iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14195:2005/AC:2006

(Corrigendum)

Metal framing components for gypsum plasterboard systems - Definitions, requirements and test methods

Metal framing components for gypsum plasterboard systems - Definitions, requirements and test methods

TC - Modification to the Scope

Metallprofile für Unterkonstruktionen für Gipsplatten Systemen - Begriffe, Anforderungen und Prüfverfahren

Eléments d'ossature métalliques pour systèmes en plaques de plâtre - Définitions, exigences et méthodes d'essai

Elementi s kovinskimi okvirji za mavčne plošče – Definicije, zahteve in preskusne metode

General Information

Status
Withdrawn
Publication Date
06-Jun-2006
Withdrawal Date
16-Dec-2014
ICS
77.140.70 - Steel profiles
91.100.10 - Cement. Gypsum. Lime. Mortar
Technical Committee
CEN/TC 241 - Gypsum and gypsum based products
Drafting Committee
CEN/TC 241/WG 3 - Board products
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
17-Dec-2014
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/106 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on gypsum products
Ref Project
SIST EN 14195:2005/AC:2006 - Metal framing components for gypsum plasterboard systems - Definitions, requirements and test methods

Relations

Replaced By
EN 14195:2014 - Metal framing components for gypsum board systems - Definitions, requirements and test methods
Effective Date
24-Dec-2014
Corrects
EN 14195:2005 - Metal framing components for gypsum plasterboard systems - Definitions, requirements and test methods
Effective Date
08-Jun-2022

Buy Standard

EN 14195:2005/AC:2006EN 14195:2005/AC:2006
PreviousNext
Corrigendum
EN 14195:2005/AC:2006
English, French and German language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Metal framing components for gypsum plasterboard systems - Definitions, requirements and test methodsPHWRGHEléments d'ossature métalliques pour systemes en plaques de plâtre - Définitions, exigences et méthodes d'essaiMetallprofile für Unterkonstruktionen für Gipsplatten Systemen - Begriffe, Anforderungen und PrüfverfahrenTa slovenski standard je istoveten z:EN 14195:2005/AC:2006SIST EN 14195:2005/AC:2006en,fr,de91.100.10Cement. Mavec. Apno. MaltaCement. Gypsum. Lime. Mortar77.140.70Jekleni profiliSteel profilesICS:SLOVENSKI
STANDARDSIST EN 14195:2005/AC:200601-september-2006

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14195:2005/ACJune 2006Juin 2006Juni 2006ICS 77.140.70; 91.100.10English versionVersion FrançaiseDeutsche FassungMetal framing components for gypsum plasterboard systems - Definitions,requirements and test methodsEléments d'ossature métalliques poursystèmes en plaques de plâtre - Définitions,exigences et méthodes d'essaiMetallprofile für Unterkonstruktionen fürGipsplatten Systemen - Begriffe,Anforderungen und PrüfverfahrenThis corrigendum becomes effective on 7 June 2006 for incorporation in the three official languageversions of the EN.Ce corrigendum prendra effet le 7 juin 2006 pour incorporation dans les trois versions linguistiquesoffi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 14195:2014(Main)
Metal framing components for gypsum board systems - Definitions, requirements and test methods
SIST EN 14195:2015

This European Standard specifies the characteristics of metal framing components (e.g. profiles, hangers and connectors) intended to be used in building construction works in conjunction with gypsum boards manufactured according to EN 520, EN 15283 1 and EN 15283 2 and gypsum board products from reprocessing conforming to EN 14190 where the assembly is non-loadbearing. Such assemblies include, for example, partitions, wall and ceiling linings, ceilings with mechanically fixed boards and the cladding of beams, columns, ducts and shafts.
It covers the following performance characteristics: reaction to fire, flexural (yield) strength and loadbearing capacity of suspension components to be measured according to the relevant test methods as specified or cited in this European Standard.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14195:2014/FprA1(Amendment)
Metal framing components for gypsum board systems - Definitions, requirements and test methods
SIST EN 14195:2015/oprA1:2018

This European Standard specifies the characteristics of metal framing components (e.g. profiles, hangers and connectors) intended to be used in building construction works in conjunction with gypsum boards manufactured according to EN 520, EN 15283 1 and EN 15283 2 and gypsum board products from reprocessing conforming to EN 14190 where the assembly is non-loadbearing. Such assemblies include, for example, partitions, wall and ceiling linings, ceilings with mechanically fixed boards and the cladding of beams, columns, ducts and shafts.
It covers the following performance characteristics: reaction to fire, flexural (yield) strength and loadbearing capacity of suspension components to be measured according to the relevant test methods as specified or cited in this European Standard.
Amendment: Delete the second paragraph.

