iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 24534-3:2016

(Main)

Intelligent transport systems - Automatic vehicle and equipment identification - Electronic registration identification (ERI) for vehicles - Part 3: Vehicle data (ISO 24534-3:2016)

Intelligent transport systems - Automatic vehicle and equipment identification - Electronic registration identification (ERI) for vehicles - Part 3: Vehicle data (ISO 24534-3:2016)

ISO 24534-3:2016 provides the requirements for an electronic registration identification (ERI) that is based on an identifier assigned to a vehicle (e.g. for recognition by national authorities) suitable to be used for the following:
-      electronic identification of local and foreign vehicles by national authorities;
-      vehicle manufacturing, in-life-maintenance, and end-of-life identification (vehicle life cycle management);
-      adaptation of vehicle data, e.g. in case of international re-sales;
-      safety-related purposes;
-      crime reduction;
-      commercial services;
-      adhering to privacy and data protection regulations.
ISO 24534-3:2016 defines the vehicle identification data. This data is called the ERI data and includes the following:
-      the vehicle identifier;
-      possible additional vehicle-related information (as typically included in a vehicle registration certificate).
All additional vehicle data elements are defined as optional. It is left to local legislation and/or the discretion of a registration authority to use or not to use a particular data element. If used, the value is assumed to be the one registered by the registration authority in accordance with local legislation. This part of ISO 24534 only provides the syntax for all these data elements.
NOTE          The secure application layer interfaces for the exchange of ERI data with an ERI reader or writer are specified in ISO 24534‑4 and in ISO 24534‑5.

Intelligente Verkehrssysteme - Automatische Identifizierung von Fahrzeugen und Ausrüstungen - Elektronische Identifizierung für die Registrierung (ERI) von Fahrzeugen - Teil 3: Fahrzeugdaten (ISO 24534-3:2016)

Systèmes de transport intelligents - Identification automatique des véhicules et des équipements - Identification d'enregistrement électronique (ERI) pour les véhicules - Partie 3: Données du véhicule (ISO 24534-3:2016)

ISO 24534-3:2016 spécifie les exigences pour l'identification d'enregistrement électronique (ERI) s'appuyant sur un identifiant attribué à un véhicule (par exemple, pour la reconnaissance par les autorités nationales), adapté:
-      à l'identification électronique des véhicules locaux et étrangers par les autorités nationales,
-      à l'identification pendant la fabrication, la maintenance et la fin de vie des véhicules (gestion du cycle de vie des véhicules),
-      à l'adaptation des données des véhicules, par exemple en cas de reventes à l'étranger,
-      aux besoins de la sécurité,
-      à la réduction des délits,
-      aux services commerciaux, et
-      au respect des réglementations concernant le respect de la vie privée et la protection des données.
ISO 24534-3:2016 définit les données d'identification des véhicules. Celles-ci sont appelées données ERI et comprennent:
-      l'identifiant du véhicule, et
-      de potentielles informations supplémentaires relatives au véhicule (telles que celles généralement incluses dans un certificat d'immatriculation de véhicule).
Toutes les données de véhicule supplémentaires sont facultatives. Le soin est laissé à la législation locale et/ou à l'autorité d'immatriculation d'utiliser ou non un élément de données particulier. En cas d'utilisation, la valeur est supposée être celle enregistrée par l'autorité d'immatriculation conformément à la législation locale. La présente partie de l'EN ISO 24534 ne fournit que la syntaxe de tous ces éléments de données.
NOTE          Les interfaces de la couche application sécurisée pour l'échange de données ERI avec un lecteur ou un enregistreur ERI sont spécifiées dans la Partie 4 de l'EN l'ISO 24534 et dans l'ISO 24534‑5.

