EN 13557:2003+A2:2008
(Main + Amendment)Cranes - Controls and control stations
Cranes - Controls and control stations
This European Standard specifies health and safety design requirements for controls and control stations for all types of crane.
NOTE 1 Control systems are covered by other standards e.g. EN 60204-32, prEN 13135-1 and prEN 13135-2.
Annex C provides additional value to the requirements for cableless control systems as specified in EN 60204-32.
NOTE 2 Annex C will be deleted after WG 3 agreed to introduce it into their document prEN 13135-1.
NOTE 3 Specific requirements for particular types of crane are given in the appropriate European Standard for the particular crane type.
This standard does not deal with noise hazards because these are dealt with in safety standards for specific types of cranes. It also does not address the design of the cabin with regard to its sound insulation properties.
This European Standard covers specific hazards which could occur during the use of controls and control stations. It does not cover hazards which could occur during transport, construction, commissioning, modification, maintenance, de-commissioning or disposal.
The hazards covered by this standard are identified in clause 4.
This European Standard is applicable after the date of approval by CEN of this standard.
Krane - Stellteile und Steuerstände
Diese Europäische Norm legt Gesundheits- und Sicherheitsanforderungen an die Gestaltung von in allen Kranarten eingebauten Stellteilen und Steuerständen fest.
ANMERKUNG 1 Steuerungssysteme sind in anderen Normen behandelt wie z. B. EN 60204-32, EN 13135-1 und prEN 13135-2EN 60204-32, EN 13135-1 und prEN 13135-2.
Anhang C legt ergänzende Anforderungen für kabellose Steuerungen zu denen in EN 60204-32EN 60204-32 fest.
ANMERKUNG 2 Anhang Cg C entfällt, wenn die WG 3 zustimmt, ihn in das Dokument EN 13135-1 zu übernehmen.
ANMERKUNG 3 Besondere Anforderungen für einzelne Kranarten sind in den entsprechenden Normen für die einzelnen Kranarten angegeben.
Diese Norm behandelt nicht Gefährdungen durch Lärm, da diese in Sicherheitsnormen für spezifische Kranarten behandelt sind. Sie behandelt gleichfalls nicht die Konstruktion des Führerhauses hinsichtlich der Schallisolierungseigenschaften.
Diese Europäische Norm behandelt spezifische Gefährdungen, die während der Benutzung von Stellteilen und Steuerständen entstehen könnten. Sie behandelt nicht Gefährdungen, die während Transport, Bau, Inbetriebnahme, Änderung, Instandhaltung, Außerbetriebnahme oder Entsorgung auftreten könnten.
Die in dieser Norm behandelten Gefährdungen sind in Abschnitt 4 angegeben.
Diese Europäische Norm gilt nach dem Datum der Annahme dieser Norm durch das CEN.
Appareils de levage à charge suspendue - Commandes et postes de conduite
La présente Norme européenne spécifie les prescriptions de sécurité et de santé relatives à la conception des commandes et des postes de conduite pour tous types d'appareils de levage à charge suspendue.
NOTE 1 Les systèmes de commande font l’objet d’autres normes, par exemple l’EN 60204-32, l’EN 13135-1 et le prEN 13135-2.
L’Annexe C spécifie des prescriptions supplémentaires pour les systèmes de commande sans fil tels que spécifiés dans l’EN 60204-32.
NOTE 2 L’Annexe C sera supprimée lorsque le GT 3 l’aura introduite dans l’EN 13135 1.
NOTE 3 Les prescriptions particulières pour des types particuliers d'appareils de levage à charge suspendue sont données dans les Normes européennes appropriées aux types d'appareil de levage à charge suspendue particuliers.
La présente norme ne traite pas des dangers liés au bruit, qui font l’objet de normes de sécurité pour des types spécifiques d'appareils de levage à charge suspendue. Elle ne traite pas non plus de la conception de la cabine du point de vue de l’isolation phonique.
La présente Norme européenne couvre les phénomènes dangereux spécifiques qui peuvent survenir durant l'utilisation de commandes et de postes de conduite. Elle ne couvre pas les risques qui peuvent survenir durant le transport, la construction, la mise en service, la modification, la maintenance, la mise hors service ou au rebut.
Les phénomènes dangereux couverts par la présente norme sont identifiés à l'article 4.
