EN 508-2:2019
(Main)Roofing and cladding products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 2: Aluminium
Roofing and cladding products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 2: Aluminium
This part of EN 508 specifies requirements for self-supporting external profiled sheets for roof covering, wall cladding, lining and liner tray products for discontinuous laying made from aluminium sheet with or without surface treatment (additional organic coatings or anodising).
This document establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are made available on the market before being despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.
This document applies to all discontinuously laid self-supporting external profiled sheets for roof covering, wall cladding, lining and liner trays with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building, and to transfer any resultant loads and infrequent maintenance loads to the structure.
This document does not cover products for structural purposes, i.e. it does cover products used in structural class III (according to EN 1999-1-4), it does not cover products used in constructions of Structural Classes I and II (according to EN 1999-1-4) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance of permanent static loads (excluding self-weight of the metal sheet).
No requirements for supporting construction, design of roof system and execution of connections and flashings are included.
Dachdeckungs‑ und Wandbekleidungselemente aus Metallblech - Spezifikation für selbsttragende Bedachungselemente aus Stahlblech, Aluminiumblech oder nichtrostendem Stahlblech - Teil 2: Aluminium
Dieser Teil der EN 508 spezifiziert die Anforderungen an selbsttragende Außen-Profilbleche für Dacheindeckung, Wandbekleidung, Verblendung und Kassettenprodukte zur diskontinuierlichen Verlegung aus Aluminiumblech mit oder ohne Oberflächenbehandlung (zusätzliche organische Beschichtungen oder Anodisierung).
Dieses Dokument legt die allgemeinen Merkmale, Definitionen, Klassifizierungen und Beschriftung für die Produkte gemeinsam mit Anforderungen an die Materialien, aus denen die Produkte hergestellt werden können, fest. Es ist vorgesehen für die Verwendung entweder durch den Hersteller, der damit sicherstellt, dass seine Produkte den Anforderungen genügen, oder durch Kunden zur Überprüfung, ob die Produkte anforderungsgemäß sind, bevor sie aus der Fabrik versandt und auf dem Markt angeboten werden. Sie spezifiziert die Anforderungen an Produkte, die diesen ermöglichen, allen normalen Einsatzbedingungen zu genügen.
Dieses Dokument gilt für alle diskontinuierlich verlegten selbsttragenden Außen-Profilbleche für die Dacheindeckung, Wandbekleidung und Verblendung sowie für Kassettenprofile, nicht jedoch für Dachpfannen mit einer Fläche von unter 1 m2, die durch Stanzen hergestellt wurden. Diese Profil-Dachbleche sind dafür ausgelegt, das Eindringen von Wind, Regen und Schnee in das Gebäude zu verhindern und jegliche aus diesen und aus unregelmäßiger Wartung resultierenden Lasten auf das Gebäude zu übertragen.
Diese Norm gilt nicht für Produkte für tragende Zwecke, d. h. sie gilt für Produkte, die in Konstruktionsklasse III (nach EN 1999 1 4) verwendet werden, und sie gilt nicht für Produkte, die in Bauten der Konstruktionsklassen I und II (nach EN 1999 1 4) verwendet werden, die für einen Beitrag zur gesamten oder teilweisen Stabilität der Gebäudestruktur vorgesehen sind, indem sie Widerstand gegen Streckung oder gegen dauerhafte statische Lasten bereitstellen (außer Eigengewicht des Metallblechs).
Anforderungen an die Unterkonstruktion, die Konstruktion des Dachsystems und die Ausführung von Verbindungen und Kehlblechen sind nicht enthalten.
Produits de couverture et bardage en tôle métallique - Spécification pour les plaques de couverture en tôle d'acier, d'aluminium ou d'acier inoxydable - Partie 2 : Aluminium
La présente partie de l'EN 508 spécifie les prescriptions relatives aux produits autoportants de couverture, bardages intérieurs et extérieurs, cloisons pour pose en discontinu en tôle d'aluminium avec ou sans traitement de surface (revêtements organiques supplémentaires ou anodisation).
