Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-4: Particular requirements - Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC 61557-8 and for equipment for insulation fault location according to IEC 61557-9

specifies more detailed test configurations, operational conditions and performance criteria than IEC 61326-1 for equipment for - insulation monitoring according to IEC 61557-8 -insulation fault location according to IEC 61557-9; This applies to insulation monitoring devices and insulation fault location systems permanently or semi-permanently connected to the distribution system.

Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-Anforderungen - Teil 2-4: Besondere Anforderungen - Prüfanordnung, Betriebsbedingungen und Leistungsmerkmale für Isolationsüberwachungsgeräte gemäß IEC 61557-8 und Geräte zur Isolationsfehlerortung gemäß IEC 61557-9

Matériel electrique de mesure, de commande et de laboratoire - Exigences relatives à la CEM - Partie 2-4: Exigences particulières - Configurations d'essai, conditions de fonctionnement et critères d'aptitude à la fonction pour les dispositifs de surveillance d'isolation en accord avec la CEI 61557-8 et pour les équipements de localisation de défaut d'isolation en accord avec la CEI 61557-9

spécifie plus en détail que la CEI 61326-1, les configurations d'essai, les conditions de fonctionnement et les critères d'aptitude à la fonction pour les équipements pour - la surveillance de l'isolation en accord avec la CEI 61557-8; -la localisation des fautes d'isolation en accord avec la CEI 61557-9. Elle s'applique aux dispositifs de surveillance de l'isolation et aux systèmes de localisation de fautes d'isolation permanents ou semi-permanents connectés au système de distribution

Električna oprema za merjenje, nadzor in laboratorijsko uporabo - Zahteve za elektromagnetno združljivost – 2-4. del: Posebne zahteve - Konfiguracije za preskus, pogoji obratovanja in kriteriji za lastnosti naprav za stalno preverjanje izolacije po IEC 61557-8 in opreme za ugotavljanje mesta okvare izolacije po IEC 61557-9 (IEC 61326-2-4:2006)

Člen 1 iz IEC 61326-1 se takole nanaša na sprejetje: Dodatek: Ta del IEC 61326 podrobneje označuje preskusne konfiguracije, pogoje delovanja in kriterije delovanja kot IEC 61326-1, za opremo za preverjanje izolacije glede na IEC 61557-8; - lokacija izolacijske napake glede na IEC 61557-9. To se nanaša na naprave za stalno preverjanje izolacije in sistem lokacij izolacijskih napak, ki so stalno ali delno vezane na distribucijski sistem.

General Information

Status
Withdrawn
Publication Date
05-Dec-2006
Withdrawal Date
31-Oct-2009
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
14-Aug-2015
Completion Date
14-Aug-2015

Relations

Buy Standard

Standard
EN 61326-2-4:2007
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2007
1DGRPHãþD
SIST EN 61326:1998
SIST EN 61326:1998/A1:1998
SIST EN 61326:1998/A2:2002
SIST EN 61326:1998/A3:2004
(OHNWULþQDRSUHPD]DPHUMHQMHQDG]RULQODERUDWRULMVNRXSRUDER=DKWHYH]D
HOHNWURPDJQHWQR]GUXåOMLYRVW±GHO3RVHEQH]DKWHYH.RQILJXUDFLMH]D
SUHVNXVSRJRMLREUDWRYDQMDLQNULWHULML]DODVWQRVWLQDSUDY]DVWDOQRSUHYHUMDQMH
L]RODFLMHSR,(&LQRSUHPH]DXJRWDYOMDQMHPHVWDRNYDUHL]RODFLMHSR,(&
 ,(&
Electrical equipment for measurement, control and laboratory use - EMC requirements --
Part 2-4: Particular requirements - Test configurations, operational conditions and
performance criteria for insulation monitoring devices according to IEC 61557-8 and for
equipment for insulation fault location according to IEC 61557-9
Ta slovenski standard je istoveten z: EN 61326-2-4:2006
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61326-2-4
NORME EUROPÉENNE
December 2006
EUROPÄISCHE NORM
ICS 25.040.40; 33.100 Supersedes EN 61326:1997 + A1:1998 + A2:2001 + A3:2003

English version
Electrical equipment for measurement, control and laboratory use -
EMC requirements
Part 2-4: Particular requirements
Test configurations, operational conditions and performance criteria
for insulation monitoring devices according to IEC 61557-8
and for equipment for insulation fault location according to IEC 61557-9
(IEC 61326-2-4:2006)
Matériel electrique de mesure,  Elektrische Mess-, Steuer-, Regel-
de commande et de laboratoire - und Laborgeräte -
Exigences relatives à la CEM EMV-Anforderungen
Partie 2-4: Exigences particulières - Teil 2-4: Besondere Anforderungen -
Configurations d'essai, conditions Prüfanordnung, Betriebsbedingungen
de fonctionnement et critères d'aptitude und Leistungsmerkmale
à la fonction pour les dispositifs für Isolationsüberwachungsgeräte gemäß
de surveillance d'isolation en accord IEC 61557-8 und Geräte
avec la CEI 61557-8 zur Isolationsfehlerortung gemäß
et pour les équipements de localisation IEC 61557-9
de défaut d'isolation en accord (IEC 61326-2-4:2006)
avec la CEI 61557-9
(CEI 61326-2-4:2006)
This European Standard was approved by CENELEC on 2006-11-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61326-2-4:2006 E
Foreword
The text of document 65A/473/FDIS, future edition 1 of IEC 61326-2-4, prepared by SC 65A, System
aspects, of IEC TC 65, Industrial-process measurement and control, was submitted to the IEC-CENELEC
parallel vote and was approved by CENELEC as EN 61326-2-4 on 2006-11-01.
The EN 61326 series supersedes EN 61326:1997 + corrigendum September 1998 + A1:1998 + A2:2001
+ A3:2003.
This part of EN 61326 is to be used in conjunction with EN 61326-1:2006 and follows the same
numbering of clauses, subclauses, tables and figures as that standard.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-08-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2009-11-01
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and covers essential requirements of
EC Directive 89/336/EEC. See Annex ZZ.
Annexes ZA and ZZ have been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61326-2-4:2006 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61326-2-4:2006
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
Addition to Annex ZA of EN 61326-1:2006:
1) 2)
IEC 61000-4-2 - Electromagnetic compatibility (EMC) EN 61000-4-2 1995
Part 4-2: Testing and measurement
techniques - Electrostatic discharge immunity
test
1) 2)
IEC 61000-4-3 - Electromagnetic compatibility (EMC) EN 61000-4-3 2006
Part 4-3 : Testing and measurement
techniques - Radiated, radio-frequency,
electromagnetic field immunity test