La présente Norme européenne est applicable à partir de la date à laquelle le CEN a approuvé cette norme.
Dvigala (žerjavi) - Upravljala in upravljalna mesta
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cranes - Controls and control stationsDvigala (žerjavi) - Upravljala in upravljalna mestaAppareils de levage à charge suspendue - Commandes et postes de conduiteKrane - Stellteile und Steuerstände53.020.20DvigalaCranesICS:SIST EN 13557:2004+A2:2008en,frTa slovenski standard je istoveten z:EN 13557:2003+A2:200801-julij-2008SIST EN 13557:2004+A2:2008SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13557:2003+A2
April 2008 ICS 53.020.20 Supersedes EN 13557:2003 English Version
Cranes - Controls and control stations
Appareils de levage à charge suspendue - Commandes et postes de conduite
Krane - Stellteile und Steuerstände This European Standard was approved by CEN on 1 September 2003 and includes Amendment 1 approved by CEN on 26 September 2005 and Amendment 2 approved by CEN on 4 March 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13557:2003+A2:2008: E
Operative temperature and globe temperature.22 A.1 Operative temperature.22 A.2 Globe temperature.22 Annex B (informative)
List of existing design rules for cranes which cover structural design of control stations.23 Annex C (normative)
Additional requirements for cableless controls and control systems.24 C.1 General.24 C.2 Control limitation.24 C.3 Stop.24 C.4 Serial data communication.25 C.5 Use of more than one operator control station.25 C.6 Battery-powered operator control stations.25 C.7 Receiver.25 C.8 Warnings.25 C.9 Information for use.25 Annex ZA (informative)
####Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC.26 Annex ZB (informative)
####Relationship between this European standard and the Essential Requirements of EU Directive 2006/42/EC.27 Bibliography.28
1 Scope This European Standard specifies health and safety design requirements for controls and control stations for all types of crane. NOTE 1 Control systems are covered by other standards
e.g. EN 60204-32, EN 13135-1 and prEN 13135-2.
Annex C provides additional value to the requirements for cableless control systems as specified in EN 60204-32. NOTE 2 Annex C will be deleted after WG 3 agreed to introduce it into their document EN 13135-1. NOTE 3 Specific requirements for particular types of crane are given in the appropriate European Standard for the particular crane type. This standard does not deal with noise hazards because these are dealt with in safety standards for specific types of cranes. It also does not address the design of the cabin with regard to its sound insulation properties. This European Standard covers specific hazards which could occur during the use of controls and control stations. It does not cover hazards which could occur during transport, construction, commissioning, modification, maintenance, de-commissioning or disposal. The hazards covered by this standard are identified in clause 4. This European Standard is applicable after the date of approval by CEN of this standard. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 292-1:1991, Safety of machinery – Basic concepts, general principles for design - Part 1: Basic terminology, methodology. EN 292-2:1991, Safety of machinery – Basic concepts, general principles for design - Part 2: Technical principles and specifications. EN 418, Safety of machinery - Emergency stop equipment, functional aspects - Principles for design. EN 954-1:1996, Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design. EN 1070:1998, Safety of machinery – Terminology. EN ISO 5353:1998, Earth-moving machinery and tractors and machinery for agriculture and forestry - Seat index point (ISO 5353:1995). EN 60068-2-27, Basic environmental testing procedures - Part 2: Tests; test Ea and guidance: Shock (IEC 60068-2-27:1987). EN 60068-2-32, Basic environmental testing procedures – Part 2: Tests; test Ed: Free fall (IEC 60068-2-32:1975). EN 60068-2-64, Environmental testing - Part 2: Test methods; test Fh. Vibration, broad-band random (digital control) and guidance (IEC 60068-2-64:1993).
(IEC/TR3 60870-1-3) 3.10 hatch aperture fitted with a cover and used for access purposes 3.11 operating command control signal which is intended to initiate, modify or maintain a crane function / movement 3.12 operative temperature (t0) uniform temperature of an imaginary black enclosure in which an occupant would exchange the same amount of heat by radiation plus convection as in the actual non-uniform environment (see annex A) 3.13 receiver part of a cable-less control system which receives the commands from the transmitter 3.14 transmitter part of a cable-less control system which sends the crane driver's commands to the receiver 4 Significant hazards Table 1 contains all the significant hazards, hazardous situations and events, as
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.