Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners (ISO 11148-6:2010)

ISO 11148-6:2010 applies to hand-held non-electric power tools (hereafter referred to as “assembly power tools for threaded fasteners”) intended for tightening or installing of threaded fasteners. The assembly power tools for threaded fasteners can be powered by compressed air, hydraulic fluid or internal combustion engines and are intended for use by one operator and supported by the operator's hand or hands, with or without a suspension, e.g. a balancer.
ISO 11148-6:2010 covers air-hydraulic impulse wrenches, impact wrenches, fastener installation tools, nutrunners, open-ended spanners (crow-foot with open-ended socket or tube nut wrench), ratchet wrenches and screwdrivers.
ISO 11148-6:2010 does not cover special requirements and modifications of assembly power tools for threaded fasteners for the purpose of mounting them in fixtures.
ISO 11148-6:2010 deals with all significant hazards, hazardous situations or hazardous events when the tools are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of assembly power tools for threaded fasteners in potentially explosive atmospheres.

Handgehaltene nicht elektrisch betriebene Maschinen - Sicherheitsanforderungen - Teil 6: Maschinen für Schraubverbindungen (ISO 11148-6:2010)

Der vorliegende Teil von ISO 11148 gilt für handgehaltene nicht elektrisch betriebene Maschinen (im
Folgenden als „Maschinen für Schraubverbindungen“ bezeichnet), zum Anziehen oder Einsetzen von
Befestigungselementen mit Gewinde. Die Maschinen für Schraubverbindungen können von Druckluft,
Hydraulikflüssigkeit oder einem Verbrennungsmotor angetrieben werden, sind zum Gebrauch durch einen
einzelnen Bediener vorgesehen und werden vom Bediener in seiner Hand oder seinen Händen gehalten, mit
oder ohne eine Aufhängung, z. B. eine Ausgleichseinrichtung.
Der vorliegende Teil von ISO 11148 ist anwendbar auf:
⎯ luft-hydraulische Schlagschrauber;
⎯ Schlagschrauber;
⎯ Maschinen zur Installation von Befestigungselementen;
⎯ Mutterndreher;
⎯ Winkelschrauber mit offenem Flachkopf (Flachkopfschrauber mit offener Fassung oder Rohrmutterschrauber);
⎯ Ratschenschrauber;
⎯ Schraubendreher.
ANMERKUNG 1 Anhang B enthält Beispiele für Maschinen für Schraubverbindungen.
Der vorliegende Teil von ISO 11148 gilt nicht für die besonderen Anforderungen und Änderungen an
Maschinen für Schraubverbindungen zum Zwecke des Spannens in eine Halterung.
Der vorliegende Teil von ISO 11148 behandelt alle signifikanten Gefährdungen, gefährliche Situationen oder
Ereignisse, die beim vorgesehenen Gebrauch von Maschinen sowie unter Bedingungen vom Hersteller vorhersehbaren
Missbrauchs auftreten können; ausgenommen die Verwendung von Maschinen für Schraubverbindungen
in explosionsgefährdeten Atmosphären.
ANMERKUNG 2 EN 13463-1 enthält Anforderungen an nicht elektrisch betriebene Geräte für den Einsatz in explosionsgefährdeten
Atmosphären.

Machines portatives à moteur non électrique - Exigences de sécurité - Partie 6: Machines d'assemblage pour éléments de fixation filetés (ISO 11148-6:2010)

L'ISO 11148-6:2010 s'applique aux machines portatives non électriques (appelées dans le reste du texte «machine portative d'assemblage pour éléments de fixation filetés» ou «machine portative d'assemblage») utilisées pour le serrage ou la mise en place d'éléments de fixation filetés. Les machines portatives d'assemblage pour éléments de fixation filetés peuvent être alimentées par air comprimé, fluide hydraulique ou moteurs à combustion interne et sont prévues pour être utilisées par un opérateur ou portées par la ou les mains de l'opérateur avec ou sans suspension, par exemple à l'aide d'un équilibreur.
L'ISO 11148-6:2010 couvre les clés à impulsion hydropneumatiques, les clés à choc, les machines pour mise en place d'éléments de fixation, les serreuses, les serreuses à renvoi d'axe avec une noix de serrage ouverte, les clés à rochet et les visseuses.
L'ISO 11148-6:2010 ne couvre pas les exigences spécifiques et les modifications des machines portatives d'assemblage pour éléments de fixation filetés destinées à être montées sur un châssis.
L'ISO 11148-6:2010 traite de tous les phénomènes dangereux, situations dangereuses ou événements dangereux significatifs, à l'exception des machines portatives d'assemblage pour éléments de fixation filetés destinées à être utilisées dans une atmosphère potentiellement explosible, lorsqu'elles sont utilisées normalement et lorsqu'elles font l'objet d'un mauvais usage raisonnablement prévisible par le fabricant.

