M/BC/CEN/87/13 - CPD: pitched roofing products

This part of EN 12326 specifies test methods for slate and carbonate slate for roofing and wall cladding. It is applicable to natural roofing products as defined in EN 12326-1 used for assembly into discontinuous roofs and external wall cladding.
NOTE   Where the term "slate" is used in this document it means slate and carbonate slate unless otherwise indicated.

This European Standard specifies test methods for slate and carbonate slate for roofing and wall cladding. It is applicable to natural roofing products as defined in EN 12326-1 used for assembly into discontinuous roofs and external wall cladding.
NOTE   Where the term "slate" is used in this document it means slate and carbonate slate unless otherwise indicated.

This document applies to roof safety (building products) situated on the surface of pitched roofs and permanently fixed to the load-bearing roof construction. They are intended for the attachment of slaters’ ladders, for supporting working platforms and as anchorage points to which personal protective equipment against falls or for restraint are attached.
It specifies essential dimensions, materials to be used, requirements with respect to the load-bearing capacity, of the roof safety hooks fastened to the roof construction including their fastening system and the extent of testing.
This document does not apply to installations which are used exclusively as anchorage points to which personal protective equipment against falls or for restraint are attached (see EN 795).

This document applies to installations for roof access (building products) permanently fixed to the load-bearing construction of pitched roofs, to stand or to walk on during inspection, maintenance and repair of facilities on the roof.
It specifies essential dimensions, materials to be used, requirements with respect to the load-bearing capacity of the installation for roof access fastened to the roof construction including their fastening system, and the extent of testing.
This document does not apply to permanently fixed ladders on pitched roofs.

This document applies to roof safety (building products) situated on the surface of pitched roofs and permanently fixed to the load-bearing roof construction. They are intended for the attachment of slaters’ ladders, for supporting working platforms and as anchorage points to which personal protective equipment against falls or for restraint are attached.
It specifies essential dimensions, materials to be used, requirements with respect to the load-bearing capacity, of the roof safety hooks fastened to the roof construction including their fastening system and the extent of testing.
This document does not apply to installations which are used exclusively as anchorage points to which personal protective equipment against falls or for restraint are attached (see EN 795).

This document applies to installations for roof access (building products) permanently fixed to the load-bearing construction of pitched roofs, to stand or to walk on during inspection, maintenance and repair of facilities on the roof.
It specifies essential dimensions, materials to be used, requirements with respect to the load-bearing capacity of the installation for roof access fastened to the roof construction including their fastening system, and the extent of testing.
This document does not apply to permanently fixed ladders on pitched roofs.

This European Standard describes two test methods for testing the impermeability to water of clay roof tiles and fittings which can be considered as equivalent.

This European Standard describes two test methods for testing the impermeability to water of clay roof tiles and fittings which can be considered as equivalent.
NOTE   The methods are not applicable to all fittings, because of their different shapes.

This document specifies requirements for eaves gutters and rainwater down-pipes made from metal sheet. It establishes the general characteristics, designation system, classification, marking and quality requirements for the products.
The document applies to eaves gutters and external rainwater down-pipes that are supported by metal brackets and used to drain away rainwater. The shape and dimensions of a gutter are defined by the quantity of water to be drained away from the roof to the down-pipes and by architectural design requirements.
The document specifies the requirements for gutters and rainwater down-pipes which enable these products to meet all usual service conditions such as catching and draining away rainwater, melted snow or ice water from a building to a drainage system or a sewer outside the building.
Requirements for fixings, supporting construction, flashings or the method of making joints between the different components are not included in this document.
This document does not specify requirements for tolerances on dimensions for eaves gutters handmade on site.

This document specifies requirements and test methods of eaves gutters and fittings made from unplasticized poly(vinyl chloride) (PVC-U), and intended to be used for rainwater drainage.

This document specifies requirements for eaves gutters and rainwater down-pipes made from metal sheet. It establishes the general characteristics, designation system, classification, marking and quality requirements for the products.
The document applies to eaves gutters and external rainwater down-pipes that are supported by metal brackets and used to drain away rainwater. The shape and dimensions of a gutter are defined by the quantity of water to be drained away from the roof to the down-pipes and by architectural design requirements.
The document specifies the requirements for gutters and rainwater down-pipes which enable these products to meet all usual service conditions such as catching and draining away rainwater, melted snow or ice water from a building to a drainage system or a sewer outside the building.
Requirements for fixings, supporting construction, flashings or the method of making joints between the different components are not included in this document.
This document does not specify requirements for tolerances on dimensions for eaves gutters handmade on site.

This document specifies the requirements for rafter and fascia board brackets intended to support eaves gutters conforming to EN 607 or EN 612.