Le présent document établit les caractéristiques générales, les définitions, les classifications et l'étiquetage applicables aux produits, de même que les prescriptions relatives aux matériaux à partir desquels les produits peuvent être fabriqués. Il est destiné à être utilisé soit par des fabricants en vue de démontrer que leurs produits sont conformes aux prescriptions, soit par des acheteurs pour vérifier que les produits sont conformes avant leur mise à disposition sur le marché, avant leur expédition de l’usine. Il spécifie les prescriptions relatives aux produits pour leur permettre de répondre à toutes les conditions normales en service.
Le présent document s'applique à toutes les plaques autoportantes profilées extérieures de couverture, de bardages intérieurs et extérieurs, de cloisons posées en discontinu, à l'exception des dalles d'une surface inférieure à 1 m² et produites par emboutissage. Ces plaques profilées sont conçues pour empêcher le vent, la pluie et la neige de pénétrer dans le bâtiment et transmettent à la structure porteuse les charges qui en résultent ainsi que les charges occasionnelles dues aux opérations d'entretien.
Le présent document ne couvre pas les produits pour applications structurelles, c'est-à-dire qu'il couvre les produits utilisés dans la classe structurelle III (selon EN 1999-1-4), il ne couvre pas les produits destinés aux constructions de classes structurelles I et II (selon EN 1999-1-4) destinés à contribuer à la stabilité globale ou partielle de la structure du bâtiment ou apportant un contreventement ou une résistance aux charges statiques permanentes (à l'exclusion du poids propre de la plaque métallique).
Aucune exigence relative à la structure porteuse, à la conception du système de toiture et à la réalisation des assemblages et des finitions n'est incluse.
Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za samonosilne proizvode iz jeklene, aluminijeve pločevine ali pločevine iz nerjavnega jekla - 2. del: Aluminij
Ta del standarda EN 508 določa zahteve za samonosilne zunanje profilirane pločevine za strešne kritine, zunanje in notranje stenske obloge ter izdelke iz profilne kritine za nezvezno polaganje, izdelane iz aluminijeve pločevine s površinsko obdelavo ali brez nje (dodatne organske prevleke ali anodiziranje).
Ta standard določa splošne lastnosti, definicije, klasifikacije in označevanje za izdelke ter zahteve za materiale, iz katerih so izdelki lahko proizvedeni. Namenjen je proizvajalcem, da se zagotovi skladnost njihovih izdelkov z zahtevami, oziroma kupcem, da lahko preverijo skladnost izdelkov, še preden so ti dani na trg. Določa zahteve za izdelke, ki omogočajo, da slednji izpolnjujejo vse običajne pogoje uporabe.
Ta standard se uporablja za vse nezvezno položene samonosilne zunanje profilirane pločevine za strešne kritine, zunanje in notranje obloge ter profilne kritine z izjemo ploščic, ki imajo površino manjšo od 1 m2 in so izdelane z vtiskavanjem. Te profilirane strešne pločevine so zasnovane tako, da stavbo ščitijo pred vetrom, dežjem in snegom, pri čemer morebitne nastale obremenitve in obremenitve zaradi nerednega vzdrževanja prenesejo na konstrukcijo.
Ta standard ne zajema izdelkov za gradbene namene, kar pomeni, da ne zajema izdelkov, ki se uporabljajo pri strukturnem razredu III (v skladu s standardom EN 1999-1-4), ter izdelkov, ki se uporabljajo pri konstrukcijah strukturnih razredov I in II (v skladu s standardom EN 1999-1-4) in prispevajo k celotni ali delni stabilnosti gradbene konstrukcije tako, da zagotavljajo odpornost proti natezanju ali proti trajnim statičnim obremenitvam (brez lastne teže kovinske pločevine).