Neelektrična ročna orodja - Varnostne zahteve - 6. del: Orodja za vijačne zveze (ISO 11148-6:2010)

Ta standard velja za neelektrična ročna orodja, gnana z rotacijskimi ali linearnimi motorji, ki so gnani na stisnjen zrak, s hidravlično tekočino ali z motorji z notranjim zgorevanjem, in so namenjena uporabi operaterja in so podprta z: - roko ali rokami operaterja ali obešala, npr. balanserja; - ročnimi orodji, ki jih je mogoče pritrditi.

General Information

Status
Withdrawn
Publication Date
30-Sep-2010
Withdrawal Date
18-Dec-2012
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
19-Dec-2012
Completion Date
19-Dec-2012

Relations

Buy Standard

Standard
EN ISO 11148-6:2011 - BARVE
English language
41 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-junij-2011
1DGRPHãþD
SIST EN 792-6:2000+A1:2008
1HHOHNWULþQDURþQDRURGMD9DUQRVWQH]DKWHYHGHO2URGMD]DYLMDþQH]YH]H
,62
Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools
for threaded fasteners (ISO 11148-6:2010)
Handgehaltene nichtelektrisch betriebene Maschinen - Sicherheitsanforderungen -Teil 6:
Maschinen für Schraubverbindungen (ISO 11148-6:2010)
Machines portatives à moteur non électrique - Exigences de sécurité - Partie 6:
Machines portatives d'assemblage pour éléments de fixation filetés (ISO 11148-6:2010)
Ta slovenski standard je istoveten z: EN ISO 11148-6:2010
ICS:
25.140.10 3QHYPDWLþQDRURGMD Pneumatic tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11148-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2010
ICS 25.140.10 Supersedes EN 792-6:2000+A1:2008
English Version
Hand-held non-electric power tools - Safety requirements - Part
6: Assembly power tools for threaded fasteners (ISO 11148-
6:2010)
Machines portatives à moteur non électrique - Exigences Handgehaltene nicht elektrisch betriebene Maschinen -
de sécurité - Partie 6: Machines d'assemblage pour Sicherheitsanforderungen - Teil 6: Maschinen für
éléments de fixation filetés (ISO 11148-6:2010) Schraubverbindungen (ISO 11148-6:2010)
This European Standard was approved by CEN on 30 September 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11148-6:2010: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .4

Foreword
This document (EN ISO 11148-6:2010) has been prepared by Technical Committee ISO/TC 118
"Compressors and pneumatic tools, machines and equipment" in collaboration with Technical Committee
CEN/TC 255 “Hand-held, non-electric power tools - Safety” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2011, and conflicting national standards shall be withdrawn at the
latest by April 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 792-6:2000+A1:2008.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11148-6:2010 has been approved by CEN as a EN ISO 11148-6:2010 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC on machinery.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the clauses of this
standard confers, within the limits of the scope of this standard, a presumption of conformity with the
corresponding Essential Requirements of that Directive except ER 1.5.7 and associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.

INTERNATIONAL ISO
STANDARD 11148-6
First edition
2010-10-01
Hand-held non-electric power tools —
Safety requirements —
Part 6:
Assembly power tools for threaded
fasteners
Machines portatives à moteur non électrique — Exigences de
sécurité —
Partie 6: Machines d'assemblage pour éléments de fixation filetés

Reference number
ISO 11148-6:2010(E)
©
ISO 2010
ISO 11148-6:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved

ISO 11148-6:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.2
3 Terms and definitions .2
3.1 General definitions .2
3.2 Definitions related to assembly power tools for threaded fasteners.4
4 Safety requirements and/or protective measures.5
4.1 General .5
4.2 Mechanical safety.5
4.3 Thermal safety .6
4.4 Noise.6
4.5 Vibration .7
4.6 Materials and substances processed, used or exhausted.7
4.7 Ergonomics.8
4.8 Controls.10
5 Verification .11
5.1 General conditions for tests.11
5.2 Noise.11
5.3 Vibration .11
5.4 Unintentional start.11
5.5 Power tool construction .11
5.6 Structure of verification of safety requirements .12
6 Information for use.13
6.1 Marking, signs and written warnings .13
6.2 Instruction handbook.13
6.3 Operating instructions.19
6.4 Data.19
6.5 Maintenance instructions .20
Annex A (informative) List of significant hazards .21
Annex B (informative) Examples of assembly power tools for threaded fasteners covered by this
part of ISO 11148 .23
Annex C (normative) Symbols for labels and signs.25
Annex D (normative) Additional safety requirements related to internal combustion engine power
tools .27
Bibliography.31

ISO 11148-6:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Stand
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.