EN ISO 13164-3:2020
(Main)Water quality - Radon-222 - Part 3: Test method using emanometry (ISO 13164-3:2013)
Water quality - Radon-222 - Part 3: Test method using emanometry (ISO 13164-3:2013)
ISO 13164-3:2013 specifies a test method for the determination of radon-222 activity concentration in a sample of water following its transfer from the aqueous phase to the air phase by degassing and its detection. It gives recommendations for rapid measurements performed within less than 1 h.
The radon-222 activity concentrations, which can be measured by this test method utilizing currently available instruments, range from 0,1 Bq l−1 to several hundred thousand becquerels per litre for a 100 ml test sample.
This test method is used successfully with drinking water samples. The laboratory is responsible for ensuring the validity of this test method for water samples of untested matrices.
This test method can be applied on field sites or in the laboratory.
Annexes A and B give indications on the necessary counting conditions to meet the required sensitivity for drinking water monitoring
Wasserbeschaffenheit - Radon-222 - Teil 3: Verfahren mittels Emanometrie (ISO 13164-3:2013)
Dieser Teil von ISO 13164 legt ein Verfahren zur Bestimmung der Radon 222 Aktivitätskonzentration in einer Wasserprobe fest, nachdem diese durch Entgasen von der wässrigen Phase in die Luftphase übergegangen ist und nachgewiesen wurde. Er gibt Empfehlungen für Schnellmessungen, die innerhalb von weniger als 1 h durchgeführt werden.
Die Radon 222 Aktivitätskonzentrationen, die mit diesem Verfahren unter Verwendung derzeit verfügbarer Instrumente gemessen werden können, reichen von 0,1 Bq l−1 bis zu mehreren hundert-tausend Becquerel je Liter für eine 100 ml Analysenprobe.
Dieses Verfahren wird erfolgreich bei Trinkwasserproben eingesetzt. Das Labor ist dafür verantwortlich, die Gültigkeit dieses Prüfverfahrens für Wasserproben ungeprüfter Matrizen sicherzustellen.
Dieses Prüfverfahren kann vor Ort oder im Labor angewendet werden.
Die Anhänge A und B enthalten Angaben zu den erforderlichen Zählbedingungen, um die für die Trinkwasser¬überwachung erforderliche Empfindlichkeit zu erreichen.
Qualité de l’eau - Radon 222 - Partie 3: Méthode d’essai par émanométrie (ISO 13164-3:2013)
L'ISO 13164-3:2013 spécifie une méthode d'essai permettant de déterminer l'activité volumique du radon 222 dans un échantillon d'eau après son transfert de la phase aqueuse vers la phase air par dégazage et sa détection. Elle donne des recommandations concernant des mesures rapides effectuées sur une période inférieure à 1 h.
Les valeurs d'activité volumique du radon 222, qui peuvent être mesurées par cette méthode d'essai à l'aide d'instruments actuellement disponibles, sont comprises entre 0,1 Bq l−1 et plusieurs centaines de milliers de becquerels par litre pour un échantillon d'essai de 100 ml.
Cette méthode d'essai est utilisée avec succès sur des échantillons d'eau potable. Il appartient au laboratoire de garantir la validité de cette méthode d'essai pour des échantillons d'eau provenant de matrices non soumises à essai.
Cette méthode d'essai peut être mise en oeuvre sur site ou en laboratoire.
Les annexes donnent des indications sur les conditions de comptage nécessaires pour obtenir la sensibilité requise pour la surveillance de l'eau potable.
Kakovost vode - Radon Rn-222 - 3. del: Preskusna metoda z emanometrijo (ISO 13164-3:2013)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2020
Kakovost vode - Radon Rn-222 - 3. del: Preskusna metoda z emanometrijo (ISO
13164-3:2013)
Water quality - Radon-222 - Part 3: Test method using emanometry (ISO 13164-3:2013)
Wasserbeschaffenheit - Radon-222 - Teil 2: Verfahren mittels Emanometrie (ISO 13164-
3:2013)
Qualité de l’eau - Radon 222 - Partie 3: Méthode d’essai par émanométrie (ISO 13164-
3:2013)
Ta slovenski standard je istoveten z: EN ISO 13164-3:2020
ICS:
13.060.60 Preiskava fizikalnih lastnosti Examination of physical
vode properties of water
17.240 Merjenje sevanja Radiation measurements
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 13164-3
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2020
EUROPÄISCHE NORM
ICS 13.060.60; 17.240; 13.280
English Version
Water quality - Radon-222 - Part 3: Test method using
emanometry (ISO 13164-3:2013)
Qualité de l'eau - Radon 222 - Partie 3: Méthode d'essai Wasserbeschaffenheit - Radon-222 - Teil 2: Verfahren
par émanométrie (ISO 13164-3:2013) mittels Emanometrie (ISO 13164-3:2013)
This European Standard was approved by CEN on 6 October 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13164-3:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 13164-3:2013 has been prepared by Technical Committee ISO/TC 147 "Water quality”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO 13164-
3:2020 by Technical Committee CEN/TC 230 “Water analysis” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2020, and conflicting national standards shall
be withdrawn at the latest by August 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 13164-3:2013 has been approved by CEN as EN ISO 13164-3:2020 without any
modification.
INTERNATIONAL ISO
STANDARD 13164-3
First edition
2013-09-01
Water quality — Radon-222 —
Part 3:
Test method using emanometry
Qualité de l’eau — Radon 222 —
Partie 3: Méthode d’essai par émanométrie
Reference number
ISO 13164-3:2013(E)
©
ISO 2013
ISO 13164-3:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
ISO 13164-3:2013(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols . 2
3.1 Terms and definitions . 2
3.2 Symbols . 2
4 Principle . 3
5 Sampling . 3
5.1 General requirement . 3
5.2 Sampling requirement . 3
5.3 Sample volume . 3
5.4 Container characteristics . 3
6 Transportation and storage . 4
7 Transfer of radon by degassing . 4
7.1 Purpose . 4
7.2 Principle . 4
8 Detection . 4
8.1 Objective . 4
8.2 Principle . 4
8.3 Silver-activated zinc sulfide ZnS(Ag) scintillation . 4
8.4 Air ionization . 5
8.5 Semiconductor (alpha-detection). 5
9 Quality assurance and quality control programme . 5
9.1 General . 5
9.2 Influence quantities . 5
9.3 Instrument verification. 6
9.4 Method verification . 6
9.5 Demonstration of analyst capability . 6
10 Expression of results . 6
10.1 Activity concentration . 6
10.2 Standard uncertainty of the activity concentration . 7
10.3 Decision threshold and detection limit . 7
10.4 Confidence limits. 7
11 Calibration . 7
12 Test report . 7
Annex A (informative) Examples of measurement methods using scintillation cells .9
Annex B (informative) Example of a measurement method using an ionization chamber .17
Bibliography .23
ISO 13164-3:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2, www.iso.org/directives.
Attention is drawn to the possibility that some of the elements of this docu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.