IEC 61394:2011/COR1:2012
(Corrigendum)Corrigendum 1 - Overhead lines - Requirements for greases for aluminium, aluminium alloy and steel bare conductors
Corrigendum 1 - Overhead lines - Requirements for greases for aluminium, aluminium alloy and steel bare conductors
General Information
Relations
Standards Content (Sample)
IEC 61394
(First edition – 2011)
Overhead lines –
Requirements for greases for aluminium,
aluminium alloy and steel bare conductors
CO RRI G E NDUM 1
Table 1 – Classification of tests
Replace the existing Table with the following new Table:
Table 1 – Classification of tests
Type tests Sample tests
Test
Type A Type B Type A Type B
Drop
...
This May Also Interest You
IEC 61394:2011 specifies the requirements and tests of greases designed for corrosion protection of bare overhead conductors.
- Standard18 pagesEnglish languagesale 15% off
IEC 61394:2011 specifies the requirements and tests of greases designed for corrosion protection of bare overhead conductors.
- Standard18 pagesEnglish languagesale 15% off
Gives conditions, categories and frequency of tests, routine tests, special tests, type tests and tests after installation. This consolidated version consists of the fifth edition (1997) and its amendment 1 (2005). Therefore, no need to order amendment in addition to this publication.
- Standard57 pagesEnglish and French languagesale 15% off
- Standard7 pagesEnglish and French languagesale 15% off
IEC 63267-2-1:2024 defines a set of specified conditions for an enhanced macro bend of 50/125 µm, graded index multimode fibre optic connection that is maintained in order to satisfy the requirements of attenuation and return loss performance in a randomly mated pair of polished physically contacting (PC) fibres.
An encircled flux (EF) compliant launch condition in accordance with IEC 61300-1, at an operational wavelength of 850 nm, is used for determination of performance grades, based on lateral fibre core offset, numerical aperture (NA) mismatch, and fibre core diameter (CD) variation.
Fibre core angular offset is considered insignificant given the state-of-the-art and is excluded as a factor for attenuation estimation. Attenuation and return loss performance grades are defined in IEC 63267-1.
- Standard64 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 60335-2-124:2024 deals with the safety of dry ice blasting machines intended for commercial indoor or outdoor use for the hand-guided cleaning, decoating and stripping of surfaces. The blasting machines are either equipped with containers for storage of dry ice or produce dry ice internally. These machines are not equipped with a traction drive.
The following power systems are covered:
- mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances,
- battery-operated machines.
This standard does not apply to
- dry ice blasting machines with integrated generation of compressed air;
- dry ice blasting machines using other transport gases besides compressed air or nitrogen;
- dry ice blasting machines with nozzles being controlled by robotic arms;
- spray extraction machines for commercial use (IEC 60335-2-68);
- high pressure cleaners (IEC 60335-2-79);
- sand blasting equipment (abrasive blasting);
- hand-held and transportable motor-operated electric tools (IEC 60745 series, IEC 61029 series, IEC 62841 series);
- machines designed for use in corrosive or explosive environments (dust, vapour or gas);
- machines designed for use in vehicles in non-ventilated environment;
- machines designed for use on board of ships or aircraft.
- Standard66 pagesEnglish and French languagesale 15% off
IEC TS 61934:2024 is available as IEC TS 61934:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC TS 61934:2024 is applicable to the off-line electrical measurement of partial discharges (PDs) that occur in electrical insulation systems (EISs) when stressed by repetitive voltage impulses generated from power electronics devices.
Typical applications are EISs belonging to apparatus driven by power electronics, such as motors, inductive reactors, wind turbine generators and the power electronics modules themselves.
NOTE Use of this document with specific products can require the application of additional procedures.
Excluded from the scope of this document are:
- methods based on optical or ultrasonic PD detection,
- fields of application for PD measurements when stressed by non-repetitive impulse voltages such as lightning impulse or switching impulses from switchgear.
This edition includes the following significant technical changes with respect to the previous edition:
a) background information on the progress being made in the field of power electronics including the introduction of wide band gap semiconductor devices has been added to the Introduction;
b) voltage impulse generators; the parameter values of the voltage impulse waveform have been modified to reflect application of wide band gap semiconductor devices.
c) PD detection methods; charge-based measurements are not described in this third edition nor are source-controlled gating techniques to suppress external noise.
d) Since the previous edition in 2011, there have been significant technical advances in this field as evidenced by several hundreds of publications. Consequently, the Bibliography in the 2011 edition has been deleted in this third edition.
- Technical specification27 pagesEnglish languagesale 15% off
IEC 61360-7:2024 specifies the new data dictionary (domain) "IEC 61360-7 - General items" including its generic concepts. The IEC 61360-7 data dictionary provides concepts (dictionary elements, e.g. classes, properties) intended for cross-domain use.
This document has the status of a horizontal publication in accordance with IEC Guide 108.
The IEC 61360-7 data dictionary is published in IEC CDD and is available at https://cdd.iec.ch.
- Standard11 pagesEnglish languagesale 15% off
ISO/IEC 14543-5-194:2024(E) specifies the remote access (RA) server-based application framework, device interaction model, flow process and interfaces, and message formats to achieve intelligent grouping, resource sharing and service collaboration among IGRS smart lock devices.
This document is applicable to smart lock devices with direct network connections or connections through an intermediary network to a server for security authentication. This server utilizes a method to minimize the possibility of unauthorized access to these smart locks, while maintaining seamless interoperability among users, smart lock devices and RA servers at home, office or other remote environments.
- Standard28 pagesEnglish languagesale 15% off
- 16-Jan-2024
- 35.240.67
- ISO/IEC JTC 1/SC 25
- Standard4 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.