iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13063-3:2007

(Main)

Chimneys - System chimneys with clay/ceramic flue liners - Part 3: Requirements and test methods for air flue system chimneys

Chimneys - System chimneys with clay/ceramic flue liners - Part 3: Requirements and test methods for air flue system chimneys

This product standard specifies the requirements and test methods for dry (designated D) and/or wet (designated W) air flue system chimneys, including terminals in which the products of combustion are conveyed to the atmosphere through clay/ceramic flue liners and combustion air is conveyed to suitable room-sealed appliances through an air duct or an air gap.
It also specifies the requirements for marking, manufacturer's instructions, product information and evaluation of conformity.
This standard does not apply to structurally independent (free standing or self supporting) system chimneys.
An air flue system chimney is made of the following components where appropriate:
-   clay/ceramic flue liners;
-   insulation layer;
-   outer walls;
-   mortar for jointing flue liners;
-   acid resistant mortar or elastomeric sealant for jointing flue liners;
-   mortar for jointing outer walls;
-   terminal;
-   chimney base;
-   pressure equalising opening;
-   air duct;
-   air gap;
-   cladding;
-   opening section;
-   cleaning and inspection door;
-   distance piece;
-   reinforcement.
The air- flue system chimney covers a combination of compatible chimney components obtained or specified from one manufacturing source, with product responsibility for the whole chimney.

Abgasanlagen - System-Abgasanlagen mit Keramik-Innenrohren - Teil 3: Anforderungen und Prüfungen für Luft-Abgasleitungen

Conduits de fumées - Conduits systèmes avec conduit intérieur en terre cuite/céramique - Partie 3 : Exigences et méthodes d'essai pour conduits systèmes air / fumée

La présente norme de produit spécifie les exigences et les méthodes d'essai applicables aux conduits systèmes air / fumée fonctionnant en condition sèche (désignation D) et/ou humide (désignation W), incluant des terminaux dans lesquels les produits de combustion sont acheminés vers l'atmosphère par des conduits intérieurs en terre cuite / céramique et l'air de combustion est acheminé aux chaudières étanches par un conduit d'air ou par un espace libre pour l’air.
Elle spécifie également les exigences de marquage, les instructions du fabricant, les informations relatives au produit et l'évaluation de la conformité.
La présente norme ne s'applique pas aux conduits systèmes structurellement indépendants (autoporteurs ou autonomes).
Un conduit système air / fumée se compose des éléments suivants, selon le cas :
   un conduit intérieur en terre cuite / céramique ;
   une couche d'isolant ;
   des enveloppes extérieures ;
   un mortier pour jointoyer les conduits intérieurs ;
   un mortier résistant aux acides pour jointoyer les conduits intérieurs ou un matériau d'étanchéité élastomère ;
   du mortier pour jointoyer les enveloppes extérieures ;
   un terminal ;
   une base ;
   une ouverture d'égalisation de pression ;
   un conduit d'air ;
   un espace libre pour l’air ;
   un habillage ;
   une ouverture ;
   une trappe de nettoyage et de visite ;
   une entretoise ;
   une armature.
Le conduit système air / fumée englobe un ensemble d'éléments compatibles, fournis ou conseillés par un fabricant assumant la responsabilité du produit pour le conduit de fumée dans son intégralité.

Dimniki - Sistemski dimniki s keramičnimi tuljavami - 3. del: Zahteve in preskusne metode za dimnike z zračnimi kanali

General Information

Status
Published
Publication Date
17-Jul-2007
ICS
91.060.40 - Chimneys, shafts, ducts
Technical Committee
CEN/TC 166 - Chimneys
Drafting Committee
CEN/TC 166/WG 6 - Clay/Ceramic and Concrete chimneys components
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
06-May-2021
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/105 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on chimneys, flues and specific products
Ref Project
SIST EN 13063-3:2008 - Chimneys — System chimneys with clay/ceramic flue liners — Part 3: Requirements and test methods for air flue system chimneys

