EN ISO 24490:2016
(Main)Cryogenic vessels - Pumps for cryogenic service (ISO 24490:2016)
Cryogenic vessels - Pumps for cryogenic service (ISO 24490:2016)
ISO 24490:2016 specifies the minimum requirements for the design, manufacture and testing of pumps for cryogenic service.
ISO 24490:2016 is applicable to centrifugal pumps. However, it can be applied to other types of cryogenic pumps (e.g. reciprocating pumps), where applicable.
This International Standard also gives guidance on the design of installations (see Annex A).
It does not specify requirements for operation or maintenance.
NOTE For cryogenic fluids, see ISO 21029‑1, ISO 20421‑1 and/or ISO 21009‑1.
Kryo-Behälter - Pumpen für den Kryo-Betrieb (ISO 24490:2016)
Diese Internationale Norm legt die Mindestanforderungen für die Auslegung, die Fertigung, und die Prüfung von Pumpen für den Kryo Betrieb fest.
Diese Internationale Norm gilt für Kreiselpumpen. Sie kann jedoch, sofern zutreffend, auch für andere Pumpenbauarten (z. B. Kolbenpumpen) angewendet werden.
Diese Internationale Norm enthält auch Anleitungen zur Auslegung von Anlagen (siehe Anhang A).
Sie legt keine Anforderungen an Betrieb oder Instandhaltung fest.
Récipients cryogéniques - Pompes pour service cryogénique (ISO 24490:2016)
ISO 24490:2016 spécifie les exigences minimales en matière de conception, de fabrication et d'essais des pompes pour service cryogénique.
ISO 24490:2016 s'applique aux pompes centrifuges. Le cas échéant, elle peut toutefois être appliquée à d'autres types de pompes cryogéniques (pompes à piston, par exemple).
La présente Norme internationale donne également des préconisations pour la conception des installations (voir l'Annexe A).
Elle ne spécifie aucune exigence relative au fonctionnement ou à la maintenance.
NOTE Pour les fluides cryogéniques, voir l'ISO 21029‑1, l'ISO 20421‑1 et/ou l'ISO 21009‑1.
Kriogene posode - Črpalke za kriogeno področje (ISO 24490:2016)
Ta standard določa minimalne zahteve za načrtovanje, izdelavo in preskušanje črpalk za kriogeno področje (t.j. za delo s kriogenimi tekočinami pod –10 °C). Ta standard zajema centrifugalne črpalke. Načela iz tega standarda se lahko uporabijo za druge vrste črpalk (npr. batne črpalke). Ta standard podaja tudi smernice glede načrtovanja objektov (glej dodatek A). Standard ne določa zahtev za obratovanje ali vzdrževanje.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 24490:2017
01-maj-2017
1DGRPHãþD
SIST EN 13275:2001
.ULRJHQHSRVRGHýUSDONH]DNULRJHQRSRGURþMH ,62
Cryogenic vessels - Pumps for cryogenic service (ISO 24490:2016)
Kryo-Behälter - Pumpen für den Kryo-Betrieb (ISO 24490:2016)
Récipients cryogéniques - Pompes pour service cryogénique (ISO 24490:2016)
Ta slovenski standard je istoveten z: EN ISO 24490:2016
ICS:
23.020.40 Proti mrazu odporne posode Cryogenic vessels
(kriogenske posode)
23.080 ýUSDONH Pumps
SIST EN ISO 24490:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 24490:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 24490:2017
EN ISO 24490
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2016
EUROPÄISCHE NORM
ICS 23.020.40 Supersedes EN 13275:2000
English Version
Cryogenic vessels - Pumps for cryogenic service (ISO
24490:2016)
Récipients cryogéniques - Pompes pour service Kryo-Behälter - Pumpen für den Kryo-Betrieb (ISO
cryogénique (ISO 24490:2016) 24490:2016)
This European Standard was approved by CEN on 15 March 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24490:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24490:2017
EN ISO 24490:2016 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 24490:2017
EN ISO 24490:2016 (E)
European foreword
This document (EN ISO 24490:2016) has been prepared by Technical Committee
ISO/TC 220 “Cryogenic vessels” in collaboration with Technical Committee CEN/TC 268 “Cryogenic
vessels and specific hydrogen technologies applications” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2016, and conflicting national standards shall
be withdrawn at the latest by October 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 13275:2000.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 24490:2016 has been approved by CEN as EN ISO 24490:2016 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 24490:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 24490:2017
INTERNATIONAL ISO
STANDARD 24490
Second edition
2016-03-15
Cryogenic vessels — Pumps for
cryogenic service
Récipients cryogéniques — Pompes pour service cryogénique
Reference number
ISO 24490:2016(E)
©
ISO 2
...
SLOVENSKI STANDARD
oSIST prEN ISO 24490:2015
01-maj-2015
.ULRJHQHSRVRGHýUSDONH]DNULRJHQRSRGURþMH ,62',6
Cryogenic vessels - Pumps for cryogenic service (ISO/DIS 24490:2015)
Kryo-Behälter - Pumpen für den Kryo-Betrieb (ISO/DIS 24490:2015)
Récipients cryogéniques - Pompes pour service cryogénique (ISO/DIS 24490:2015)
Ta slovenski standard je istoveten z: prEN ISO 24490
ICS:
23.020.40 Proti mrazu odporne posode Cryogenic vessels
(kriogenske posode)
23.080 ýUSDONH Pumps
oSIST prEN ISO 24490:2015 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 24490:2015
---------------------- Page: 2 ----------------------
oSIST prEN ISO 24490:2015
DRAFT INTERNATIONAL STANDARD
ISO/DIS 24490
ISO/TC 220 Secretariat: AFNOR
Voting begins on: Voting terminates on:
2015-02-12 2015-05-12
Cryogenic vessels — Pumps for cryogenic service
Récipients cryogéniques — Pompes pour service cryogénique
ICS: 23.020.40
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24490:2014(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2014
---------------------- Page: 3 ----------------------
oSIST prEN ISO 24490:2015
ISO/DIS 24490:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 24490:2015
ISO/DIS 24490
Contents Page
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements for pumps . 2
4.1 General . 2
4.2 Materials . 2
4.2.1 General . 2
4.2.2 Mechanical properties at low temperature . 3
4.2.3 Corrosion resistance . 3
4.2.4 Oxygen compatibility .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.