1) 2)
IEC 61000-4-4 - Electromagnetic compatibility (EMC) EN 61000-4-4 2004
Part 4-4: Testing and measurement
techniques - Electrical fast transient/burst
immunity test
1) 2)
IEC 61000-4-5 - Electromagnetic compatibility (EMC) EN 61000-4-5 2006
Part 4-5: Testing and measurement
techniques - Surge immunity test

1) 2)
IEC 61000-4-6 - Electromagnetic compatibility (EMC) EN 61000-4-6 1996
Part 4-6: Testing and measurement
techniques - Immunity to conducted
disturbances, induced by radio-frequency
fields
1) 2)
IEC 61000-4-8 - Electromagnetic compatibility (EMC) EN 61000-4-8 1993
Part 4-8: Testing and measurement
techniques - Power frequency magnetic field
immunity test
1) 2)
IEC 61000-4-11 - Electromagnetic compatibility (EMC) EN 61000-4-11 2004
Part 4-11: Testing and measurement
techniques - Voltage dips, short interruptions
and voltage variations immunity tests

IEC 61326-1 2005 Electrical equipment for measurement, EN 61326-1 2006
control and laboratory use - EMC
requirements
Part 1: General requirements
1)
Undated reference.
2)
Valid edition at date of issue.

Publication Year Title EN/HD Year
1) 2)
IEC 61557-8 - Electrical safety in low voltage distribution EN 61557-8 1997
systems up to 1 000 V a.c. and 1 500 V d.c. -
Equipment for testing, measuring or
monitoring of protective measures
Part 8: Insulation monitoring devices for IT
systems
1) 2)
IEC 61557-9 - Electrical safety in low voltage distribution EN 61557-9 1999
systems up to 1 000 V a.c. and 1 500 V d.c. -
Equipment for testing, measuring or
monitoring of protective measures
Part 9: Equipment for insulation fault location
in IT systems
1) 3)
CISPR 11 (mod) - Industrial scientific and medical (ISM) radio- EN 55011 200X
frequency equipment - Electromagnetic
disturbance characteristics - Limits and
methods of measurement
3)
To be published.
- 5 - EN 61326-2-4:2006
Annex ZZ
(informative)
Coverage of Essential Requirements of EC Directives
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant essential requirements as given in Article 4 of the EC Directive 89/336/EEC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within
the scope of this standard.
___________
NORME CEI
INTERNATIONALE
IEC
61326-2-4
INTERNATIONAL
Première édition
STANDARD
First edition
2006-06
Matériel électrique de mesure, de commande
et de laboratoire – Exigences relatives à la CEM –
Partie 2-4:
Exigences particulières – Configurations d'essai,
conditions de fonctionnement et critères
d'aptitude à la fonction pour les dispositifs de
surveillance d'isolation en accord avec la
CEI 61557-8 et pour les équipements de
localisation de défaut d'isolation en accord
avec la CEI 61557-9
Electrical equipment for measurement, control
and laboratory use – EMC requirements –
Part 2-4:
Particular requirements – Test configurations,
operational conditions and performance criteria
for insulation monitoring devices according to
IEC 61557-8 and for equipment for insulation
fault location according to IEC 61557-9
 IEC 2006 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
L
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

61326-2-4  IEC:2006 – 3 –
CONTENTS
FOREWORD.5

1 Scope.9
2 Normative references .9
3 Terms and definitions .11
4 General .13
5 EMC test plan.13
5.1 General .13
5.2 Configuration of EUT during testing.13
5.3 Operation conditions of EUT during testing.15
5.4 Specification of performance criteria .15
5.5 Test description.15
6 Immunity requirements .15
6.1 Conditions during the tests .15
6.2 Immunity test requirements .17
6.3 Random aspects .19
6.4 Performance criteria .19
7 Emission requirements .21
7.1 Conditions during measurements. .21
7.2 Emission limits .21
8 Test results and test report.23
9 Instructions for use.23

Table 101 – Immunity tests .17
Table 102 – Immunity requirements, performance criteria .19

61326-2-4  IEC:2006 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL EQUIPMENT FOR MEASUREMENT,
CONTROL AND LABORATORY USE –
EMC REQUIREMENTS –
Part 2-4: Particular requirements – Test configurations,
operational conditions and performance criteria for insulation
monitoring devices according to IEC 61557-8 and for equipment
for insulation fault location accordin
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.