iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1854:1997

(Main)

Pressure sensing devices for gas burners and gas burning appliances

Pressure sensing devices for gas burners and gas burning appliances

This European Standard specifies requirements and test methods for pressure sensing devices (referred to as psds) for the control of combustible gases of the first, second and third families, air, combustion products and mixtures there of for pressures up to 4 bar. It covers all types of psd including electronic, differential and inferential types.  The requirements for 'S' class psd are intended to meet the requirements for increased reliability for steam boilers.  The methods of test given in this standard are intended for product type testing. Tests intended for production testing are not specifically included.

Druckwächter für Gasbrenner und Gasgeräte

Diese Europäische Norm legt Anforderungen und Prüfverfahren an Druckwächter fest, welche bei Drücken bis 4 bar eingesetzt werden, um brennbare Gase der ersten, zweiten und dritten Gasfamilie, Luft, Verbrennungsprodukte und Gemischen davon, zu überwachen. Sie gilt für alle Arten von Druckwächtern einschließlich elektronischer Ausführungen sowie für Differenzdruckwächter und ähnliche Arten. Die Anforderungen an Druckwächter der Klasse "S" sind dafür vorgesehen, die erhöhten Anforderungen an die Zuverlässigkeit ("Besondere Bauart") zum Einsatz an Dampfkesseln zu erfüllen.

Dispositifs de surveillance de pression pour brûleurs à gaz et appareils à gaz

La présente norme européenne précise les spécifications de fonctionnement et les méthodes d'essai des dispositifs de surveillance de la pression des combustibles, des première, seconde et troisième familles, d'air, de gaz produits par la combustion et autres mélanges gazeux jusqu'à des pressions de 4 bar (dispositifs dénommés ci-après "pressostats"). Elle s'applique à tous les types de pressostats y compris électroniques, différentiels et inférentiels. Les exigences pour les pressostats de classe 'S' tendent à répondre aux exigences de fiabilité accrue pour les chaudières à vapeur.

Tlačna zaznavala za plinske gorilnike in plinske aparate

General Information

Status
Withdrawn
Publication Date
19-Aug-1997
Withdrawal Date
25-Apr-2006
ICS
23.060.40 - Pressure regulators
27.060.20 - Gas fuel burners
Technical Committee
CEN/TC 58 - Safety and control devices for burners and appliances burning gaseous or liquid fuels
Drafting Committee
CEN/TC 58/WG 7 - Gas/air pressure switches
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
26-Apr-2006
Completion Date
26-Apr-2006
Directive
2009/142/EC - DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 30 November 2009 relating to appliances burning gaseous fuels
90/396/EEC - Appliances burning gaseous fuels
Mandate
M/BC/CEN/89/6 - Standardization request to CEN concerning appliances burning gaseous fuels
Ref Project
SIST EN 1854:1997 - Pressure sensing devices for gas burners and gas burning appliances

Relations

Amended By
EN 1854:1997/A1:1998 - Pressure sensing devices for gas burners and gas burning appliances
Effective Date
22-Dec-2008
Replaced By
EN 1854:2006 - Pressure sensing devices for gas burners and gas burning appliances
Effective Date
22-Dec-2008

Buy Standard

EN 1854:1997EN 1854:1997
PreviousNext
Standard
EN 1854:1997
English language
32 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Druckwächter für Gasbrenner und GasgeräteDispositifs de surveillance de pression pour bruleurs a gaz et appareils a gazPressure sensing devices for gas burners and gas burning appliances27.060.20Plinski gorilnikiGas fuel burners23.060.40Pressure regulatorsICS:Ta slovenski standard je istoveten z:EN 1854:1997SIST EN 1854:1997en01-november-1997SIST EN 1854:1997SLOVENSKI
STANDARD



SIST EN 1854:1997



SIST EN 1854:1997



SIST EN 1854:1997



SIST EN 1854:1997



SIST EN 1854:19
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12067-2:2022(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Part 2: Fuel/air ratio control/supervision of the electronic type
SIST EN 12067-2:2023

EN 13611:2019, Clause 1 is replaced by the following:
This document specifies the safety, design, construction and performance requirements, and testing for electronic fuel/air ratio control systems (ERC), electronic fuel/air ratio supervision systems (ERS) and electronic fuel/air ratio trim systems (ERT) intended for use with burners and appliances burning gaseous or liquid fuels. It also describes the procedures for evaluating these requirements and specifies information necessary for installation and use.
This document is applicable to:
-   closed loop fuel/air ratio control systems, see 3.101;
-   fuel/air ratio supervision systems, see 3.102;
-   closed loop fuel/air ratio trim systems, see 3.103;
and does not differentiate into classification by heat input.
NOTE   The documents for burners, appliances or processes which use ERC, ERS or ERT can override the requirements of this document.