This document specifies requirements and test methods of eaves gutters and fittings made from unplasticized poly(vinyl chloride) (PVC-U), and intended to be used for rainwater drainage.

This document specifies the requirements for rafter and fascia board brackets intended to support eaves gutters conforming to EN 607 or EN 612.

This European Standard describes the test method used to evaluate the flexural strength of clay roofing tiles as defined in the standard EN YY - 'Clay roofing tiles - Product definitions and specifications'.

This European Standard describes the test method used to evaluate the flexural strength of clay roofing tiles as defined in the standard EN YY - 'Clay roofing tiles - Product definitions and specifications'.

This document specifies requirements for clay roofing tiles and fittings for pitched roof coverings and wall cladding and lining.
It applies to all tiles and fittings as defined in Clause 3.
Clay roofing tiles and clay fittings which conform to this document are suitable for use as roof coverings, vertical wall cladding and lining.
This document defines the minimum requirements for a product which if satisfactory at the time of delivery will ensure that the product is able to perform its function in relation to the performance levels declared for it, whilst subjected to the changes that occur in such materials during normal conditions of use.
The results obtained according to the Standard apply to products at the time they are offered for sale.

This document specifies requirements for clay roofing tiles and fittings for pitched roof coverings and wall cladding and lining.
It applies to all tiles and fittings as defined in Clause 3.
Clay roofing tiles and clay fittings which conform to this document are suitable for use as roof coverings, vertical wall cladding and lining.
This document defines the minimum requirements for a product which if satisfactory at the time of delivery will ensure that the product is able to perform its function in relation to the performance levels declared for it, whilst subjected to the changes that occur in such materials during normal conditions of use.
The results obtained according to the Standard apply to products at the time they are offered for sale.

This part of prEN 1013 specifies requirements for materials and performance of light transmitting profiled sheets of glass fibre reinforced polyester resin (GRP) intended for single skin roofing applications. It has to be read in conjunction with the general requirements contained in prEN 1013-1.

This part of EN 1013 specifies requirements for materials, methods of testing and performance of polycarbonate (PC) light transmitting profiled sheets produced to the desired profile by extrusion and/or forming for single skin applications. It is applicable in conjunction with the general requirements contained in EN 1013-1:1997. 1.2 Requirements are specified relative to: sheet thickness, visual characteristics, longitudinal reversion, retention of profile, multi-axial impact resistance, thermal ageing. Test methods are indicated as appropriate.

1.1. This part of EN 1013 specifies requirements for materials, methods of testing and performance of light transmitting profiled sheets of polymethylmethacrylate (PMMA) produced to the desired profile by extrusion and/or forming for single skin application. It is applicable in conjunction with the general requirements contained in EN 1013-1:1997. 1.2 Requirements are specified relative to: sheet thickness, width of the sheet, visual characteristics, longitudinal reversion, retention of profile, variation of impact strength after ageing and thermal ageing. Test procedures are indicated as appropriate.

This part of prEN 1013 specifies requirements for materials and performance of light transmitting profiled sheets of polyvinyl chloride produced to the desired profile by extrusion and/or forming for single skin applications. It has to be read in conjunction with the general requirements contained in prEN 1013-1. Requirements specified are relative to: sheet thickness, visual characteristics, longitudinal reversion, retention of profile, tensile impact strength, thermal ageing. Test methods are indicated as appropriate.

This part of EN 1013 specifies requirements for materials, methods of testing and performance of polycarbonate (PC) light transmitting profiled sheets produced to the desired profile by extrusion and/or forming for single skin applications. It is applicable in conjunction with the general requirements contained in EN 1013-1:1997. 1.2 Requirements are specified relative to: sheet thickness, visual characteristics, longitudinal reversion, retention of profile, multi-axial impact resistance, thermal ageing. Test methods are indicated as appropriate.

1.1. This part of EN 1013 specifies requirements for materials, methods of testing and performance of light transmitting profiled sheets of polymethylmethacrylate (PMMA) produced to the desired profile by extrusion and/or forming for single skin application. It is applicable in conjunction with the general requirements contained in EN 1013-1:1997. 1.2 Requirements are specified relative to: sheet thickness, width of the sheet, visual characteristics, longitudinal reversion, retention of profile, variation of impact strength after ageing and thermal ageing. Test procedures are indicated as appropriate.

This part of prEN 1013 specifies requirements for materials and performance of light transmitting profiled sheets of glass fibre reinforced polyester resin (GRP) intended for single skin roofing applications. It has to be read in conjunction with the general requirements contained in prEN 1013-1.

