SIST EN ISO 25239-2:2020

SLOVENSKI STANDARD
oSIST prEN ISO 25239-2:2019
01-julij-2019
Varjenje z gnetenjem - Aluminij - 2. del: Zasnova zvarnih spojev (ISO/DIS 25239-
2:2019)
Friction stir welding - Aluminium - Part 2: Design of weld joints (ISO/DIS 25239-2:2019)
Rührreibschweißen - Aluminium - Teil 2: Ausführung der Schweißverbindungen (ISO/DIS
25239-2:2019)
Soudage par friction-malaxage - Aluminium - Partie 2: Conception des assemblages
soudés (ISO/DIS 25239-2:2019)
Ta slovenski standard je istoveten z: prEN ISO 25239-2
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
oSIST prEN ISO 25239-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 25239-2:2019

---------------------- Page: 2 ----------------------
oSIST prEN ISO 25239-2:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 25239-2
IIW Secretariat: ISO secretariat
Voting begins on: Voting terminates on:
2019-05-22 2019-08-14
Friction stir welding — Aluminium —
Part 2:
Design of weld joints
Soudage par friction-malaxage — Aluminium —
Partie 2: Conception des assemblages soudés
ICS: 25.160.40; 25.160.10
Member bodies are requested to consult relevant national interests in ISO/TC
44/SC 10 before casting their ballot to the e-Balloting application.
This document is circulated as received from the committee secretariat.
ISO/CEN PARALLEL PROCESSING
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
This draft International Standard is submitted to all ISO member bodies for
NOT BE REFERRED TO AS AN INTERNATIONAL
voting, as a standard prepared by an international standardizing body in
STANDARD UNTIL PUBLISHED AS SUCH.
accordance with Council Resolution 42/1999. The proposer, the International
IN ADDITION TO THEIR EVALUATION AS
Institute of Welding (IIW), has been recognized by the ISO Council as an
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
international standardizing body for the purpose of Council Resolution
USER PURPOSES, DRAFT INTERNATIONAL
42/1999.
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 25239-2:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 25239-2:2019
ISO/DIS 25239-2:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 25239-2:2019
ISO/DIS 25239-2:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Design requirements . 1
4.1 Documentation . 1
4.2 Joint design . 2
4.2.1 Butt joints . 2
4.2.2 Lap joints . 2
4.3 Additional information . 4
4.3.1 Essential information. 4
4.3.2 Weldment dimensions . 4
4.3.3 Welding operator qualification. 4
4.3.4 Welding procedure qualification. 4
4.3.5 Inspection . 4
Bibliography . 5
© ISO 2019 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 25239-2:2019
ISO/DIS 25239-2:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by IIW, International Institute of Welding, Commission III, Resistance
Welding, Solid State Welding and Allied Joining Process.
This second edition cancels and replaces the first edition (ISO 25239-2:2011), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— to be entered closer to publication.
A list of all parts in the ISO 25239- series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found a
...