Inteligentni transportni sistemi - Avtomatična identifikacija vozil in opreme - Elektronska identifikacija registracije (ERI) za vozila - 3. del: Podatki o vozilu (ISO 24534-3:2016)

Ta del standarda ISO/TS 24534 določa zahteve za elektronsko identifikacijo registracije (ERI), ki temelji na oznaki, dodeljeni vozilu (da jo npr. prepoznajo nacionalni organi), in se uporablja za naslednje:
– elektronsko identifikacijo lokalnih in tujih vozil, ki jo opravljajo nacionalni organi;
– proizvodnjo vozil, vzdrževanje v času življenjske dobe in identifikacijo ob koncu življenjske dobe (upravljanje življenjskega cikla vozila);
– prilagajanje podatkov o vozilu (npr. za mednarodno nadaljnjo prodajo);
– varnostne namene;
– zmanjšanje kriminala;
– komercialne storitve;
– upoštevanje predpisov o varovanju zasebnosti in osebnih podatkov.
Ta del standarda ISO 24534 določa identifikacijske podatke vozila. Ti podatki se imenujejo podatki ERI in vključujejo naslednje:
– identifikator vozila;
– morebitne dodatne informacije v zvezi z vozilom (običajno so vključene v potrdilu o registraciji vozila).
Vsi dodatni podatkovni elementi za vozila so opredeljeni kot izbirni. Uporaba oziroma neuporaba določenega podatkovnega elementa je odvisna od lokalne zakonodaje in/ali je stvar presoje registracijskega organa. V primeru uporabe se obravnava kot vrednost, ki jo registrira registracijski organ v skladu z lokalno zakonodajo. Ta del standarda ISO 24534 zagotavlja samo sintakso za takšne podatkovne elemente.
OPOMBA: vmesniki za varno aplikacijsko raven za izmenjavo podatkov ERI z bralnikom ali zapisovalnikom ERI so opredeljeni v standardih ISO 24534-4 in ISO 24534-5.

General Information

Status
Published
Publication Date
19-Apr-2016
Withdrawal Date
30-Oct-2016
ICS
03.220.20 - Road transport
35.240.60 - IT applications in transport
43.020 - Road vehicles in general
Technical Committee
CEN/TC 278 - Road transport and traffic telematics
Drafting Committee
CEN/TC 278/WG 12 - Automatic Vehicle Identification and Automatic Equipment Identification (AVI/AEI)
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Apr-2016
Completion Date
20-Apr-2016
Mandate
M/338 - Standardisation mandate to CEN, CENELEC and ETSI in support of interoperabilty of electonic road toll systems in the community
Ref Project
SIST EN ISO 24534-3:2016 - Intelligent transport systems - Automatic vehicle and equipment identification - Electronic registration identification (ERI) for vehicles - Part 3: Vehicle data (ISO 24534-3:2016)

Relations

Replaces
EN ISO 24534-3:2010 - Automatic vehicle and equipment identification - Electronic Registration Identification (ERI) for vehicles - Part 3: Vehicle data (ISO 24534-3:2010)
Effective Date
01-May-2013

Buy Standard

EN ISO 24534-3:2016EN ISO 24534-3:2016
PreviousNext
Standard
EN ISO 24534-3:2016
English language
66 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2016
1DGRPHãþD
SIST EN ISO 24534-3:2010
,QWHOLJHQWQLWUDQVSRUWQLVLVWHPL$YWRPDWLþQDLGHQWLILNDFLMDYR]LOLQRSUHPH
(OHNWURQVNDLGHQWLILNDFLMDUHJLVWUDFLMH (5, ]DYR]LODGHO3RGDWNLRYR]LOX ,62