This part of prEN 1013 specifies requirements for materials and performance of light transmitting profiled sheets of polyvinyl chloride produced to the desired profile by extrusion and/or forming for single skin applications. It has to be read in conjunction with the general requirements contained in prEN 1013-1. Requirements specified are relative to: sheet thickness, visual characteristics, longitudinal reversion, retention of profile, tensile impact strength, thermal ageing. Test methods are indicated as appropriate.

To change the way in which reaction to fire of organically coated and glued products and fittings

This document specifies requirements for concrete roofing tiles and fittings for pitched roof coverings and wall cladding and lining.
Although concrete roofing tiles and fittings may incorporate surface coating, the specification of any surface coating is not included in this document.
NOTE 1   Information on surface characteristics is given in Annex A.
NOTE 2   Information on the performance of roof and wall assemblies is given in Annex B.

To change the way in which reaction to fire of organically coated and glued products and fittings

This document specifies requirements for concrete roofing tiles and fittings for pitched roof coverings and wall cladding and lining.
Although concrete roofing tiles and fittings may incorporate surface coating, the specification of any surface coating is not included in this document.
NOTE 1   Information on surface characteristics is given in Annex A.
NOTE 2   Information on the performance of roof and wall assemblies is given in Annex B.

This European Standard applies to bitumen shingles where the watertightness of the system is ensured by overlapping, by different adhesive systems or a combination of these, according to manufacturer's installation instructions, intended to be laid as covering for pitched roofs and/or wall cladding.
This European Standard applies only to bitumen shingles with a mineral reinforcement, synthetic reinforcement or a mixture of the two.
This European Standard does not apply to bitumen shingles having a mass of bitumen less than 1 300 g/m2.

This part of EN 12326 specifies test methods for roofing and wall cladding slates and other stones. It is applicable to natural roofing products as defined in prEN 12326-1 used for assembly into discontinuous roofs and wall cladding.

This European Standard applies to bitumen shingles where the watertightness of the system is ensured by overlapping, by different adhesive systems or a combination of these, according to manufacturer's installation instructions, intended to be laid as covering for pitched roofs and/or wall cladding.
This European Standard applies only to bitumen shingles with a mineral reinforcement, synthetic reinforcement or a mixture of the two.
This European Standard does not apply to bitumen shingles having a mass of bitumen less than 1 300 g/m2.

This part of EN 12326 specifies test methods for roofing and wall cladding slates and other stones. It is applicable to natural roofing products as defined in prEN 12326-1 used for assembly into discontinuous roofs and wall cladding.

This European Standard specifies the technical properties and establishes the test and inspection methods for finished corrugated bitumen sheets on leaving the factory. It also provides for the evaluation of conformity of products with the requirements of this standard.

This European Standard specifies the technical properties and establishes the test and inspection methods for finished corrugated bitumen sheets on leaving the factory. It also provides for the evaluation of conformity of products with the requirements of this standard..

This part of this European Standard specifies four test methods for the determination of frost resistance of clay roofing tiles and fittings to apply according to the geographic zone of use of the product under the conditions described in prEN1304.

This part of this European Standard specifies four test methods for the determination of frost resistance of clay roofing tiles and fittings to apply according to the geographic zone of use of the product under the conditions described in prEN1304.

This first part of the standard describes two test methods for testing the impermeability to water of clay roof tiles and fittings (*) which can be considered as equivalent.

This first part of the standard describes two test methods for testing the impermeability to water of clay roof tiles and fittings (*) which can be considered as equivalent.

Migrated from Progress Sheet (TC Comment) (2000-07-10): Res. 101 : acceptance of creation of amendment to EN 1304 (MB/990421) ++ (UAP 4 months)

This European standard defines clay roofing tiles and determines the general specifications to which they are bound as well as the rules for classification, marking and quality control of products. It applies to all tiles and fittings as defined in 4.1. Clay roofing tiles and clay fittings which conform to this standard are suitable for use as vertical cladding. The geometric and flexural strength criteria are not applicable to clay fittings or special tiles.

This European Standard specifies requirements for factory made eaves gutters andrainwater down-pipes made from metal sheet. It establishes the general characteristics, designation system, classification, marking and quality requirements for the products. The standard applies to eaves gutters and external rainwater down-pipes that are supported by metal brackets and used to drain away rainwater.

Migrated from Progress Sheet (TC Comment) (2000-07-10): Res. 101 : acceptance of creation of amendment to EN 1304 (MB/990421) ++ (UAP 4 months)

This European standard defines clay roofing tiles and determines the general specifications to which they are bound as well as the rules for classification, marking and quality control of products. It applies to all tiles and fittings as defined in 4.1. Clay roofing tiles and clay fittings which conform to this standard are suitable for use as vertical cladding. The geometric and flexural strength criteria are not applicable to clay fittings or special tiles.

Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months (CC/980407)

Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months (CC/980407)