Standard ne vključuje zahtev za podporne konstrukcije, projektiranje strešnega sistema ter postavitev povezav in obrob.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2019
Nadomešča:
SIST EN 508-2:2008
Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za samonosilne
proizvode iz jeklene, aluminijeve pločevine ali pločevine iz nerjavnega jekla - 2.
del: Aluminij
Roofing and cladding products from metal sheet - Specification for self-supporting
products of steel, aluminium or stainless steel sheet - Part 2: Aluminium
Dachdeckungs- und Wandbekleidungselemente aus Metallblech - Spezifikation für
selbsttragende Bedachungselemente aus Stahlblech, Aluminiumblech oder
nichtrostende Stahlblech - Teil 2: Aluminium
Produits de couverture et bardage en tôle métallique - Spécification pour les plaques de
couverture en tôle d'acier, d'aluminium ou d'acier inoxydable - Partie 2 : Aluminium
Ta slovenski standard je istoveten z: EN 508-2:2019
ICS:
77.150.10 Aluminijski izdelki Aluminium products
91.060.20 Strehe Roofs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 508-2
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2019
EUROPÄISCHE NORM
ICS 91.060.20 Supersedes EN 508-2:2008
English Version
Roofing and cladding products from metal sheet -
Specification for self-supporting products of steel,
aluminium or stainless steel sheet - Part 2: Aluminium
Produits de couverture et bardage en tôle métallique - Dachdeckungs- und Wandbekleidungselemente aus
Spécification pour les plaques de couverture en tôle Metallblech - Spezifikation für selbsttragende
d'acier, d'aluminium ou d'acier inoxydable - Partie 2 : Bedachungselemente aus Stahlblech, Aluminiumblech
Aluminium oder nichtrostende Stahlblech - Teil 2: Aluminium
This European Standard was approved by CEN on 26 May 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 508-2:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions, symbols and abbreviations . 6
4 Requirements . 13
4.1 General . 13
4.2 Materials . 13
4.2.1 Aluminium . 13
4.2.2 Organic coatings . 14
4.2.3 Anodizing . 14
4.3 Products . 15
4.3.1 Mechanical resistance . 15
4.3.2 Calculation and tests of mechanical resistance . 15
4.3.3 Dimensions . 15
4.3.4 Dimensional tolerances for the profiled sheet . 15
4.3.5 Safety in case of fire . 16
5 Test methods . 16
5.1 Material properties . 16
5.2 Surface properties . 16
5.3 Structural properties . 16
6 Designation. 17
7 Marking, labelling, packaging, special ordering conditions, transport, storage and
handling . 17
7.1 Marking and labelling . 17
7.2 Packaging and special ordering conditions . 17
7.3 Transport, storage and handling . 17
Annex A (normative) Dimensional tolerances . 19
A.1 Tolerances for trapezoidal sheets . 19
A.1.1 General . 19
A.1.2 Depth of profile . 19
A.1.3 Depth of stiffeners . 20
A.1.4 Pitch . 20
A.1.5 Widths of crown and valley . 21
A.1.6 Cover width . 21
A.1.7 Radius of bends . 22
A.1.8 Deviation from straightness . 23
A.1.9 Deviation from squareness . 24
A.1.10 Length . 25
A.1.11 Deviation of side lap . 26
A.1.12 Curve radius and angles . 26
A.2 Tolerances for sinusoidal profiles . 27
A.3 Tolerances on tiles . 27
A.3.1 General . 27
A.3.2 Depth of tile . 28
A.3.3 Web angular displacement (Figure A.12) . 28
A.3.4 Pitch . 28
A.3.5 Width of crown and valley (Figure A.14) . 29
A.3.6 Cover width . 29
A.3.7 Radius of bends . 30
A.3.8 Deviation from straightness . 31
A.3.9 Deviation from squareness . 31
A.3.10 Length . 32
A.3.11 Contraction or bulging . 32
A.4 Methods for measuring profiles . 32
A.4.1 General . 32
A.4.2 Depth of profile. 33
A.4.3 Depth of stiffeners . 33
A.4.4 Pitch . 33
A.4.5 Width of crown and valley . 34
A.4.6 Cover width . 35
A.4.7 Radius of bends . 35
A.4.8 Straightness . 35
A.4.9 Squareness . 35
A.4.10 Length . 35
A.4.11 Side laps . 35
A.4.12 Side lap ripple . 36
Annex B (informative) Test methods for concentrated load . 38
Bibliography . 39
European foreword
This document (EN 508-2:2019) has been prepared by Technical Committee CEN/TC 128 “Roof covering
for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2020, and conflicting national standards shall
be withdrawn at the latest by February 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 508-2:2008.