Buy Standard

EN 13063-3:2008EN 13063-3:2008
PreviousNext
Standard
EN 13063-3:2008
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Chimneys — System chimneys with clay/ceramic flue liners — Part 3: Requirements and test methods for air flue system chimneysConduits de fumées - Conduits-systemes avec conduit intérieur en terre cuite/céramique - Partie 3 : Exigences et méthodes d'essai pour conduits-systemes a brassage d'airAbgasanlagen - System-Abgasanlagen mit Keramik-Innenrohren - Teil 3: Anforderungen und Prüfungen für Luft-AbgasleitungenTa slovenski standard je istoveten z:EN 13063-3:2007SIST EN 13063-3:2008en,fr91.060.40ICS:SLOVENSKI
STANDARDSIST EN 13063-3:200801-marec-2008

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13063-3July 2007ICS 91.060.40 English VersionChimneys - System chimneys with clay/ceramic flue liners - Part3: Requirements and test methods for air flue system chimneysConduits de fumées - Conduits-systèmes avec conduitintérieur en terre cuite/céramique - Partie 3 : Exigences etméthodes d'essai pour conduits-systèmes à brassage d'airAbgasanlagen - System-Abgasanlagen mit Keramik-Innenrohren - Teil 3: Anforderungen und Prüfungen für Luft-AbgasleitungenThis European Standard was approved by CEN on 9 June 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13063-3:2007: E

Test methods.16 A.1 Compressive strength of pressure-equalising opening sections.16 A.1.1 Test sample.16 A.1.2 Testing equipment.16 A.1.3 Test procedure.16 A.2 Aerodynamic behaviour of terminals under wind conditions.16 A.2.1 Test apparatus.16 A.2.2 Test sample.16 A.2.3 Measuring parameters.16 A.2.4 Test procedure.17 A.2.5 Test results.17 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Directive.18 ZA.1 Scope and relevant characteristics.18

CE marking and labelling.23 Bibliography.27

This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 89/106.
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Key 1 Flue duct 2 Insulation layer 3 Outer wall 4 Cavities for structural reinforcement 5 Air gap Figure 1 — Examples of cross sections of concentric air flue system chimneys

Key 1 Flue duct 2 Insulation layer or air gap 3 Outer wall 4 Cavities for structural reinf
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15287-2:2023(Main)
Chimneys - Design, installation and commissioning - Part 2: Chimneys and connecting flue pipes for room sealed combustion appliances
SIST EN 15287-2:2023

This document describes the method of specifying the design, installation and labelling criteria for chimney systems, construction of custom-built chimneys, the relining or converting of existing chimneys, connecting flue pipes and air supply pipes for room sealed combustion appliances as well as the use of chimney products. It also gives information on commissioning of an installed chimney.
This document applies to chimneys which are subject to the following limiting conditions:
-   the distance between the supports not to exceed 4 m;
-   the distance above the last structural attachment not to exceed 3 m;
-   the free-standing height above the uppermost structural support attachment for chimneys with rectangular cross section is not more than five times the smallest external dimension.
This document does not cover:
-   chimneys which serve a mixture of fan assisted or forced draught burners or natural draught appliances,
-   installations having a configuration of the type C2.
NOTE   Room sealed gas appliances are classified as type C according to EN 1749.
The methods in this part of this document are applicable to chimneys and connecting flue pipes for room sealed combustion appliances. The methods in Part 1 of this document are applicable to chimneys and connecting flue pipes for non-room sealed combustion appliances.

  • Standard
    108 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15287-1:2023(Main)
Chimneys - Design, installation and commissioning - Part 1: Chimneys and connecting flue pipes for non-room sealed combustion appliances
SIST EN 15287-1:2023

This document describes the method of specifying the design, installation and labelling criteria for system chimneys, construction of custom-built chimneys, the relining of existing chimneys and connecting flue pipes for non-room sealed combustion appliances as well as the use of chimney products. It also gives information on commissioning of an installed chimney.
This document applies to chimneys which are subject to the following limiting conditions:
-   the distance between the supports not to exceed 4 m;
-   the distance above the last structural attachment not to exceed 3 m;
-   the free-standing height above the uppermost structural support attachment for chimneys with rectangular cross section is not more than five times the smallest external dimension.
The methods in this part of this document are applicable to chimneys and connecting flue pipes for non-room sealed combustion appliances. The methods in Part 2 of this document are applicable to chimneys and connecting flue pipes for room sealed combustion appliances.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16475-7:2016+A1:2020(Main)
Chimneys - Accessories - Part 7: Rain caps - Requirements and test methods
SIST EN 16475-7:2016+A1:2020