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14195:2014(Main)
Metal framing components for gypsum board systems - Definitions, requirements and test methods
SIST EN 14195:2015

This European Standard specifies the characteristics of metal framing components (e.g. profiles, hangers and connectors) intended to be used in building construction works in conjunction with gypsum boards manufactured according to EN 520, EN 15283 1 and EN 15283 2 and gypsum board products from reprocessing conforming to EN 14190 where the assembly is non-loadbearing. Such assemblies include, for example, partitions, wall and ceiling linings, ceilings with mechanically fixed boards and the cladding of beams, columns, ducts and shafts.
It covers the following performance characteristics: reaction to fire, flexural (yield) strength and loadbearing capacity of suspension components to be measured according to the relevant test methods as specified or cited in this European Standard.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14195:2014/FprA1(Amendment)
Metal framing components for gypsum board systems - Definitions, requirements and test methods
SIST EN 14195:2015/oprA1:2018

This European Standard specifies the characteristics of metal framing components (e.g. profiles, hangers and connectors) intended to be used in building construction works in conjunction with gypsum boards manufactured according to EN 520, EN 15283 1 and EN 15283 2 and gypsum board products from reprocessing conforming to EN 14190 where the assembly is non-loadbearing. Such assemblies include, for example, partitions, wall and ceiling linings, ceilings with mechanically fixed boards and the cladding of beams, columns, ducts and shafts.
It covers the following performance characteristics: reaction to fire, flexural (yield) strength and loadbearing capacity of suspension components to be measured according to the relevant test methods as specified or cited in this European Standard.
Amendment: Delete the second paragraph.

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17928-1:2024(Main)
Gas infrastructure - Injection stations - Part 1: General requirements
kSIST FprEN 17928-1:2024

This document establishes the functional requirements for stations for the injection of biomethane, substitute natural gas (SNG) and hydrogen into gas transmission and distribution systems operated with gases (natural gas, biomethane, SNG, hydrogen, gas mixtures) in accordance with European technical rules that ensure the interoperability of systems.
Figure 1 describes the general approach including all the relevant functions that can be installed in different configurations. The injection of Hydrogen is covered separately in EN 17928-3:2024.
This document also applies to refeeding stations that feed such gases back into upstream gas supply networks; see Figure 2.
This document represents the state of the art at the time of its preparation.
This document does not apply to injection stations operating prior to the publication of this document.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
—   legislation/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13237:2024(Main)
Potentially explosive atmospheres - Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres
oSIST prEN 13237:2022

This document specifies terms and definitions (vocabulary) to be used in suitable standards dealing with equipment and protective systems intended for use in potentially explosive atmospheres within the scope of Directive 2014/34/EU.
NOTE   Terms and definitions avoid misunderstandings that are important in relation to the essential health and safety requirements of Directive 2014/34/EU.

  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-7:2024(Main)
Woodworking machines - Safety - Part 7: Surface planing, thickness planing and combined surface/thickness planing machines (ISO 19085-7:2024)
kSIST FprEN ISO 19085-7:2024

This document specifies the safety requirements and measures for
—     surface planing machines, also called jointers,
—     thickness planing machines, also called planers or single surface planers, and
—     combined surface/thickness planing machines
with fixed cutter block position, with an integrated feed in thickness planing mode, with or without demountable power feed device in planing mode, with manual loading and/or unloading of the workpiece, and capable of continuous production use, altogether referred to as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer. Reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with.
This document does not apply to:
a)       machines with more than one cutter block;
b)       machines with a mortising unit driven by a separate motor;
c)        machines where the cutter block is adjustable for depth of cut setting in thickness planing mode;
d)       machines where the conversion from planing to thickness planing mode or vice versa is achieved by mounting or demounting parts/units;
e)       machines where surface planing and thickness planing can be performed at the same time;
f)         machines intended for use in potentially explosive atmosphere;
g)       machines manufactured prior to the publication of this document.

  • Draft
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2350:2024(Main)
Aerospace series - Circuit breakers - Technical specification
kSIST FprEN 2350:2024
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 927-15:2024(Main)
Paints and varnishes - Coating materials and coating systems for exterior wood - Part 15: Assessment of bleeding of coloured wood extractives through a coating by means of a water immersion test
kSIST-TS FprCEN/TS 927-15:2024

This document specifies a test method using water immersion test for assessing the bleeding of coloured wood extractives through a coating. Leachates of coated and uncoated wood are collected after the immersion procedure and their colour is compared. The colour of the coated wood before and after immersion tests is also compared. This document does not specify acceptance values for colour differences that can be tolerated and it is not applicable to staining caused by knots for which there is a different test method (see EN 927 7).
NOTE   The method has been developed for oak and chestnut wood and might be applicable for other wood substrates containing water soluble extractives.

  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-5:2024(Main)
Woodworking machines - Safety - Part 5: Dimension saws (ISO 19085-5:2024)
kSIST FprEN ISO 19085-5:2024

This document specifies the safety requirements and measures for dimension saws (defined in 3.1), capable of continuous production use and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)       device to raise and lower the main saw blade and scoring saw blade;
b)       device to tilt the main saw blade and scoring saw blade for angled cutting in one or both directions;
c)        device for scoring;
d)       device for grooving with milling tool with a width not exceeding 20 mm;
e)       demountable power feed unit;
f)         power-operated sliding table;
g)       workpiece clamping.
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Draft
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day