EN 60512-27-100:2012

SLOVENSKI STANDARD
01-maj-2012
Konektorji za elektronsko opremo - Preskusi in meritve - 27-100. del: Preskušanje
neokrnjenosti signalov do 500 MHz na konektorjih serije IEC 60603-7 - Preskusi od
27a do 27g
Connectors for electronic equipment - Tests and measurements - Part 27-100: Signal
integrity tests up to 500 MHz on IEC 60603-7 series connectors - Tests 27a to 27g
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 27-100:
Signalintegritätsprüfungen bis 500 MHz an Steckverbindern der Reihe IEC 60603-7 -
Prüfungen 27a bis 27g
Connecteurs pour équipements électroniques - Essais et mesures - Partie 27-100:
Essais d'intégrité des signaux jusqu'à 500 MHz sur les connecteurs de la série CEI
60603-7 - Essais 27a à 27g
Ta slovenski standard je istoveten z: EN 60512-27-100:2012
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60512-27-100
NORME EUROPÉENNE
February 2012
EUROPÄISCHE NORM
ICS 31.220.10
English version
Connectors for electronic equipment -
Tests and measurements -
Part 27-100: Signal integrity tests up to 500 MHz on IEC 60603-7 series
connectors -
Tests 27a to 27g
(IEC 60512-27-100:2011)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Essais et mesures - Mess- und Prüfverfahren -
Partie 27-100: Essais d'intégrité des Teil 27-100: Signalintegritätsprüfungen bis
signaux jusqu'à 500 MHz sur les 500 MHz an Steckverbindern der Reihe
connecteurs de la série CEI 60603-7 - IEC 60603-7 -
Essais 27a à 27g Prüfungen 27a bis 27g
(CEI 60512-27-100:2011) (IEC 60512-27-100:2011)

This European Standard was approved by CENELEC on 2012-01-11. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-27-100:2012 E

Foreword
The text of document 48B/2262/FDIS, future edition 1 of IEC 60512-27-100, prepared by SC 48B,
"Connectors", of IEC TC 48, "Electromechanical components and mechanical structures for electronic
equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2012-10-11
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-01-11

standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 60512-27-100:2011 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60603-7-4 NOTE  Harmonized as EN 60603-7-4.
IEC 60603-7-5 NOTE  Harmonized as EN 60603-7-5.

- 3 - EN 60512-27-100:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60050-581 - International Electrotechnical Vocabulary - - -
Part 581: Electromechanical components for
electronic equipment
IEC 60512-1 - Connectors for electronic equipment - Tests EN 60512-1 -
and measurements -
Part 1: General
IEC 60512-1-100 - Connectors for electronic equipment - Tests EN 60512-1-100 -
and measurements -
Part 1-100: General - Applicable publications

IEC 60512-26-100 - Connectors for electronic equipment - Tests EN 60512-26-100 -
and measurements -
Part 26-100: Measurement setup, test and
reference arrangements and measurements
for connectors according to IEC 60603-7 -
Tests 26a to 26g
IEC 60603-7 Series Connectors for electronic equipment EN 60603-7 Series

IEC 60603-7 2008 Connectors for electronic equipment - EN 60603-7 2009
Part 7: Detail specification for 8-way,
unshielded, free and fixed connectors

IEC 61076-1 - Connectors for electronic equipment - Product EN 61076-1 -
requirements -
Part 1: Generic specification
IEC 61156 Series Multicore and symmetrical pair/quad cables - -
for digital communications -
Part 1: Generic specification
IEC 61169-16 - Radio-frequency connectors - EN 61169-16 -
Part 16: Sectional specification - RF coaxial
connectors with inner diameter of outer
conductor 7 mm (0,276 in) with screw
coupling - Characteristics impedance 50 ohms
(75 ohms) (type N)
IEC 62153-4-12 - Metallic communication cable test methods - - -
Part 4-12: Electromagnetic compatibility
(EMC) - Coupling attenuation or screening
attenuation of connecting hardware -
Absorbing clamp method
IEC 60512-27-100 ®
Edition 1.0 2011-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Connectors for electronic equipment – Tests and measurements –
Part 27-100: Signal integrity tests up to 500 MHz on 60603-7 series connectors –
Tests 27a to 27g
Connecteurs pour équipements électroniques – Essais et mesures –
Partie 27-100: Essais d’intégrité des signaux jusqu’à 500 MHz sur les
connecteurs de la série CEI 60603-7 – Essais 27a à 27g

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX XB
ICS 31.220.10 ISBN 978-2-88912-823-5

– 2 – 60512-27-100 © IEC:2011
CONTENTS
FOREWORD . 6
1 Scope and object . 8
2 Normative references . 8
3 Terms, definitions, acronyms and symbols . 9
3.1 Terms and definitions . 9
3.1.1 Test Free Connector (TFC) . 9
3.2 Acronyms . 9
3.3 Symbols . 10
4 Overall test arrangement . 10
4.1 Test instrumentation . 10
4.2 Coaxial cables and interconnect for network analysers . 11
4.3 Measurement precautions . 11
4.4 Balun requirements . 11
4.5 Interfacing . 12
4.6 Reference components for calibration . 13
4.6.1 Reference loads for calibration . 13
4.6.2 Reference cables for calibration . 14
4.7 Termination loads for termination of conductor pairs . 14
4.7.1 General . 14
4.7.2 Resistor terminations . 14
4.7.3 Balun terminations . 15
4.7.4 Termination types . 15
4.8 Termination of screens . 15
4.9 Test specimen and reference planes . 15
4.9.1 General . 15
4.9.2 Interconnections between device under test (DUT) and the
calibration plane . 16
5 Connector measurement up to 500 MHz . 17
5.1 General . 17
5.2 Insertion loss, Test 27a . 17
5.2.1 Object . 17
5.2.2 Free connector for insertion loss. 17
5.2.3 Test method . 17
5.2.4 Test set-up . 17
5.2.5 Procedure . 18
5.2.6 Test report . 18
5.2.7 Accuracy . 19
5.3 Return loss, Test 27b . 19
5.3.1 Object . 19
5.3.2 Free connector for return loss . 19
5.3.3 Test method . 19
5.3.4 Test set-up . 19
5.3.5 Procedure . 19
5.3.6 Test report . 19
5.3.7 Accuracy . 19
5.4 Near-end crosstalk (NEXT), Test 27c . 20

60512-27-100 © IEC:2011 – 3 –
5.4.1 Object . 20
5.4.2 Free connector for NEXT . 20
5.4.3 Test method . 20
5.4.4 Test set-up . 20
5.4.5 Procedure . 21
5.4.6 Test report . 24
5.4.7 Accuracy . 24
5.5 Far-end crosstalk (FEXT), Test 27d . 24
5.5.1 Object . 24
5.5.2 Free connector for FEXT .
...