - Teil 2: Querbelastete Bauteile
Conception et calcul des structures en verre - Partie 2 : Calcul des composants en verre
chargés perpendiculairement
Ta slovenski standard je istoveten z: FprCEN/TS 19100-2
ICS:
91.080.99 Druge konstrukcije Other structures
kSIST-TS FprCEN/TS 19100-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 19100-2:2021
---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 19100-2:2021
FINAL DRAFT
TECHNICAL SPECIFICATION
FprCEN/TS 19100-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
April 2021
ICS 91.080.99
English Version
Design of glass structures - Part 2: Design of out-of-plane
loaded glass components
Conception et calcul des structures en verre - Partie 2 : Bemessung und Konstruktion von Tragwerken aus
Calcul des composants en verre chargés Glas - Teil 2: Querbelastete Bauteile
perpendiculairement
This draft Technical Specification is submitted to CEN members for Vote. It has been drawn up by the Technical Committee
CEN/TC 250.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change
without notice and shall not be referred to as a Technical Specification.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 19100-2:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 19100-2:2021
FprCEN/TS 19100-2:2021 (E)
Contents Page
European foreword . 3
0 Introduction . 4
1 Scope . 7
1.1 Scope of FprCEN/TS 19100-2 . 7
1.2 Assumptions . 7
2 Normative references . 7
3 Terms, definitions and symbols . 7
3.1 Terms and definitions . 7
3.2 Symbols and abbreviations . 8
4 Basis of design . 9
4.1 Requirements . 9
4.2 Fracture Limit State (FLS) verification . 9
4.3 Post Fracture Limit State (PFLS) verification . 10
5 Materials .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.