Chimneys - Accessories - Part 6: Access components - Requirements and test methods

This document specifies the requirements and test methods for access components comprising a frame and a door or doors which provide access to the flue of a chimney for the purpose of inspection or cleaning.
Access components for higher nominal working temperature than 450 °C, positive pressure and wet applications are not covered by this standard.
The document is limited to access components with door opening dimensions with a maximum width of 450 mm and a maximum height of 600 mm.
Products not freely ventilated are excluded from this document.
This document also specifies the requirements for marking, manufacturers’ instruction, product information and information on the AVCP (Assessment and Verification of Constancy of Performance).
Access components already tested together with system chimney products or other chimney components, e.g. flue liners, are not covered by this document.

Abgasanlagen - Zubehörteile - Teil 6: Zugangsbauteile - Anforderungen und Prüfverfahren

Dieses Dokument legt die Anforderungen und Prüfverfahren für Zugangsbauteile mit einem Rahmen und einem Verschluss oder Verschlüssen fest, die dazu dienen, den Abgasweg einer Abgasanlage zur Inspektion oder Reinigung zugänglich zu machen.
Zugangsbauteile für Nennbetriebstemperaturen größer 450 °C, für Überdruck und für feuchte Betriebsweise fallen nicht in den Anwendungsbereich dieser Norm.
Dieses Dokument ist auf Zugangsbauteile mit Öffnungsquerschnitten des Verschlusses von höchstens 450 mm in der Breite und höchstens 600 mm in der Höhe beschränkt.
Nicht frei belüftete Produkte sind von diesem Dokument ausgeschlossen.
Diese Norm legt außerdem die Anforderungen an die Kennzeichnung, Herstelleranweisungen, Produktinformationen und Informationen zur Bewertung und Überprüfung der Leistungsbeständigkeit (en: AVCP) fest.
Zugangsbauteile, die bereits zusammen mit Produkten für System-Abgasanlagen oder mit anderen Bauteilen einer Abgasanlage, z. B. Innenrohre, geprüft worden sind, fallen nicht in den Anwendungsbereich dieses Dokuments.

Conduits de cheminée - Accessoires - Partie 6 : Éléments d'accès - Exigences et méthodes d'essai

Le présent document spécifie les exigences et les méthodes d'essai pour les éléments d'accès comprenant un cadre et une ou plusieurs portes permettant d'accéder au conduit de fumée en vue de son inspection ou de son nettoyage.
Les éléments d'accès pour une température nominale de fonctionnement supérieure à 450 °C, une pression positive et pour des installations en conditions humides ne sont pas traités dans la présente norme.
Le présent document se limite aux éléments d'accès avec une ouverture de porte d'une largeur maximale de 450 mm et d'une hauteur maximale de 600 mm.
Les produits qui ne sont pas ventilés librement sont exclus du présent document.
Le présent document spécifie également les exigences relatives au marquage, aux instructions du fabricant, aux informations produit et aux informations concernant l'EVCP (Évaluation et vérification de la constance des performances).
Les éléments d'accès déjà soumis à essai en même temps que les conduits système ou d'autres composants de conduits de fumée (par exemple, des tubages) ne relèvent pas du domaine d'application du présent document.

Dimovodne naprave - Oprema - 6. del: Čistilne odprtine - Zahteve in preskusne metode

General Information

Status
Published
Publication Date
07-Apr-2020
Withdrawal Date
30-Jan-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
08-Apr-2020
Due Date
19-Apr-2018
Completion Date
08-Apr-2020

Buy Standard

Standard
EN 16475-6:2020
English language
33 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-junij-2020
Dimovodne naprave - Oprema - 6. del: Čistilne odprtine - Zahteve in preskusne
metode
Chimneys - Accessories - Part 6: Access components - Requirements and test methods
Abgasanlagen - Zubehörteile - Teil 6: Zugangsbauteile - Anforderungen und
Prüfverfahren
Conduits de cheminée - Accessoires - Partie 6 : Éléments d'accès - Exigences et
méthodes d'essai
Ta slovenski standard je istoveten z: EN 16475-6:2020
ICS:
91.060.40 Dimniki, jaški, kanali Chimneys, shafts, ducts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 16475-6
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2020
EUROPÄISCHE NORM
ICS 91.060.40
English Version
Chimneys - Accessories - Part 6: Access components -
Requirements and test methods
Conduits de cheminée - Accessoires - Partie 6 : Abgasanlagen - Zubehörteile - Teil 6: Zugangsbauteile -
Éléments d'accès - Exigences et méthodes d'essai Anforderungen und Prüfverfahren
This European Standard was approved by CEN on 25 December 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16475-6:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Product characteristics . 6
4.1 General . 6
4.2 Mechanical resistance and stability . 6
4.2.1 Freedom of movement of the door . 6
4.2.2 Impact resistance of the door . 6
4.2.3 Inner door security . 6
4.3 Thermal performance . 6
4.3.1 Reaction to fire . 6
4.3.2 Resistance to fire (internal to external) . 7
4.4 Hygiene, health and environment . 7
4.4.1 Gas tightness . 7
4.4.2 Condensate resistance . 7
4.4.3 Corrosion resistance . 7
4.4.4 Dangerous substances . 8
4.5 Thermal resistance . 8
4.6 Materials . 8
4.6.1 Access components in contact with combustion products . 8
4.6.2 Additional information on other materials of construction . 8
4.6.3 Freeze/thaw resistance . 8
4.7 Operational requirements . 9
4.7.1 Handling . 9
4.7.2 Angle of opening . 9
4.7.3 Closing mechanism . 9
4.7.4 Space for additional information . 9
5 Testing, assessment and sampling methods . 9
5.1 Manufacturer's declaration for type test . 9
5.2 Mechanical resistance and stability . 9
5.2.1 Free movement test . 9
5.2.2 Swing ball test . 10
5.3 Thermal performance tests . 12
5.3.1 General . 12
5.3.2 Test Assembly . 12
5.3.3 Test procedure . 14
5.4 Gas tightness . 14
5.4.1 Test assembly . 14
5.4.2 Test Procedure . 15
5.4.3 Test results . 15
5.5 Test sequence . 15
6 Assessment and verification of constancy of performance – AVCP. 15
6.1 General . 15
6.2 Type testing . 16
6.2.1 General . 16
6.2.2 Test samples, testing and compliance criteria . 16
6.2.3 Test reports . 17
6.2.4 Shared other party results . 17
6.2.5 Cascading determination of the product type results . 18
6.3 Factory production control (FPC) . 19
6.3.1 General . 19
6.3.2 Requirements . 20
6.3.3 Product specific requirements . 22
6.3.4 Initial inspection of factory and of FPC . 22
6.3.5 Continuous surveillance of FPC . 23
6.3.6 Procedure for modifications . 23
6.3.7 One-off components, pre-production products (e.g. prototypes) and components
produced in very low quantity . 23
7 Classification and designation . 24
7.1 General . 24
7.2 Temperature classes and test temperature . 25
7.3 Gas tightness class . 25
7.4 Condensate resistance class . 25
7.5 Corrosion resistance. 25
7.6 Soot fire resistance and distance to combustible material . 25
8 Marking, labelling and packaging . 25
8.1 Access component . 25
8.2 Packaging . 26
8.3 Product information – Manufacturer’s instructions . 26
Annex A (normative) Choice of size for type test and sampling . 27
Annex B (normative) Sampling for factory productions control . 28
B.1 Sampling plans . 28
B.2 Inspection levels and procedures . 28
Annex C (normative) Factory production control . 30
C.1 General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.