Intelligent transport systems - Automatic vehicle and equipment identification - Electronic
registration identification (ERI) for vehicles - Part 3: Vehicle data (ISO 24534-3:2016)
Automatische Identifizierung von Fahrzeugen und Ausrüstungen - Elektronische
Identifizierung für die Registrierung (ERI) von Fahrzeugen - Teil 3: Fahrzeugdaten (ISO
24534-3:2016)
Systèmes de transport intelligents - Identification automatique des véhicules et des
équipements - Identification d'enregistrement électronique (ERI) pour les véhicules -
Partie 3: Données du véhicule (ISO 24534-3:2016)
Ta slovenski standard je istoveten z: EN ISO 24534-3:2016
ICS:
03.220.20 Cestni transport Road transport
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 24534-3
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2016
EUROPÄISCHE NORM
ICS 03.220.20; 35.240.60 Supersedes EN ISO 24534-3:2010
English Version
Intelligent transport systems - Automatic vehicle and
equipment identification - Electronic registration
identification (ERI) for vehicles - Part 3: Vehicle data (ISO
24534-3:2016)
Systèmes de transport intelligents - Identification Automatische Identifizierung von Fahrzeugen und
automatique des véhicules et des équipements - Ausrüstungen - Elektronische Identifizierung für die
Identification d'enregistrement électronique (ERI) Registrierung (ERI) von Fahrzeugen - Teil 3:
pour les véhicules - Partie 3: Données du véhicule (ISO Fahrzeugdaten (ISO 24534-3:2016)
24534-3:2016)
This European Standard was approved by CEN on 4 March 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24534-3:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
European foreword
This document (EN ISO 24534-3:2016) has been prepared by Technical Committee ISO/TC 204
“Intelligent transport systems” in collaboration with Technical Committee CEN/TC 278 “Intelligent
transport systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2016, and conflicting national standards shall
be withdrawn at the latest by October 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 24534-3:2010.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 24534-3:2016 has been approved by CEN as EN ISO 24534-3:2016 without any
modification.
INTERNATIONAL ISO
STANDARD 24534-3
Second edition
2016-04-01
Intelligent transport systems —
Automatic vehicle and equipment
identification — Electronic
registration identification (ERI) for
vehicles —
Part 3:
Vehicle data
Systèmes de transport intelligents — Identification automatique
des véhicules et des équipements — Identification d’enregistrement
électronique (ERI) pour les véhicules —
Partie 3: Données du véhicule
Reference number
ISO 24534-3:2016(E)
©
ISO 2016
ISO 24534-3:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 24534-3:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Abbreviations. 3
5 Requirements . 3
5.1 Vehicle identification data . 3
5.2 Vehicle identifier . 4
5.3 ERI data type . 5
5.4 Additional ERI data type . 5
5.5 Additional ERI registration data . 5
5.5.1 Additional ERI registration data type . 5
5.5.2 Administrative types .11
5.5.3 EU vehicle category code type.12
5.5.4 Other Vehicle type types .13
5.5.5 ISO 3833 vehicle type .14
5.5.6 Other vehicle shape types .15
5.5.7 Number of passenger, axles, and mass types .15
5.5.8 Engine and power source types .17
5.5.9 Environmental types .18
5.5.10 Official test data type .19
5.5.11 Types used for EFC .19
5.5.12 Other types.26
5.6 Attributes .28
5.6.1 Introduction .28
5.6.2 Useful types .28
5.6.3 Useful sets of attributes .29
5.6.4 Information object class ATTRIBUTES .29
5.6.5 Attribute definitions .29
5.7 Encoding .30
Annex A (normative) ASN.1 Modules .31
Annex B (informative) Combined ERI data and local registrations .50
Annex C (informative) Correspondance with EFC attributes .54
Bibliography .56
ISO 24534-3:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 24534-1:2010(Main)
Automatic vehicle and equipment identification - Electronic Registration Identification (ERI) for vehicles - Part 1: Architecture (ISO 24534-1:2010)
SIST EN ISO 24534-1:2012

ISO 24534-1:2010 provides requirements for electronic registration identification (ERI) that are based on an identifier assigned to a vehicle (e.g. for recognition by national authorities), suitable to be used for:
electronic identification of local and foreign vehicles by national authorities;
vehicle manufacturing, in-life maintenance and end-of-life identification (vehicle life cycle management);
adaptation of vehicle data (e.g. for international resales);
safety-related purposes;
crime reduction;
commercial services.
It adheres to privacy and data protection regulations.
ISO 24534-1:2010 provides an overview of the ERI system concept, in terms of the onboard vehicle components and the external off-vehicle components required for an operational system. The detailed requirements are defined in Parts 2, 3, 4 and 5 of ISO 24534 and more limited, though relevant, provisions are defined in ISO 24535.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 24534-2:2010(Main)
Automatic vehicle and equipment identification - Electronic Registration Identification (ERI) for vehicles - Part 2: Operational requirements (ISO 24534-2:2010)
SIST EN ISO 24534-2:2010