This European Standard specifies requirements and test methods for rain caps that are used as components, subject to flue gas, in order to prevent rain entry into the chimneys. Rain caps already tested together with system chimney products or other chimney components, e.g. terminals, are not covered by this standard. Rain caps incorporating a bird guard are also included. It also specifies the requirements for marking, manufacturers’ instruction, product information and evaluation of conformity.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16475-4:2020(Main)
Chimneys - Accessories - Part 4: Flue dampers - Requirements and test methods
SIST EN 16475-4:2020

This document specifies the characteristics and test methods for flue dampers that are used as components, carrying flue gas, in order to limit the flow in a chimney or to prevent back flow of soot during cleaning of the chimney or to prevent the backflow of the flue gas e.g. in case of multi-served chimneys.
This document covers only flue dampers incorporated in a housing and installed inside a building.
This document covers only flue dampers with sealings made of elastomeric materials for temperature classes up to T 200 and corrosion class 1 or 2 in accordance with EN 14241-1 or sealing materials for dry applications with a fire reaction class A1 in accordance with EN 13501-1.
This document covers only flue dampers with motor drive, casing and flue damper plate which are interlocked in such a way that they can only be separated by using tools.
This document covers only mechanical flue dampers where any motor is in accordance with EN 60730-2-14 and the cover for electrical components of the flue damper fulfils minimum protection class IP40 according to EN 60529.
This document covers only flue dampers which are designed and installed to ensure that incorrect information about the position of the flue damper flap are absolutely impossible, which are only installed on components that are interlocked to the casing, which are only activated by components that are interlocked to the flue damper flap and where it is ensured that the limit switch opens or the flue damper flap moves to the open position if one of these interlocks fails. This safety target may also be achieved with an equally suitable method (e.g. bracing or welding).
This document covers only flue dampers for biomass boilers ≥ 1 000 kW and industrial applications with limit switches in accordance with EN 61058-1 or EN 50156-1.
This document covers only flue dampers where it is possible to identify the position of the flue damper flap.
This document covers only totally closed, manually driven flue dampers (type 1) which have a facility to adjust the position of the flue damper flap.
This document covers only totally closed, mechanically driven flue dampers (type 2) with only the positions "fully opened" and "fully closed" and where it is not possible to fix the flap in the non-closed position during the flue damper flap stays in closed position while the appliance is not working.
NOTE   This applies only to multi-appliance installations with positive pressure conditions.
This document covers only partially closed flue dampers (type 3 to 5) where it is possible to adjust the position of the flue damper flap and where it is ensured that the flue damper flap does not change position by itself.
Flue dampers which are integral parts of system chimney products or other chimney components, e.g. flue liners, connecting flue pipes, are not covered by this document.
This document also specifies the provisions for marking, manufacturers’ instruction, product information, Assessment and Verification of Constancy of Performance (AVCP).
This document does not specify issues for electrical parts.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16475-6:2020(Main)
Chimneys - Accessories - Part 6: Access components - Requirements and test methods
SIST EN 16475-6:2020

This document specifies the requirements and test methods for access components comprising a frame and a door or doors which provide access to the flue of a chimney for the purpose of inspection or cleaning.
Access components for higher nominal working temperature than 450 °C, positive pressure and wet applications are not covered by this standard.
The document is limited to access components with door opening dimensions with a maximum width of 450 mm and a maximum height of 600 mm.
Products not freely ventilated are excluded from this document.
This document also specifies the requirements for marking, manufacturers’ instruction, product information and information on the AVCP (Assessment and Verification of Constancy of Performance).
Access components already tested together with system chimney products or other chimney components, e.g. flue liners, are not covered by this document.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16475-1:2020(Main)
Chimneys - Accessories - Part 1: Chimney silencers - Requirements and test methods
SIST EN 16475-1:2020

This European Standard specifies requirements and test methods for flue gas silencers made of metal that are used as accessories in order to reduce the noise level of combustions appliances.
The standard covers silencers in the connecting flue pipes and on top of chimneys.
This standard does not cover silencers installed as chimney sections. This standard excludes active silencers.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13384-1:2015+A1:2019(Main)
Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one combustion appliance
SIST EN 13384-1:2015+A1:2019

