EN 14044:2005/prA1

SLOVENSKI STANDARD
01-september-2008
Visoke nadzemne naprave za gasilske enote - Polavtomatske vrtljive gasilske
avtolestve - Zahteve za varnost in obnašanje v uporabi in preskusne metode
High rise aerial appliances for fire service use - Turntable ladders with sequential
movements - Safety and performance requirements and test methods
Hubrettungsfahrzeuge für die Feuerwehr - Drehleitern mit aufeinander folgenden
(sequenziellen) Bewegungen (Halbautomatik-Drehleitern) - Sicherheits- und
Leistungsanforderungen sowie Prüfverfahren
Moyens élévateurs aériens pour la lutte contre l'incendie - Echelles pivotantes à
mouvements séquentiels - Prescriptions de sécurité et des performances et méthodes
d'essais
Ta slovenski standard je istoveten z: EN 14044:2005/prA1
ICS:
13.220.10 Gašenje požara Fire-fighting
97.145 Lestve Ladders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 14044:2005
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
July 2008
ICS 13.220.10
English Version
High rise aerial appliances for fire service use - Turntable
ladders with sequential movements - Safety and performance
requirements and test methods
Moyens élévateurs aériens pour la lutte contre l'incendie - Hubrettungsfahrzeuge für die Feuerwehr - Drehleitern mit
Echelles pivotantes à mouvements séquentiels - aufeinander folgenden (sequenziellen) Bewegungen
Prescriptions de sécurité et des performances et méthodes (Halbautomatik-Drehleitern) - Sicherheits- und
d'essais Leistungsanforderungen sowie Prüfverfahren
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 192.
This draft amendment A1, if approved, will modify the European Standard EN 14044:2005. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14044:2005/prA1:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
th
1 Modification to the Foreword, 4 paragraph .4
2 Modification to 5.1.6.13.2.1, Cables .4
3 Modification to 5.1.6.13.3.1, Chains .4
4 Modification to 7.2.2, Operating instruction .4
5 Modification to 7.2.4, Information on commissioning .5
6 Modification to 7.2.7, Maintenance information for use by trained personnel.5
7 Modification to 7.3.1 .5
8 Addition of new Annex ZB .6

Foreword
This document (EN 14044:2005/prA1:2008) has been prepared by Technical Committee CEN/TC 192 “Fire
service equipment”, the secretariat of which is held by BSI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
The reason for amending the published standard EN 14044:2005 are as follows:
The revision of the EC-Machinery Directive 98/37/EC into 2006/42/EC requires the modification of published
European Standards cited in the Official Journal of the European Communities under that Directive. If no
amendment is made by the committee experts, then the standard would be updated with an Annex Z stating
that it does NOT meet the requirements of 2006/42/EC. This would result in the standard being removed from
the Official Journal and becoming a non-harmonized standard.
To keep the published standard EN 14044:2005 as a harmonized standard it was carefully checked against
the new EC-Machinery Directive 2006/42/EC and it was established that EN 14044:2005 meets the Essential
Health and Safety Requirements (EHSR) of the new EC-Machinery Directive 2006/42/EC in nearly all
requirements of the standard. Only a few requirements were established for a necessary amendment.
CEN/TC 19
...