ISO 24534-2:2010 provides requirements for electronic registration identification (ERI) that are based on an identifier assigned to a vehicle (e.g. for recognition by national authorities) suitable to be used for:
electronic identification of local and foreign vehicles by national authorities;
vehicle manufacturing, in-life maintenance and end-of-life identification (vehicle life cycle management);
adaptation of vehicle data (e.g. for international resales);
safety-related purposes;
crime reduction;
commercial services.
It adheres to privacy and data protection regulations.
ISO 24534-2:2010 defines the operational requirements for the remaining parts of ISO 24534 and the more limited but relevant provisions of ISO 24535.
Whilst the definition of the organizational framework required to implement, operate and maintain an ERI system is outside the scope of ISO 24534-2:2010, a list of potential stakeholders in the public and private sector has been included.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 24534-4:2010(Main)
Automatic vehicle and equipment identification - Electronic Registration Identification (ERI) for vehicles - Part 4: Secure communications using asymmetrical techniques (ISO 24534-4:2010)
SIST EN ISO 24534-4:2010

ISO 24534-4:2010 provides requirements for electronic registration identification (ERI) that are based on an identifier assigned to a vehicle (e.g. for recognition by national authorities) suitable to be used for:
electronic identification of local and foreign vehicles by national authorities;
vehicle manufacturing, in-life maintenance and end-of-life identification (vehicle life cycle management);
adaptation of vehicle data (e.g. for international resales);
safety-related purposes;
crime reduction;
commercial services.
It adheres to privacy and data protection regulations.
ISO 24534-4:2010 specifies the interfaces for a secure exchange of data between an ERT and an ERI reader or ERI writer in or outside the vehicle using asymmetric encryption techniques.
ISO 24534-4:2010 includes:
the application layer interface between an ERT and an onboard ERI reader or writer;
the application layer interface between the onboard ERI equipment and external ERI readers and writers;
security issues related to the communication with the ERT.

  • Standard
    102 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 24534-1:2010(Main)
Automatic vehicle and equipment identification - Electronic Registration Identification (ERI) for vehicles - Part 1: Architecture (ISO 24534-1:2010)
SIST EN ISO 24534-1:2012

ISO 24534-1:2010 provides requirements for electronic registration identification (ERI) that are based on an identifier assigned to a vehicle (e.g. for recognition by national authorities), suitable to be used for:
electronic identification of local and foreign vehicles by national authorities;
vehicle manufacturing, in-life maintenance and end-of-life identification (vehicle life cycle management);
adaptation of vehicle data (e.g. for international resales);
safety-related purposes;
crime reduction;
commercial services.
It adheres to privacy and data protection regulations.
ISO 24534-1:2010 provides an overview of the ERI system concept, in terms of the onboard vehicle components and the external off-vehicle components required for an operational system. The detailed requirements are defined in Parts 2, 3, 4 and 5 of ISO 24534 and more limited, though relevant, provisions are defined in ISO 24535.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 24534-2:2010(Main)
Automatic vehicle and equipment identification - Electronic Registration Identification (ERI) for vehicles - Part 2: Operational requirements (ISO 24534-2:2010)
SIST EN ISO 24534-2:2010

ISO 24534-2:2010 provides requirements for electronic registration identification (ERI) that are based on an identifier assigned to a vehicle (e.g. for recognition by national authorities) suitable to be used for:
electronic identification of local and foreign vehicles by national authorities;
vehicle manufacturing, in-life maintenance and end-of-life identification (vehicle life cycle management);
adaptation of vehicle data (e.g. for international resales);
safety-related purposes;
crime reduction;
commercial services.
It adheres to privacy and data protection regulations.
ISO 24534-2:2010 defines the operational requirements for the remaining parts of ISO 24534 and the more limited but relevant provisions of ISO 24535.
Whilst the definition of the organizational framework required to implement, operate and maintain an ERI system is outside the scope of ISO 24534-2:2010, a list of potential stakeholders in the public and private sector has been included.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 24534-4:2010(Main)
Automatic vehicle and equipment identification - Electronic Registration Identification (ERI) for vehicles - Part 4: Secure communications using asymmetrical techniques (ISO 24534-4:2010)
SIST EN ISO 24534-4:2010