This European Standard specifies methods for the calculation of the thermal and fluid dynamic characteristics of chimneys serving one heating appliance.
The methods in this part of this European Standard are applicable to negative or positive pressure chimneys with wet or dry operating conditions. It is valid for chimneys with heating appliances for fuels subject to the knowledge of the flue gas characteristics which are needed for the calculation.
The methods in this part of this European Standard are applicable to chimneys with one inlet connected with one appliance. The methods in Part 2 of this European Standard are applicable to chimneys with multiple inlets and one inlet with multiple appliances. Part 3 describes methods for the development of diagrams and tables for chimneys serving one heating appliance.

  • Standard
    105 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13384-2:2015+A1:2019(Main)
Chimneys - Thermal and fluid dynamic calculation methods - Part 2: Chimneys serving more than one combustion appliance
SIST EN 13384-2:2015+A1:2019

This part of EN 13384 specifies methods for calculation of the thermal and fluid dynamic characteristics of chimneys serving more than one heating appliance.
This part of EN 13384 covers both the cases, either
a)   where the chimney is connected with more than one connecting flue pipe from individual or several appliances in a multi-inlet arrangement; or
b)   where the chimney is connected with an individual connecting flue pipe connecting more than one appliance in a cascade arrangement.
The case of multiple inlet cascade arrangement is covered by the case a).
This part of EN 13384 deals with chimneys operating under negative pressure conditions (there can be positive pressure condition in the connecting flue pipe) and with chimneys operating under positive pressure conditions and is valid for chimneys serving heating appliances for liquid, gaseous and solid fuels.
This part of EN 13384 does not apply to:
-   chimneys with different thermal resistance or different cross-section in the various chimney segments. This part does not apply to calculate energy gain;
-   chimneys with open fire places, e.g. open fire chimneys or chimney inlets which are normally intended to operate open to the room;
-   chimneys which serve different kinds of heating appliances regarding natural draught, fan assisted, forced draught or combustion engine. Fan assisted appliances with draught diverter between the fan and the chimney are considered as natural draught appliances;
-   chimneys with multiple inlets from more than 5 storeys. (This does not apply to balanced flue chimney.);
-   chimneys serving heating appliances with open air supply through ventilation openings or air ducts, which are not installed in the same air supply pressure region (e.g. same side of building).
For positive pressure chimneys this part only applies if any heating appliance which is out of action can be positively isolated to prevent flue gas back flow.

  • Standard
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1443:2019(Main)
Chimneys - General requirements
SIST EN 1443:2019

This document specifies requirements and the basic performance criteria for chimneys, flue liners, connecting flue pipes, components and accessories used to convey the products of combustion from combustion appliances to the outside atmosphere. This document is to be used as a reference for all product standards of CEN/TC 166.
This document specifies sootfire resistant chimneys, flue liners, connecting flue pipes, fittings and accessories for combustion appliances burning solid, liquid and gaseous fuels and non-sootfire resistant chimneys, flue liners, connecting flue pipes, components and accessories for combustion appliances burning liquid and gaseous fuels only. It also specifies sootfire safe accessories for combustion appliances burning solid, liquid and gaseous fuels.
NOTE 1   This means that chimneys, flue liners, connecting flue pipes and components which are non-sootfire resistant and accessories which are non-sootfire resistant or non-sootfire safe are not suitable for combustion appliances burning solid fuel.
This document also identifies minimum requirements for marking, instructions, product information and provides guidance for the assessment and verification of constancy of performance (AVCP).
This document does not apply to structurally independent chimneys and custom-built chimneys consisting of non-CE-marked components.
NOTE 2   This document can be used as a basis for the specifications of products covered by a European Technical Assessment.
NOTE 3   All product standards drafted by Technical Committee CEN/TC 166 are based on the Mandate M/105.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    42 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13216-1:2019(Main)
Chimneys - Test methods for system chimneys - Part 1: General test methods
SIST EN 13216-1:2019

This document specifies material-independent general test methods for all system chimneys. It can be used for all flue gas carrying products.
NOTE   The thermal performance tests for the determination of the distance to combustible material for accessories (draught regulators, access components, etc.) are included in different standards of CEN/TC 166.

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day