IEC 62433-1:2019/COR1:2020
(Corrigendum)Corrigendum 1 - EMC IC modelling - Part 1: General modelling framework
Corrigendum 1 - EMC IC modelling - Part 1: General modelling framework
General Information
Relations
Standards Content (Sample)
IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
IEC 62433-1
Edition 1.0 2019-03
EMC IC MODELLING –
Part 1: General modelling framework
CO
...
This May Also Interest You
IEC TR 62433-4-1:2025 provides an overview of good practices to extract an ICIM-CI model from measurements and to build a numerical model of the PCB in which the ICIM-CI model is used to predict RF immunity of an IC in its application PCB.
This document also discusses factors which can be considered to obtain proper results in an ICIM-CI model extraction and use of the actual model at the PCB level.
- Technical report40 pagesEnglish languagesale 15% off
- Standard5 pagesEnglish and French languagesale 15% off
IEC 61967-8:2023 defines a method for measuring the electromagnetic radiated emission from an integrated circuit (IC) using an IC stripline. The IC being evaluated is mounted on an EMC test board (PCB) between the active conductor and the ground plane of the IC stripline arrangement. This edition includes the following significant technical changes with respect to the previous edition:
a) frequency range of 150 kHz to 3 GHz was deleted from the scope;
b) extension of upper usable frequency to 6 GHz or higher as long as the defined requirements are fulfilled.
- Standard52 pagesEnglish languagesale 15% off
- Standard34 pagesEnglish and French languagesale 15% off
IEC 62228-6:2022 specifies test and measurement methods for EMC evaluation of peripheral sensor interface 5 (PSI5) transceiver integrated circuits (ICs) under network condition. It defines test configurations, test conditions, test signals, failure criteria, test procedures, test setups and test boards. It is applicable for PSI5 satellite ICs (e.g. sensors) and ICs with embedded PSI5 transceivers (e.g. PSI5 electronic control unit IC). The document covers
the emission of RF disturbances,
the immunity against RF disturbances,
the immunity against impulses, and
the immunity against electrostatic discharges (ESD).
- Standard99 pagesEnglish and French languagesale 15% off
IEC 62228-7:2022 specifies test and measurement methods for the EMC evaluation of CXPI transceiver ICs under network condition. It defines test configurations, test conditions, test signals, failure criteria, test procedures, test setups and test boards. This specification is applicable for standard CXPI transceiver ICs and ICs with embedded CXPI transceiver and covers
the emission of RF disturbances,
the immunity against RF disturbances,
the immunity against impulses and
the immunity against electrostatic discharges (ESD).
- Standard101 pagesEnglish and French languagesale 15% off
IEC 62228-5:2021 specifies test and measurement methods for EMC evaluation of Ethernet transceiver ICs under network condition. It defines test configurations, test conditions, test signals, failure criteria, test procedures, test setups and test boards. It is applicable for transceiver of the Ethernet systems
100BASE-T1 according to ISO/IEC/IEEE 8802-3/AMD1;
100BASE-TX according to ISO/IEC/IEEE 8802-3;
1000BASE-T1 according to ISO/IEC/IEEE 8802-3/AMD4
and covers
the emission of RF disturbances;
the immunity against RF disturbances;
the immunity against impulses;
the immunity against electrostatic discharges (ESD).
- Standard108 pagesEnglish languagesale 15% off
- Standard223 pagesEnglish and French languagesale 15% off
IEC 61967-4:2021 specifies a method to measure the conducted electromagnetic emission (EME) of integrated circuits by direct radio frequency (RF) current measurement with a 1 Ω resistive probe and RF voltage measurement using a 150 Ω coupling network. These methods ensure a high degree of reproducibility and correlation of EME measurement results. This edition includes the following significant technical changes with respect to the previous edition:
- frequency range of 150 kHz to 1 GHz has been deleted from the title;
- recommended frequency range for 1 Ω method has been reduced to 30 MHz;
- Annex G with recommendations and guidelines for frequency range extension beyond 1 GHz has been added.
- Standard133 pagesEnglish languagesale 15% off
- Standard88 pagesEnglish and French languagesale 15% off
IEC 62433-6:2020 describes the extraction flow for deriving an immunity macro-model of an Integrated Circuit (IC) against conducted Electrostatic Discharge (ESD) according to IEC 61000-4-2 and Electrical Fast Transients (EFT) according to IEC 61000-4-4.
The model addresses physical damages due to overvoltage, thermal damage and other failure modes. Functional failures can also be addressed. This model allows the immunity simulation of the IC in an application. This model is commonly called "Integrated Circuit Immunity Model Conducted Pulse Immunity", ICIM-CPI.
This document provides:
- the description of ICIM-CPI macro-model elements representing electrical, thermal or logical behaviour of the IC.
- a universal data exchange format based on XML.
- Standard110 pagesEnglish and French languagesale 15% off
IEC 62228-3:2019 specifies test and measurement methods for EMC evaluation of CAN transceiver ICs under network condition. It defines test configurations, test conditions, test signals, failure criteria, test procedures, test setups and test boards. It is applicable for CAN standard transceivers, CAN transceivers with partial networking functionality and CAN transceivers with flexible data rate capability and covers
- the emission of RF disturbances,
- the immunity against RF disturbances,
- the immunity against impulses, and
- the immunity against electrostatic discharges (ESD).
This first edition cancels and replaces the first edition of IEC TS 62228 published in 2007 and constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC TS 62228:
a) introduction of CAN transceivers with partial networking functionality and CAN transceivers with flexible data rate capability and addition of operation modes and test descriptions in the respective subclauses of the document;
b) introduction of minimal communication network with two CAN transceivers;
c) update of the test requirements and targets in Annex C;
d) addition of Annex D for common mode choke characterization.
The contents of the corrigendum of June 2023 have been included in this copy.
- Standard156 pagesEnglish and French languagesale 15% off
IEC 62433-1:2019 specifies the framework and methodology for EMC IC macro-modelling. Terms that are commonly used in IEC 62433 (all parts), different modelling approaches, requirements and data-exchange format for each model category that is standardized in this series are defined in this document.
IEC 62433-1 cancels and replaces IEC TS 62433-1 published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC TS 62433 1:2011:
Incorporation of a data exchange format for an integrated circuit’s model representation.
The contents of the corrigendum of July 2020 have been included in this copy.
- Standard59 pagesEnglish languagesale 15% off
- Standard122 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...