ISO 24534-4:2010 provides requirements for electronic registration identification (ERI) that are based on an identifier assigned to a vehicle (e.g. for recognition by national authorities) suitable to be used for:
electronic identification of local and foreign vehicles by national authorities;
vehicle manufacturing, in-life maintenance and end-of-life identification (vehicle life cycle management);
adaptation of vehicle data (e.g. for international resales);
safety-related purposes;
crime reduction;
commercial services.
It adheres to privacy and data protection regulations.
ISO 24534-4:2010 specifies the interfaces for a secure exchange of data between an ERT and an ERI reader or ERI writer in or outside the vehicle using asymmetric encryption techniques.
ISO 24534-4:2010 includes:
the application layer interface between an ERT and an onboard ERI reader or writer;
the application layer interface between the onboard ERI equipment and external ERI readers and writers;
security issues related to the communication with the ERT.

  • Standard
    102 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2588:2024(Main)
Aerospace series - Bearing, spherical plain in corrosion resisting steel with assembly slots - Dimensions and loads
kSIST FprEN 2588:2024

This document specifies the characteristics of spherical plain bearings in corrosion resisting steel, with assembly slots, metric series, with or without lubrication holes and groove, intended for use in fixed or moving parts of aircraft structure and control mechanisms, within the temperature range from −54 °C to 150 °C.
It also applies to the following temperature ranges when lubricated with the following greases (see EN 2337):
-   ester type very high pressure grease (code letter A), operating range from −73 °C to 121 °C;
-   synthetic hydrocarbon type very high pressure grease general purpose (code letter B), operating range from −54 °C to 177 °C.
Their field of application when lubricated with grease code letter A is limited to 121 °C.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 18075:2024(Main)
Resilient, textile, laminate and modular mechanical locked floor coverings - Circular economy and sustainability - Recommendations/guidelines for design
kSIST-TS FprCEN/TS 18075:2024

The aim of this document is to provide general recommendations and guidelines on how to design a product to optimize its reuse and recyclability at the end of its lifetime as well as to take into account sustainable sourcing of materials for all floor covering product groups covered by CEN/TC 134. The overall target is to avoid waste and pollution and to achieve a product fit for the circular economy.
In a linear economy, the focus of product design is on developing new products without considering the recycling or reuse of the raw materials used.
This document provides guidance for processes allowing for (raw) materials used to be returned to the economic cycle based on circular design principles. The focus is on open systems that allow for economically interesting alternatives and are not limited to the principle of closed cycles (product to product).
Specific attention is given to renewable materials, where applicable.
The document is structured along the life cycle of the products, starting with the production phase.
Excluded is packaging, which is not considered part of the product end-of-life stage.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-3:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 3: Tests for emissions of volatile organic substances (ISO 18562-3:2024)
kSIST FprEN ISO 18562-3:2024

This document specifies tests for the emissions of volatile organic substances from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify emissions of volatile organic substances that are added to the respirable gas stream by the materials of the gas pathway. This document establishes acceptance criteria for these tests.
NOTE            Gaseous emission of volatile organic substances includes emissions of volatile organic compounds, semi-volatile organic compounds and very volatile organic compounds.
This document addresses potential contamination of the gas stream arising from the gas pathways of medical devices or accessories, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the surfaces of gas pathways that are in direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories containing gas pathways that are addressed by this document include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 series.
This document is intended to be read in conjunction with ISO 18562-1.

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 899-2:2024(Main)
Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2024)
kSIST FprEN ISO 899-2:2024

This document specifies a method for determining the flexural creep of plastics in the form of standard test specimens under specified conditions such as those of pre-treatment, temperature and humidity. It is only applicable to a simple freely supported beam loaded at mid-span (three-point-loading test).
 The method is suitable for use with rigid and semi-rigid non-reinforced, filled and fibre-reinforced plastics materials (see ISO 472 for definitions) test specimens moulded directly or machined from sheets or moulded articles.
NOTE            The method can be unsuitable for certain fibre-reinforced materials due to differences in fibre orientation
The method is intended to provide data for engineering-design, quality control, research and development purposes.
The method might not be applicable for determining the flexural creep of rigid cellular plastics (attention is drawn in this respect to ISO 1209-1 and ISO 1209-2).

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day