EN IEC 63033-2:2019

SLOVENSKI STANDARD
01-oktober-2019
Avtomobilski multimedijski sistemi in oprema - Sistem za nadzor vožnje - 2. del:
Načini snemanja sistema pri nadzoru vožnje (IEC 63033-2:2018)
Car multimedia systems and equipment - Drive monitoring system Part 2: Recording
methods of the drive monitoring system (IEC 63033-2:2018)
Multimediasysteme und -geräte in Fahrzeugen - Fahrüberwachungssystem - Teil 2:
Aufzeichnungsverfahren der Fahrüberwachungssysteme
(IEC 63033-2:2018)
Systèmes et équipements multimédias pour automobiles - Système de surveillance de la
conduite Partie 2: Méthodes d'enregistrement du système de surveillance de la conduite
(IEC 63033-2:2018)
Ta slovenski standard je istoveten z: EN IEC 63033-2:2019
ICS:
33.160.60 Večpredstavni (multimedijski) Multimedia systems and
sistemi in oprema za teleconferencing equipment
telekonference
43.060.50 Električna in elektronska Electrical and electronic
oprema. Krmilni sistemi equipment. Control systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 63033-2

NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2019
ICS 33.160; 43.040.15
English Version
Car multimedia systems and equipment - Drive monitoring
system Part 2: Recording methods of the drive monitoring
system
(IEC 63033-2:2018)
Systèmes et équipements multimédias pour automobiles - Multimediasysteme und -geräte in Fahrzeugen -
Système de surveillance de la conduite Partie 2: Méthodes Fahrüberwachungssystem - Teil 2: Aufzeichnungsverfahren
d'enregistrement du système de surveillance de la conduite der Fahrüberwachungssysteme
(IEC 63033-2:2018) (IEC 63033-2:2018)
This European Standard was approved by CENELEC on 2019-01-02. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63033-2:2019 E

European foreword
The text of document 100/3029/CDV, future edition 1 of IEC 63033-2, prepared by IEC/TC 100 "Audio,
video and multimedia systems and equipment" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 63033-2:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-10-02
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-01-02
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 63033-2:2018 was approved by CENELEC as a European
Standard without any modification.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC/TS 63033-1 2017 Car multimedia system and equipment - - -
Drive monitoring system - Part1:
General
IEC 63033-2 ®
Edition 1.0 2018-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Car multimedia systems and equipment – Drive monitoring system

Part 2: Recording methods of the drive monitoring system

Systèmes et équipements multimédias pour automobiles – Système de

surveillance de la conduite
Partie 2: Méthodes d'enregistrement du système de surveillance de la conduite

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.160; 43.040.15 ISBN 978-2-8322-6294-8

– 2 – IEC 63033-2:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 6
3.1 General . 6
3.2 Abbreviated terms . 6
4 System model . 6
4.1 General . 6
4.2 Video recording. 7
4.2.1 General . 7
4.2.2 Recording 1 . 7
4.2.3 Recording 2 . 8
5 Viewer . 10
5.1 General . 10
5.2 General viewer . 10
5.3 Enhanced viewer . 10

Figure 1 – Displaying and Recording system model of drive monitoring system . 7
Figure 2 – Raw video data example of recording 1, the image before composition . 7
Figure 3 – The composite video data example of recording 2 . 9
Figure 4 – Viewer example . 10

Table 1 – Metadata for recording 1 . 8
Table 2 – Metadata for dependent part of video data 1 . 8
Table 3 – Metadata for recording 2 . 9
Table 4 – Metadata for dependent part of video data 2 . 9

IEC 63033-2:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CAR MULTIMEDIA SYSTEMS AND EQUIPMENT –
DRIVE MONITORING SYSTEM
Part 2: Recording methods of the drive monitoring system

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 63033-2 has been prepared by IEC technical committee 100:
Audio, video and multimedia systems and equipment.
The text of this International Standard is based on the following documents:
CDV Report on voting
100/3029/CDV 100/3134/RVC
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – IEC 63033-2:2018 © IEC 2018
A list of all parts in the IEC 63033 series, published under the general title Car multimedia
systems and equipment – Drive monitoring system, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
IEC 63033-2:2018 © IEC 2018 – 5 –
INTRODUCTION
This document specifies
...