EN ISO 11299-3:2013

SLOVENSKI STANDARD
01-april-2013
1DGRPHãþD
SIST EN 14408-3:2005
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo s
plinom - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11299-3:2011)
Plastics piping systems for renovation of underground gas supply networks - Part 3:
Lining with close-fit pipes (ISO 11299-3:2011)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten
Gasversorgungsnetzwerken - Teil 3: Close-Fit-Lining (ISO 11299-3:2011)
Systèmes de canalisations en plastique pour la rénovation des réseaux de gaz enterrés -
Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11299-3:2011)
Ta slovenski standard je istoveten z: EN ISO 11299-3:2013
ICS:
83.140.30 Cevi, fitingi in ventili iz Plastics pipes, fittings and
polimernih materialov valves
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11299-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2013
ICS 23.040.20; 23.040.45; 75.200 Supersedes EN 14408-3:2004
English Version
Plastics piping systems for renovation of underground gas
supply networks - Part 3: Lining with close-fit pipes (ISO 11299-
3:2011)
Systèmes de canalisations en plastique pour la rénovation Kunststoff-Rohrleitungssysteme für die Renovierung von
des réseaux de gaz enterrés - Partie 3: Tubage par tuyau erdverlegten Gasversorgungsnetzwerken - Teil 3: Close-Fit-
continu sans espace annulaire (ISO 11299-3:2011) Lining (ISO 11299-3:2011)
This European Standard was approved by CEN on 5 February 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11299-3:2013: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
The text of ISO 11299-3:2011 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 11299-3:2013 by Technical Committee CEN/TC 155 “Plastics piping systems and
ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at
the latest by August 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14408-3:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11299-3:2011 has been approved by CEN as EN ISO 11299-3:2013 without any modification.
INTERNATIONAL  ISO
STANDARD 11299-3
First edition
2011-09-15
Plastics piping systems for renovation of
underground gas supply networks
Part 3:
Lining with close-fit pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux de
gaz enterrés — Partie 3: Tubage par tuyau continu sans espace annulaire
Reference number
ISO 11299-3:2011(E)
©
ISO 2011
ISO 11299-3:2011(E)
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

ISO 11299-3:2011(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 General . 1
3.2 Techniques . 2
3.3 Characteristics . 2
3.4 Materials . 2
3.5 Product stages . 2
3.6 Service conditions . 2
3.7 Joints . 2
4 Symbols and abbreviated terms . 3
4.1 Symbols . 3
4.2 Abbreviated terms . 3
5 Pipes at the “M” stage . 3
5.1 Materials . 3
5.2 General characteristics . 4
5.3 Material characteristics . 4
5.4 Geometric characteristics . 4
5.5 Mechanical characteristics . 4
5.6 Physical characteristics . 5
5.7 Jointing . 5
5.8 Marking . 5
6 Fittings at the “M” stage . 5
7 Ancillary components . 5
8 Fitness for purpose of the installed lining system at the “I” stage . 5
8.1 Materials . 5
8.2 General characteristics . 5
8.3 Material characteristics . 5
8.4 Geometric characteristics . 6
8.5 Mechanical characteristics . 6
8.6 Physical characteristics . 7
8.7 Additional characteristics . 7
8.8 Sampling . 8
9 Installation practice . 8
9.1 Preparatory work . 8
9.2 Storage, handling and transport of pipes and fittings . 8
9.3 Equipment . 8
9.4 Installation . 9
9.5 Process-related inspection and testing .10
Annex A (normative) Factory-folded heat-reverted polyethylene (PE) pipe — Determination of memory
ability . 11
Bibliography .13
© ISO 2011 – All rights reserved  iii

ISO 11299-3:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
Int
...