EN ISO 10256-4:2018
(Main)Protective equipment for use in ice hockey - Part 4: Head and face protection for goalkeepers (ISO 10256-4:2016)
Protective equipment for use in ice hockey - Part 4: Head and face protection for goalkeepers (ISO 10256-4:2016)
ISO 10256-4:2016 covers performance requirements for head and face protectors to be used by ice hockey goalkeepers. It is intended to be read in conjunction with ISO 10256‑1, ISO 10256‑2 and ISO 10256‑3.
Performance requirements are established, where appropriate for the following:
a) materials, assembly, and design;
b) protected areas (coverage) and penetration resistance;
c) shock absorption;
d) puck impact resistance;
e) retention;
f) optical quality.
NOTE 1 The requirements of a clause take precedent over a figure.
NOTE 2 The intent of this part of ISO 10256 is to reduce the risk of injury to the head and face of ice hockey goalkeepers without compromising the form and appeal of the game.
Schutzausrüstung zum Gebrauch beim Eishockey - Teil 4: Kopf- und Gesichtsschutz für Torhüter (ISO 10256-4:2016)
Dieser Teil der ISO 10256 umfasst Leistungsanforderungen für Kopf und Gesichtsschützern, die von Eishockeytorhütern verwendet werden. Sie ist vorgesehen, in Verbindung mit ISO 10256 1, ISO 10256 2 und ISO 10256 3 gelesen zu werden.
Leistungsanforderungen, wo anwendbar, sind für folgende Punkte festgelegt:
a) Werkstoffe, Zusammenbau und Ausführung;
b) geschützte Bereiche (Bedeckung) und Durchdringungsfestigkeit;
c) Stoßdämpfung;
d) Puckaufprallwiderstand;
e) Trageeinrichtung;
f) optische Qualität.
ANMERKUNG 1 Die in einem Abschnitt angegebenen Anforderungen haben Vorrang vor einem Bild.
ANMERKUNG 2 Der Zweck dieses Teils der ISO 10256 ist die Verringerung des Risikos von Kopf und Gesichtsver-letzungen von Eishockeytorhütern, ohne die Form oder die Attraktivität des Spiels zu beeinflussen.
Équipements de protection destinés à être utilisés en hockey sur glace - Partie 4: Protections de tête et de visage pour les gardiens de but (ISO 10256-4:2016)
ISO 10256-4:2016 spécifie les exigences de performance applicables aux protections de tête et de visage destinées aux gardiens de but de hockey sur glace. Elle doit être lue en complément de l'ISO 10256‑1, de l'ISO 10256‑2 et de l'ISO 10256‑3.
ISO 10256-4:2016 établit, s'il y a lieu, des exigences de performance pour les aspects suivants:
a) matériaux, assemblage et conception;
b) zones protégées (recouvrement) et résistance à la pénétration;
c) absorption des chocs;
d) résistance à l'impact du palet;
e) rétention;
f) qualité optique.
NOTE 1 Les exigences d'un article prévalent sur celles d'une figure.
NOTE 2 L'objectif de la présente partie de l'ISO 10256 est de réduire le risque de blessure à la tête et au visage des gardiens de but de hockey sur glace sans compromettre pour autant l'aspect ou l'attrait même du jeu.
Varovalna oprema za uporabo pri hokeju na ledu - 4. del: Zaščita glave in obraza za vratarje (ISO 10256-4:2016)
Ta mednarodni standard določa zahteve glede učinkovitosti ščitnikov za glavo in obraz vratarjev pri hokeju na ledu. Standard je treba uporabljati v povezavi s standardi ISO 10256-1, 10256-2 in 10256-3. Namen tega mednarodnega standarda je zmanjšati tveganje za poškodbe glave ali obraza vratarjev pri hokeju na ledu brez vpliva na način ali privlačnost igre. Zahteve glede učinkovitosti so po potrebi določene za:
a) material, sestav in zasnovo; b) zaščitena mesta (pokritost) in neprepustnost; c) ublažitev udarcev; d) odpornost proti udarcu ploščka; e) zadrževanje; f) optično kakovost.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2018
9DURYDOQDRSUHPD]DXSRUDERSULKRNHMXQDOHGXGHO =DãþLWDJODYHLQREUD]D
]DYUDWDUMH ,62
Protective equipment for use in ice hockey - Part 4: Head and face protection for
goalkeepers (ISO 10256-4:2016)
Schutzausrüstung zum Gebrauch beim Eishockey - Teil 4: Kopf- und Gesichtsschutz für
Torhüter (ISO 10256-4:2016)
Équipements de protection destinés à être utilisés en hockey sur glace - Partie 4:
Protections de tête et de visage pour les gardiens de but (ISO 10256-4:2016)
Ta slovenski standard je istoveten z: EN ISO 10256-4:2018
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
97.220.20 Oprema za zimske športe Winter sports equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10256-4
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2018
EUROPÄISCHE NORM
ICS 97.220.20; 13.340.20
English Version
Protective equipment for use in ice hockey - Part 4: Head
and face protection for goalkeepers (ISO 10256-4:2016)
Équipements de protection destinés à être utilisés en Schutzausrüstung zum Gebrauch beim Eishockey - Teil
hockey sur glace - Partie 4: Protections de tête et de 4: Kopf- und Gesichtsschutz für Torhüter (ISO 10256-
visage pour les gardiens de but (ISO 10256-4:2016) 4:2016)
This European Standard was approved by CEN on 17 September 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10256-4:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 10256-4:2018) has been prepared by Technical Committee ISO/TC 83 "Sports
and other recreational facilities and equipment" in collaboration with Technical Committee
CEN/TC 158 “Head protection” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2018, and conflicting national standards shall
be withdrawn at the latest by October 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10256-4:2016 has been approved by CEN as EN ISO 10256-4:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 10256-4
First edition
2016-12-01
Protective equipment for use in ice
hockey —
Part 4:
Head and face protection for
goalkeepers
Équipements de protection destinés à être utilisés en hockey sur
glace —
Partie 4: Protections de tête et de visage pour les gardiens de but
Reference number
ISO 10256-4:2016(E)
©
ISO 2016
ISO 10256-4:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
ISO 10256-4:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 General . 2
4.2 Design . 2
4.2.1 Padding . 2
4.2.2 Load-bearing area . 2
4.2.3 Welded wire components . 2
4.2.4 Overlap . 2
4.2.5 Minimum distance (headform to face protector) . 3
4.2.6 Maximum distance (headform to face protector) . 3
4.3 Protected areas (coverage) . 3
4.3.1 Protected area of the head . 3
4.3.2 Protected area of the face . 3
4.4 Penetration resistance . 3
4.4.1 General. 3
4.4.2 Types D1 and D2 . 3
4.4.3 Type D3 . 3
4.5 Shock-absorbing capacity . 3
4.6 Puck impact resistance . 3
4.6.1 Contact test . 3
4.6.2 Toughness test . 4
4.7 Retention system . 4
4.8 Field of vision . 4
5 Test methods . 4
5.1 General . 4
5.1.1 Tolerances and uncertainty estimations . 4
5.1.2 Samples . 4
5.1.3 Component assemblies . 5
5.2 Conditioning . 5
5.3 Protector positioning . 5
5.4 Protected area (coverage) test . 5
5.4.1 Protected area of the head . 5
5.4.2 Protected area of the face . 5
5.4.3 Coverage test . 5
5.5 Penetration test . 5
5.5.1 Test apparatus . 5
5.5.2 Procedures . 6
5.6 Shock absorbing capacity test . . 6
5.7 Puck impact resistance test. 6
6 Test report . 6
7 Permanent marking .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.