SIST EN ISO 8437-2:2021/A1:2026

SLOVENSKI STANDARD
01-julij-2026
Snežne freze - Varnostne zahteve in preskusni postopki - 2. del: Ročno upravljane
snežne freze - Dopolnilo A1 (ISO 8437-1:2019/Amd 1:2026)
Snow throwers - Safety requirements and test procedures - Part 2: Pedestrian-controlled
snow throwers - Amendment 1 (ISO 8437-1:2019/Amd 1:2026)
Schneefräsen - Sicherheitsanforderungen und Prüfverfahren - Teil 2: Handgeführte
Schneefräsen - Änderung 1 (ISO 8437-1:2019/Amd 1:2026)
Chasse-neige - Exigences de sécurité et essais - Partie 2: Chasse-neige à conducteur à
pied - Amendement 1 (ISO 8437-1:2019/Amd 1:2026)
Ta slovenski standard je istoveten z: EN ISO 8437-2:2021/A1:2026
ICS:
43.160 Vozila za posebne namene Special purpose vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 8437-2:2021/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2026
EUROPÄISCHE NORM
ICS 43.160
English Version
Snow throwers - Safety requirements and test procedures
- Part 2: Pedestrian-controlled snow throwers -
Amendment 1 (ISO 8437-2:2019/Amd 1:2026)
Chasse-neige - Exigences de sécurité et essais - Partie Schneefräsen - Sicherheitsanforderungen und
2: Chasse-neige à conducteur à pied - Amendement 1 Prüfverfahren - Teil 2: Handgeführte Schneefräsen -
(ISO 8437-1:2019/Amd 1:2026) Änderung 1 (ISO 8437-1:2019/Amd 1:2026)
This amendment A1 modifies the European Standard EN ISO 8437-2:2021; it was approved by CEN on 21 April 2026.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8437-2:2021/A1:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive2006/42/EC aimed to be covered . 4

European foreword
This document (EN ISO 8437-2:2021/A1:2026) has been prepared by Technical Committee ISO/TC 23
"Tractors and machinery for agriculture and forestry" in collaboration with Technical Committee
CEN/TC 144 “Tractors and machinery for agriculture and forestry” the secretariat of which is held by
AFNOR.
This Amendment to the European Standard EN ISO 8437-2:2021 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by November 2026,
and conflicting national standards shall be withdrawn at the latest by November 2026.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 8437-2:2019/Amd 1:2026 has been approved by CEN as EN ISO 8437-2:2021/A1:2026
without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
The relevant Essential Clause(s)/sub-clause(s) of this Remarks/Notes
Requirements of Directive EN
2006/42/EC
1. ESSENTIAL HEALTH AND
SAFETY REQUIREMENTS
1.1.2. Principles of safety
integration
1.1.2(a) 4, 5
1.1.2(c) 4, 5, annex A
1.1.2(d) (if relevant) 5, A.2.3
1.1.2(e) (if relevant) 5, A.2.6
1.1.3. Materials and products 4.3, 4.4, 4.5, 5
1.1.5. Design of machinery to 4.2, 4.3, 4.4, 4.5, 5
facilitate its handling
1.1.6. Ergonomics 4.2, 5
1.1.7. Operating positions 4.2, 4.3.3, 5
1.2. CONTROL SYSTEMS
1.2.1. Safety and reliability of 4.2, 5
control systems
1.2.2. Control devices 4.2, 5
1.2.3. Starting 4.2.2.1, 5
1.2.4.1. Normal stop 4.2.2.2, 5
1.2.6. Failure of the power 4.2.2.1, 4.2.2.4, 4.2.3.1, 5
supply
The relevant Essential Clause(s)/sub-clause(s) of this Remarks/Notes
Requirements of Directive EN
2006/42/EC
1.3. PROTECTION AGAINST
MECHANICAL HAZARDS
1.3.2. Risk of break-up during 4.2, 4.3, 5
operation
1.3.3. Risks due to falling or 4.3.1
ejected objects
1.3.4. Risks due to surfaces, 4.1, 4.3.1, 4.3.2
edges or angles
1.3.6. Risks related to variations 4.2.2.3, 4.3.4, 5
in operating conditions
1.3.7. Risks related to moving 4.2.3, 4.3, 5
parts
1.3.8.1. Moving transmission 4.2.3, 4.3, 4.6
parts
1.3.8.2. Moving parts involved in 4.2.3, 4.3, 4.6
the process
1.3.9. Risks of uncontrolled 4.2.2.4, 4.2.3.2, 4.2.4.1, 5
movements
1.4. REQUIRED
CHARACTERISTICS OF GUARDS
AND PROTECTIVE DEVICES
1.4.1. General requirements 4.2, 4.3
1.4.2.1. Fixed guards 4.3, 4.6, A.2.4 h
1.4.2.3. Adjustable guards 4.3
restricting access
1.4.3. Special requirements for 4.3, 4.7.2
protective devices
1.5. RISKS DUE TO OTHER
HAZARDS
1.5.1. Electricity supply 4.5
1.5.3. Energy supply other than 4.4
electricity
1.5.5. Extreme temperatures 4.3
1.5.6. Fire 4.4, 4.5
1.5.7. Explosion 4.4, 4.5
1.5.8. Noise 4.9
1.5.9. Vibrations 4.10
1.5.10. Radiation 4.8
The relevant Essential Clause(s)/sub-clause(s) of this Remarks/Notes
Requirements of Directive EN
2006/42/EC
1.5.11. External r
...