Amendment 1 - Basic principles for graphical symbols for use on equipment - Part 3: Guidelines for the application of graphical symbols

Amendement 1 - Principes élémentaires pour les symboles graphiques utilisables sur le matériel - Partie 3: Guide pour l'application des symboles graphiques

General Information

Status
Published
Publication Date
11-Jul-2011
Current Stage
PPUB - Publication issued
Start Date
31-Aug-2011
Completion Date
12-Jul-2011
Ref Project

Relations

Buy Standard

Standard
IEC 80416-3:2002/AMD1:2011 - Amendment 1 - Basic principles for graphical symbols for use on equipment - Part 3: Guidelines for the application of graphical symbols
English and French language
12 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC 80416-3
Edition 1.0 2011-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 1
AMENDEMENT 1
Basic principles for graphical symbols for use on equipment –
Part 3: Guidelines for the application of graphical symbols

Principes élémentaires pour les symboles graphiques utilisables sur le matériel –
Partie 3: Guide pour l’application des symboles graphiques

IEC 80416-3:2002/A1:2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
 Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
 IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
 Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
 Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
 Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
 Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
 Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
 Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 80416-3
Edition 1.0 2011-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 1
AMENDEMENT 1
Basic principles for graphical symbols for use on equipment –
Part 3: Guidelines for the application of graphical symbols

Principes élémentaires pour les symboles graphiques utilisables sur le matériel –
Partie 3: Guide pour l’application des symboles graphiques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
F
CODE PRIX
ICS 01.080.20 ISBN 978-2-88912-579-1

– 2 – 80416-3 Amend. 1  IEC:2011
FOREWORD
This amendment has been prepared by subcommittee 3C: Graphical symbols for use on
equipment, of IEC technical committee 3: Information structures, documentation and graphical
symbols.
This amendment has been prepared in collaboration with ISO TC 145/SC 3.
The text of this amendment is based on the following documents:
CDV Report on voting
3C/1687/CDV 3C/1711/RVC
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
INTRODUCTION
Replace the first and the second paragraphs by the following paragraphs, respectively:
A graphical symbol is defined as a visually perceptible figure with a particular meaning used
to transmit information independently of language. Graphical symbols are used on equipment
for a wide range of purposes. The understanding of such symbols can be improved by
consistent design. This is particularly important where families of symbols are used in one
location or on similar equipment. Good design also helps to maintain the legibility of symbols
when they are reduced to small dimensions for application. Thus, there is a need to
standardize the principles for creating graphical symbols for use on equipment to ensure
visual clarity, to maintain consistency and thereby to improve recognition.
The IEC 80416 series is a multi-part international standard which provides basic principles
and guidelines for the creation of graphical symbols for use on equipment (Parts 1 and 2) and
also principles and guidelines for adapting registered graphical symbols for use in practice
(Parts 3 and 4).
1 Scope
Delete the first paragraph.
80416-3 Amend. 1  IEC:2011 – 3 –
2 Normative references
Replace the reference to IEC 80416-1 by the following:
IEC 80416-1:2008, Basic principles for graphical symbols for use on equipment – Part 1:
Creation of graphical symbols for registration
Replace the reference to ISO/FDIS 3864-1:2001 by the following:
ISO 3864-1, Graphical symbols – Safety colours and safety signs – Part 1: Design principles
for safety signs and safety markings
Add the following reference:
ISO 3864-2, Graphical symbols – Safety colours and safety signs – Part 2: Design principles
for product safety labels
Replace the reference to ISO/FDIS 7010:2001 by the following:
ISO 7010, Graphical symbols – Safety colours and safety signs – Safety signs used in
workplaces and public areas
Add the following footnote to ISO 7000:
The ISO 7000 collection of graphical symbols for use on equipment is also available online,
either separately or jointly with the IEC 60417 collection of graphical symbols for use on
equipment. ISO Catalogue provides further information on this regard.
Replace the reference to IEC 60417 (all parts) by the following:
IEC 60417, Graphical symbols for use on equipment
Add the following reference:
ISO 80416-4, Basic principles for graphical symbols for use on equipment – Part 4:
Guidelines for the adaptation of graphical symbols for use on screens and displays (icons)
3 Definitions
Replace the title of Clause 3 by the following:
Terms and definitions
Delete 3.2.
4.2 Screens and displays
Add the following to the first paragraph:
In this application, ISO 80416-4 shall be taken into consideration.
Delete Note 1 and renumber Note 2 to “Note”.

– 4 – 80416-3 Amend. 1  IEC:2011
4.4 International Standards
Replace in Note, the reference ISO/FDIS 14617 by the following:
ISO 14617.
6.1 Modification according to design
Replace the text of the existing subclause by the following:
To coordinate with the design requirements of equipment, it is allowed:
a) to change the line width;
b) to round the corners;
c) to fill areas;
d) to interrupt crossing lines;
e) to adapt distances between graphical elements;
f) to adapt the relative proportions of graphical elements;
g) to modify the type of arrow.
If several graphical symbols are applied together, it can be necessary and it is permitted to
adjust their relative sizes and positions in order to achieve a balanced appearance on the
equipment.
These changes shall only be made to the extent that the basic communicative characteristics
of the graphical symbol remain unchanged.
6.5 Interruption of crossing lines
Add after the existing subclause 6.5, the following new subclause 6.6 and the following new
Figure:
6.6 Modification of arrow type
The arrow type may be modified as in the examples given in Figure 11.

(a) IEC 60417-5964 (b) IEC 60417-5964 (c) IEC 60417-5964
(2005-06): applied with closed arrow appl
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.