EN 508 Roofing and cladding products from metal sheet - Specification for self-supporting products of steel,
aluminium or stainless steel sheet consists of the following parts:
— Part 1: Steel;
— Part 2: Aluminium;
— Part 3: Stainless steel.
In comparison with EN 508-2:2008, the scope of the standard has been extended to cladding products.
Reference has been added to anodised aluminium sheets as well as to the A1 EU-classification without
further testing of aluminium products in accordance with Commission decision 2010/737/EC.
These changes or additions can be found in the following Clauses and subclauses: Clause 1; Clause 2;
3.1.1; 4.2.1; 4.2.3; 4.3.1; 4.3.5; 4.3.5.2; 4.3.5.3; 5.3; Clause 6 and the Bibliography.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
Figure 1 indicates the position of this standard in the CEN framework of standards concerning roofing
and cladding products of metal sheet.
Figure 1 — Framework of standards
In this standard the performance of the product has been defined in terms of calculation and a number of
type tests.
The performance of a roof constructed with these products depends not only on the properties of the
product as required by this standard, but also on the design, construction and performance of the roof as
a whole in relation to the environment and conditions of use.
1 Scope
This part of EN 508 specifies requirements for self-supporting external profiled sheets for roof covering,
wall cladding, lining and liner tray products for discontinuous laying made from aluminium sheet with or
without surface treatment (additional organic coatings or anodising).
This document establishes general characteristics, definitions, classifications and labelling for the
products, together with requirements for the materials from which the products can be manufactured. It
is intended to be used either by manufacturers to ensure that their products comply with the
requirements or by purchasers to verify that the products comply before they are made available on the
market before being despatched from the factory. It specifies the requirements for products which enable
them to meet all normal service conditions.
This document applies to all discontinuously laid self-supporting external profiled sheets for roof
covering, wall cladding, lining and liner trays with the exception of tiles with a surface area less than 1 m
and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of
the building, and to transfer any resultant loads and infrequent maintenance loads to the structure.
This document does not cover products for structural purposes, i.e. it does cover products used in
structural class III (according to EN 1999-1-4), it does not cover products used in constructions of
Structural Classes I and II (according to EN 1999-1-4) intended to contribute to the global or partial
stability of the building structure by providing racking resistance or resistance of permanent static loads
(excluding self-weight of the metal sheet).
No requirements for supporting construction, design of roof system and execution of connections and
flashings are included.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 485-4, Aluminium and aluminium alloys — Sheet, strip and plate — Part 4: Tolerances on shape and
dimensions for cold-rolled products
EN 1396, Aluminium and aluminium alloys — Coil coated sheet and strip for general applications —
Specifications
EN 14782, Self-supporting metal sheet for roofing, external cladding and internal lining — Product
specification and requirements
EN ISO 7599, Anodizing of aluminium and its alloys — Method for specifying decorative and protective
anodic oxidation coatings on aluminium (ISO 7599)
3 Terms and definitions, symbols and abbreviations
3.1 General
For the purposes of this document, the terms and definitions given in EN 485-1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
NOTE Wherever the term aluminium is used it is meant unalloyed or alloyed aluminium.
3.1.1
self-supporting product
product which will, by virtue of its material and shape, support all applied loadings (e.g. snow, wind, foot
traffic, insulation, membrane), and transmit these loadings to spaced structural supports
3.2 Material definitions
3.2.1
temper
material conditions after a production stage, for example mechanical treatment and/or heat treatment,
intended to give the material physical and/or metallurgical properties
3.2.2
organic coated aluminium sheet
painted, post coated, laminated or coil coated (continuously organic coated) aluminium on one or on both
sides
3.2.3
anodized aluminium sheet
aluminium with an anodic coating, produced by an electrolytic oxidation process in which the surface of
the aluminium is converted to a mainly oxide coating having protective, decorative or functional
properties
3.3 Profile definitions
3.3.1
trapezoidal profiled sheet
self-supporting sheet which is designed to allow it to be side and end lapped, the crowns of which may
be rounded and, in addition, the crowns, web and valley may be stiffened
Note 1 to entry: See Figures 2, 3, 4 and 5.
