SIST EN IEC 63203-402-1:2023

SLOVENSKI STANDARD
SIST EN IEC 63203-402-1:2023
01-februar-2023
Nosljive elektronske naprave in tehnologije - 402-1. del: Merjenje zmogljivosti
nosljivih izdelkov za fitnes - Preskusne metode senzorjev gibanja v rokavicah za
merjenje premikov prstov (IEC 63203-402-1:2022)
Wearable electronic devices and technologies - Part 402-1: Performance measurement
of fitness wearables - Test methods of glove-type motion sensors for measuring finger
movements (IEC 63203-402-1:2022)
Tragbare elektronische Geräte und Technologien - Teil 402-1: Performance Messung
von Fitness Wearables - Prüfverfahren für handschuhartige Bewegungssensoren zur
Messung von Fingerbewegungen (IEC 63203-402-1:2022)
Technologies et dispositifs électroniques prêts-à-porter - Partie 402-1: Mesure des
performances des dispositifs prêts-à-porter d’activité physique - Méthodes d’essai des
capteurs de mouvement type gant pour le mesurage des mouvements digitaux (IEC
63203-402-1:2022)
Ta slovenski standard je istoveten z: EN IEC 63203-402-1:2022
ICS:
31.080.99 Drugi polprevodniški elementi Other semiconductor devices
59.080.80 Inteligentne tekstilije Smart textiles
97.220.01 Športna oprema in Sports equipment and
pripomočki na splošno facilities in general
SIST EN IEC 63203-402-1:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 63203-402-1:2023

---------------------- Page: 2 ----------------------
SIST EN IEC 63203-402-1:2023


EUROPEAN STANDARD EN IEC 63203-402-1

NORME EUROPÉENNE

EUROPÄISCHE NORM December 2022
ICS 31.020

English Version
Wearable electronic devices and technologies - Part 402-1:
Performance measurement of fitness wearables - Test methods
of glove-type motion sensors for measuring finger movements
(IEC 63203-402-1:2022)
Technologies et dispositifs électroniques prêts-à-porter - Tragbare elektronische Geräte und Technologien - Teil 402-
Partie 402-1: Mesure des performances des dispositifs 1: Performance Messung von Fitness Wearables -
prêts-à-porter d'activité physique - Méthodes d'essai des Prüfverfahren für handschuhartige Bewegungssensoren zur
capteurs de mouvement type gant pour le mesurage des Messung von Fingerbewegungen
mouvements digitaux (IEC 63203-402-1:2022)
(IEC 63203-402-1:2022)
This European Standard was approved by CENELEC on 2022-12-09. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 63203-402-1:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 63203-402-1:2023
EN IEC 63203-402-1:2022 (E)
European foreword
The text of document 124/195/FDIS, future edition 1 of IEC 63203-402-1, prepared by IEC/TC 124
"Wearable electronic devices and technologies" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 63203-402-1:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-09-09
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-12-09
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 63203-402-1:2022 was approved by CENELEC as a
European Standard without any modification.
2

---------------------- Page: 4 ----------------------
SIST EN IEC 63203-402-1:2023
EN IEC 63203-402-1:2022 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 62047-6 - Semiconductor devices - Micro- EN 62047-6 -
electromechanical devices - Part 6: Axial
fatigue testing methods of thin film
materials
IEC 62951-1 - Semiconductor devices - Flexible and - -
stretchable semiconductor devices - Part 1:
Bending test method for conductive thin
films on flexible substrates
ISO 291 - Plastics - Standard atmospheres for EN ISO 291 -
conditioning and testing
ISO 21420 2020 Protective gloves - General requirements EN ISO 21420 2020
and test methods

3

---------------------- Page: 5 ----------------------
SIST EN IEC 63203-402-1:2023

---------------------- Page: 6 ----------------------
SIST EN IEC 63203-402-1:2023




IEC 63203-402-1

®


Edition 1.0 2022-11




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE
colour

inside










Wearable electronic devices and technologies –

Part 402-1: Performance measurement of fitness wearables – Test methods of

glove-type motion sensors for measuring finger movements



Technologies et dispositifs électroniques prêts-à-porter –

Partie 402-1: Mesure des performances des dispositifs prêts-à-porter d’activité


physique – Méthodes d’essai des capteurs de mouvement type gant pour le

mesurage des mouvements digitaux












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 31.020 ISBN 978-2-8322-5999-3




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 63203-402-1:2023
– 2 – IEC 63203-402-1:2022 © IEC 2022
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
3.1 General terms . 5
3.2 Angle between finger joints . 6
4 Test conditions and method . 7
4.1 Test conditions . 7
4.2 Preparation of gloves under test . 7
4.3 Test methods . 7
4.3.1 Direct measurement test procedure: angle between finger joints. 7
4.3.2 Indirect measurement test procedure: angle between finger joints with
sensors. 9
5 Test report . 11
Annex A (informative) Glove-type motion sensors . 13
A.1 Glove-type motion sensors . 13
A.2 Examples by sensing type . 13
A.2.1 Schematic of a resistive-type glove sensor . 13
A.2.2 Schematic of a capacitive-type glove sensor . 14
A.2.3 Schematic of a piezoelectric-type glove sensor . 14
Bibliography . 15

Figure 1 – Position of DIP, PIP, IP and MCP . 7
Figure 2 – Direct measurement method using a manual goniometer . 8
Figure 3 – Test setup based on the servomotor for sensor angle measurement . 10
Figure 4 – Test procedure of angle measurement in the wearable glove based on the
servomotor. 10
Figure A.1 – Examples of glove-type motion sensors . 13
Figure A.2 – Schematic of a resistive-type glove sensor . 13
Figure A.3 – Schematic of a capacitive-type glove sensor . 14
Figure A.4 – Structure of a piezoelectric-type glove sensor . 14

Table 1 – Comparison of angle data measured with a glove sensor and goniometer . 9
Table 2 – Comparison of angle data measured with a glove sensor and servomotor . 11

---------------------- Page: 8 ----------------------
SIST EN IEC 63203-402-1:2023
IEC 63203-402-1:2022 © IEC 2022 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

WEARABLE ELECTRONIC DEVICES AND TECHNOLOGIES –

Part 402-1: Performance measurement of fitness wearables – Test
methods of glove-type motion sensors for measuring finger movements

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 63203-402-1 has been prepared by IEC technical committee 124: Wearable electronic
devices and technologies. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
124/195/FDIS 124/204/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.

---------------------- Page: 9 ----------------------
SIST EN IEC 63203-402-1:2023
– 4 – IEC 63203-402-1:2022 © IEC 2022
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 63203 series, published under the general title Wearable electronic
devices and technologies, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore
...