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12067-2 rev(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Part 2: Fuel/air ratio control / supervision of the electronic type
oSIST prEN 12067-2:2016

This European Standard specifies the safety, construction and performance requirements for electronic fuel/air ratio control (ERC), electronic fuel/air ratio supervision (ERS) and electronic fuel/air ratio trim (ERT) intended for use with burners and appliances burning gaseous or liquid fuels. It also describes the test procedures for evaluating these requirements and specifies information necessary for installation and use.
This standard is applicable to
-   closed loop fuel/air ratio controls (see 3.101),
-   fuel/air ratio supervision systems (see 3.102),
-   closed loop fuel/air ratio trim systems (see 3.103) and does not differentiate into classification by heat input.
This standard applies to ERC, ERS or ERT that can be tested independently, as well as part of an appliance or a burner.
NOTE 1 European Standards for burners, appliances or processes which use ERC, ERS or ERT can override the requirements of this standard.
NOTE 2 Provisions for production control are not part of this European Standard.

  • Draft
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12067-2:2022(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Part 2: Fuel/air ratio control/supervision of the electronic type
SIST EN 12067-2:2023

EN 13611:2019, Clause 1 is replaced by the following:
This document specifies the safety, design, construction and performance requirements, and testing for electronic fuel/air ratio control systems (ERC), electronic fuel/air ratio supervision systems (ERS) and electronic fuel/air ratio trim systems (ERT) intended for use with burners and appliances burning gaseous or liquid fuels. It also describes the procedures for evaluating these requirements and specifies information necessary for installation and use.
This document is applicable to:
-   closed loop fuel/air ratio control systems, see 3.101;
-   fuel/air ratio supervision systems, see 3.102;
-   closed loop fuel/air ratio trim systems, see 3.103;
and does not differentiate into classification by heat input.
NOTE   The documents for burners, appliances or processes which use ERC, ERS or ERT can override the requirements of this document.

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12186:2014(Main)
Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements
SIST EN 12186:2015

This European Standard contains the relevant functional requirements for gas pressure regulating stations, which form part of gas transmission or distribution systems. It is applicable to the design, materials, construction, testing, operation and maintenance of gas pressure regulating stations.
This European Standard does not apply to gas pressure regulating stations commissioned prior to the publication of this standard.
The stations covered by this European Standard have a maximum upstream operating pressure which does not exceed 100 bar. For higher maximum upstream operating pressures this standard should be used as a guideline.
If the inlet pipework of the station is a service line and the maximum upstream operating pressure does not exceed 16 bar and the design flow rate is equal to or less than 200 m3/h under normal conditions, EN 12279 applies.
Basic system requirements for gas pressure regulating stations are contained in this European Standard. Requirements for individual components (valves, regulators, safety devices, pipes, etc.) or installation of the components are contained in the appropriate European Standards.
NOTE   For combined regulating and measuring stations, the additional requirements of EN 1776 can apply.
The requirements in this European Standard do not apply to the design and construction of auxiliary facilities such as sampling, calorimetering, odorization systems and density measuring. These facilities are covered by the appropriate European Standards, where existing, or other relevant standards.
The requirements of this European Standard are based on good gas engineering practice under conditions normally encountered in the gas industry. Requirements for unusual conditions cannot be specifically provided for, nor are all engineering and construction details prescribed.
The requirements in this European Standard are based on the physical and chemical data of gaseous fuels – including non-conventional gases – in accordance with Table 1 of EN 437:2003+A1:2009 for first and second family gases. Additional requirements in the case of gaseous fuels heavier than air and/or sour gases are not covered by this European Standard.
The objective of this European Standard is to ensure the safe operation of such stations. This does not, however, relieve all concerned of the responsibility for taking the necessary care and applying effective quality management during the design, construction and operation.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12067-2 rev(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Part 2: Fuel/air ratio control / supervision of the electronic type
oSIST prEN 12067-2:2016

