Wheelchair seating — Part 1: Vocabulary, reference axis convention and measures for body segments, posture and postural support surfaces

ISO 16840-1:2006 applies to seating intended to provide postural support within a wheelchair. It specifies: a global coordinate system that permits the determination and recording of a person's posture while seated in a wheelchair; the standard terms and definitions for use in describing both the posture and the anthropometrics of a person seated in a wheelchair; the terms and definitions for describing the dimensions, location and orientation of seating support surfaces, which together comprise the body support system. ISO 16840-1:2006 does not specify any methods for use in measuring a person's seated posture, nor does it define terms for dynamic physiological movements (such as flexion or extension). ISO 16840-1:2006 might be applicable to seating other than that intended to be used within a wheelchair.

Sièges de fauteuils roulants — Partie 1: Vocabulaire, convention des axes de référence et mesures des segments corporels, des surfaces de posture et du siège

General Information

Status
Published
Publication Date
29-Mar-2006
Current Stage
9060 - Close of review
Start Date
02-Sep-2029
Ref Project

Buy Standard

Standard
ISO 16840-1:2006 - Wheelchair seating
English language
77 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 16840-1
First edition
2006-03-15

Wheelchair seating —
Part 1:
Vocabulary, reference axis convention
and measures for body segments,
posture and postural support surfaces
Sièges de fauteuils roulants —
Partie 1: Vocabulaire, convention des axes de référence et mesures
des segments corporels, des surfaces de posture et du siège




Reference number
ISO 16840-1:2006(E)
©
ISO 2006

---------------------- Page: 1 ----------------------
ISO 16840-1:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2006
The reproduction of the terms and definitions contained in this International Standard is permitted in teaching manuals, instruction
booklets, technical publications and journals for strictly educational or implementation purposes. The conditions for such reproduction are:
that no modifications are made to the terms and definitions; that such reproduction is not permitted for dictionaries or similar publications
offered for sale; and that this International Standard is referenced as the source document.
With the sole exceptions noted above, no other part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2006 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16840-1:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 General terms and definitions . 1
3 Abbreviated terms and subscripts. 6
3.1 Abbreviated terms . 6
3.2 Subscripts . 6
4 Global coordinate system principles. 7
4.1 General. 7
4.2 Structure . 7
5 Terms and definitions of an integrated geometric reference system . 7
5.1 General. 7
5.2 Global coordinate system. 8
5.3 Wheelchair axis system (WAS) . 9
5.4 Support surface axis system (SSAS). 10
5.5 Seated anatomical axis system (SAAS) . 11
6 Terms and definitions
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.