EN IEC 61754-13:2024

SLOVENSKI STANDARD
01-september-2024
Optični spojni elementi in pasivne komponente - Vmesniki za optične konektorje -
13. del: Družina konektorjev vrste FC-PC (IEC 61754-13:2024)
Fibre optic interconnecting devices and passive components - Fibre optic connector
interfaces - Part 13: Type FC-PC connector family (IEC 61754-13:2024)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von
Lichtwellenleiter-Steckverbindern - Teil 13: Steckverbinderfamilie der Bauart FC-PC (IEC
61754-13:2024)
Dispositifs d'interconnexion et composants passifs fibroniques - Interfaces de
connecteurs fibroniques - Partie 13: Famille de connecteurs de type FC-PC (IEC 61754-
13:2024)
Ta slovenski standard je istoveten z: EN IEC 61754-13:2024
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61754-13

NORME EUROPÉENNE
EUROPÄISCHE NORM June 2024
ICS 33.180.20 Supersedes EN 61754-13:2006
English Version
Fibre optic interconnecting devices and passive components -
Fibre optic connector interfaces - Part 13: Type FC-PC
connector family
(IEC 61754-13:2024)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Interfaces de connecteurs fibroniques - Partie Bauteile - Steckgesichter von Lichtwellenleiter-
13: Famille de connecteurs de type FC-PC Steckverbindern - Teil 13: Steckverbinderfamilie der Bauart
(IEC 61754-13:2024) FC-PC
(IEC 61754-13:2024)
This European Standard was approved by CENELEC on 2024-06-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61754-13:2024 E

European foreword
The text of document 86B/4874/FDIS, future edition 3 of IEC 61754-13, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61754-13:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-03-17
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-06-17
document have to be withdrawn
This document supersedes EN 61754-13:2006 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61754-13:2024 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 61300-3-22 NOTE Approved as EN 61300-3-22
IEC 63267-2-1 NOTE Approved as EN IEC 63267-2-1
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 61754-1 -  Fibre optic interconnecting devices and EN 61754-1 -
passive components - Fibre optic
connector interfaces - Part 1: General and
guidance
IEC 61755-3-1 -  Fibre optic interconnecting devices and EN IEC 61755-3-1 -
passive components - Connector optical
interfaces - Part 3-1: Connector
parameters of dispersion unshifted single-
mode physically contacting fibres - Non-
angled 2,5 mm and 1,25 mm diameter
cylindrical full zirconia ferrules

IEC 61754-13 ®
Edition 3.0 2024-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Fibre optic

connector interfaces –
Part 13: Type FC-PC connector family

Dispositifs d'interconnexion et composants passifs fibroniques – Interfaces de

connecteurs fibroniques –
Partie 13: Famille de connecteurs de type FC-PC

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20  ISBN 978-2-8322-8830-6

– 2 – IEC 61754-13:2024 © IEC 2024
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Description . 5
5 Interfaces . 6
5.1 General . 6
5.2 Intermateability . 6
5.3 Interfaces and dimensions . 6
Bibliography . 15

Figure 1 – Plug connector interface . 7
Figure 2 – Adaptor connector interface . 10
Figure 3 – Pin gauge for adaptor . 11
Figure 4 – Active device receptacle interface . 12
Figure 5 – Pin gauge for active device receptacle . 14

Table 1 – Intermateability of interfaces . 6
Table 2 – Dimensions of the plug connector interface . 8
Table 3 – Grade characteristics for plug connector . 9
Table 4 – Dimensions of the adaptor connector interface . 11
Table 5 – Pin gauge dimensions . 11
Table 6 – Dimensions of the active device receptacle interface . 13
Table 7 – Alignment feature grade of the active device receptacle interface . 13
Table 8 – Pin gauge dimensions . 14

IEC 61754-13:2024 © IEC 2024 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
FIBRE OPTIC CONNECTOR INTERFACES –

Part 13: Type FC-PC connector family

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 61754-13 has been prepared by subcommittee 86B: Fibre optic interconnecting devices
and passive components, of IEC technical committee 86: Fibre optics. It is an International
Standard.
This third edition cancels and replaces the second edition published in 2006. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Revising normative reference reflecting the latest documents;
b) Addition of intermateability in 5.2;

---------------------
...