This European Standard specifies the safety, construction and performance requirements for electronic fuel/air ratio control (ERC), electronic fuel/air ratio supervision (ERS) and electronic fuel/air ratio trim (ERT) intended for use with burners and appliances burning gaseous or liquid fuels. It also describes the test procedures for evaluating these requirements and specifies information necessary for installation and use.
This standard is applicable to
-   closed loop fuel/air ratio controls (see 3.101),
-   fuel/air ratio supervision systems (see 3.102),
-   closed loop fuel/air ratio trim systems (see 3.103) and does not differentiate into classification by heat input.
This standard applies to ERC, ERS or ERT that can be tested independently, as well as part of an appliance or a burner.
NOTE 1 European Standards for burners, appliances or processes which use ERC, ERS or ERT can override the requirements of this standard.
NOTE 2 Provisions for production control are not part of this European Standard.

  • Draft
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/ASTM 52924:2023(Main)
Additive manufacturing of polymers - Qualification principles - Classification of part properties (ISO/ASTM 52924:2023)
SIST EN ISO/ASTM 52924:2023

This document establishes the required or the achievable classes of part properties for additive manufactured polymer parts in order to get a common understanding on part quality. It is aimed at providers of manufacturing services for polymer parts who use additive manufacturing machines and at the customers for these services. Designers of parts as well as buyers and providers of manufacturing services can specify, in a traceable manner, the required or the achievable level of part properties with the aid of this document. The classification is based on mechanical, physical and geometrical properties. Further properties can be defined between buyer and provider of manufacturing.
This document is applicable to parts that have been manufactured from a thermoplastic polymer by means of thermal reaction fusion of material typically applied by a powder bed fusion (PBF) or material extrusion (MEX) processes. This document is also applicable to thermoplastic parts made by other processes, provided that due consideration is given to process-specific topics.
The classification of part properties applies to parts in as-built condition, that have been unpacked from the build space, with all support structures removed, but prior to any post-processing operations.
Specific industries (e.g. aerospace and medical) typically specify additional requirements.

  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11363-1:2018/A1:2023(Amendment)
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Amendment 1 (ISO 11363-1:2018/Amd 1:2023)
SIST EN ISO 11363-1:2018/A1:2023
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11267:2023(Main)
Soil quality - Inhibition of reproduction of Collembola (Folsomia candida) by soil contaminants (ISO 11267:2023)
SIST EN ISO 11267:2023

This document specifies one of the methods for evaluating the habitat function of soils and determining effects of soil contaminants and substances on the reproduction of Folsomia candida Willem by dermal and alimentary uptake. This document also provides information on how to use this method for testing substances under temperate conditions.
The chronic test described is applicable to soils and soil materials of unknown quality, e.g. from contaminated sites, amended soils, soils after remediation, industrial, agricultural or other sites of concern and waste materials.
The method is not applicable to volatile substances, i.e. substances for which H (Henry's constant) or the air/water partition coefficient is greater than 1, or for which the vapour pressure exceeds 300 Pa at 25 °C.

  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19111:2020/A2:2023(Amendment)
Geographic information - Referencing by coordinates - Amendment 2 (ISO 19111:2019/Amd 2:2023)
SIST EN ISO 19111:2020/oprA2:2023
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3581:2023(Main)
Welding consumables - Covered electrodes for manual metal arc welding of stainless and heat-resisting steels - Classification (ISO 3581:2023)
SIST EN ISO 3581:2023

This document specifies requirements for classification of covered electrodes, based on the all-weld metal chemical composition, the type of electrode covering and other electrode properties, and the all-weld metal mechanical properties, in the as-welded or heat-treated conditions, for manual metal arc welding of stainless and heat-resisting steels.
This document is a combined standard providing for classification utilizing a system based upon classification according to nominal composition or utilizing a system based upon classification according to alloy type.
a)       Paragraphs and tables which carry the label “classification according to nominal composition-A” or “ISO 3581-A” are applicable only to products classified to that system.
b)       Paragraphs and tables which carry the label “classification according to alloy type-B” or “ISO 3581-B” are applicable only to products classified to that system.
c)        Paragraphs and tables which carry neither label are applicable to products classified according to either or both systems.
Annex B gives information on considerations on weld metal ferrite content.

  • Draft
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day