Figure 2 — Part of typical trapezoidal profile
Figure 3 — Part of typical trapezoidal profile with rounded crowns
Figure 4 — Part of typical trapezoidal profile with stiffened crown and web
Figure 5 — Part of typical trapezoidal profile with stiffened valley
3.3.2
sinusoidal profiled sheet
self-supporting sheet which is designed to allow it to be side and end lapped, comprising a series of arc
shaped crowns and valleys interconnected with tangential webs
Note 1 to entry: See Figure 6.
Figure 6 — Part of typical sinusoidal profiled sheet
3.3.3
standing seam and concealed fix sheet
self-supporting sheet profiled in such a way that the fixings are hidden within the construction and are
not exposed to the weather
Note 1 to entry: See Figures 7 and 8.
Note 2 to entry: The profile shape is designed to allow the formation of side laps on site.
Note 3 to entry: As these types of roof covering and cladding products are used in proprietary roofing and
cladding systems, no structural requirements are given within this standard.
Note 4 to entry: These products are normally designed by testing.
Figure 7 — Typical standing seam profile
Figure 8 — Typical concealed fix profile
3.3.4
tile profile
part of typical tile profiled sheets that can allow the sheet to be side and/or end lapped
Note 1 to entry: See Figure 9 (a) b) and c)).
Note 2 to entry: The tile profiles may include transverse steps.
Note 3 to entry: As these types of roof covering products are used in proprietary systems no structural
requirements are given within this part of EN 508.
Note 4 to entry: These products are normally designed by testing.
Figure 9 — Typical tile profiles
3.4 Product geometry
NOTE The names for various parts of typical trapezoidal profiled sheets are given in Figure 10, Figure 11 with
additional definitions for sinusoidal profiles in Figure 12 and tile profiles in Figure 13.
Key
1 cover width 7 depth
2 valley stiffener 8 valley
3 rib 9 pitch
4 web stiffener 10 crown
5 trough 11 drainage groove
6 web 12 crown stiffener
Figure 10 — Definitions of the parts of typical trapezoidal profiled sheets
Key
1 bend radius
2 end lap
3 web angle
4 overlap
5 underlap
6 side lap in principle the same on tiles
Figure 11 — Definitions of the parts of typical trapezoidal profiled sheets
Key
1 depth
2 pitch
Figure 12 — Definitions of the parts of typical sinusoidal profiled sheets
Key
1 height of the step
2 length of the step
3 number of steps
4 end lap
Figure 13 — Definitions of the parts of typical tile
3.5 Symbols and abbreviations
For the purposes of this document, the following symbols and abbreviations apply.
EN AW The symbols for aluminium sheets are the alloy symbols as in 4.2.1
H Aluminium temper symbol
AY Acrylic paint coating
SP Polyester paint coating
SP-SI Silicone-modified polyester paint coating
PVDF Polyvinylidenefluoride paint coating
PVF(F) Polyvinylfluoride film coating
SP-PA Polyamid-modified polyester paint coating
PUR Polyurethane paint coating
PUR-PA Polyamide-modified polyurethane paint coating
AK Alkyd paint coating
EP Epoxy paint coating for use within a building
4 Requirements
4.1 General
The product shall be manufactured from materials complying with 4.2.
The supplier of the materials is responsible for carrying out the tests necessary to verify that the materials
supplied to the manufacturer comply with the requirements and should provide appropriate inspection
documents (according to EN 10204) on request.
NOTE The symbols and abbreviations to be used to designate the aluminium alloy, the type and thickness of
the organic coating are those of the standards referred to in Clause 2.
Product testing shall be provided to a defined schedule. A permanent quality system shall be adopted by
1)
the manufacturer .
4.2 Materials
4.2.1 Aluminium
Aluminium alloys given in Table 1 are suitable provided that their properties conform to the values given
in the relevant material standards (EN 485-2, EN 573-3).
Table 1 — Alloys of aluminium
Designation based on chemical
Numerical designation
symbol
EN AW-3003 EN AW-Al Mn1Cu
EN AW-3004 EN AW-Al Mn1Mg1
EN AW-3005 EN AW-Al Mn1Mg0,5
EN AW-
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...